CJM Billet Intake Manifold

jwick · 12-28-2018, 02:46 PM

phunk · 12-28-2018, 02:52 PM

Quote:

Originally Posted by FPenvy

cant wait to see this all setup in the car with piping.

curious to see the pipe routing. this mani could make a splash in the GTR market especially with the big HP going front low mounted turbos.

We are interested in working with a R35 builder to construct one of these manifolds for them. If you run into anyone who would be interested, send them our way. No GT-R tax (for the first one

)

Jinxx · 12-28-2018, 05:09 PM

I am curious...with the throttle bodies in the front you would have to have 90 degree couplers there and another set of 90 degree couplers to get down into the intercooler ....wouldn’t they be more restrictive to the flow than the OEM manifold ...even with a NA setup with filters located there the 90 degree bend would have to restrict flow over the OEM set up.

phunk · 12-28-2018, 05:19 PM

We wont have any 90s we will be going straight forward into the top of the intercooler.

But if someone did want to put elbows on there, its not really going to make a difference. Your average turbo system has tons of 90 degree bends including the compressor housing outlets, inside the intercooler end tanks to enter the core, and all the several feet of piping to get around the core support. You could most likely end up without any more bending than the stock location throttles if you plan your pipes well, possibly even less bends. But the way we are using it, we will have eliminated several bends and at least 4 feet of charge piping, if not closer to 6 feet.

Attached some examples of our DE billet manifolds in use.

Spooler · 12-28-2018, 05:27 PM

Those pictures make sense. Just a redo of the intercooler for the piping to come out the top.

Rusty · 12-28-2018, 05:52 PM

phunk · 12-28-2018, 05:57 PM

Quote:

Originally Posted by Spooler

Those pictures make sense. Just a redo of he intercooler for the piping to come out the top.

Yup we will use our existing intercooler kit and just make a custom end tank for this build.

Spooler · 12-28-2018, 06:32 PM

I can't wait to see Justin's car up and running with the new intake/intercooler setup.

Jinxx · 12-28-2018, 06:43 PM

Quote:

Originally Posted by phunk

We wont have any 90s we will be going straight forward into the top of the intercooler.

But if someone did want to put elbows on there, its not really going to make a difference. Your average turbo system has tons of 90 degree bends including the compressor housing outlets, inside the intercooler end tanks to enter the core, and all the several feet of piping to get around the core support. You could most likely end up without any more bending than the stock location throttles if you plan your pipes well, possibly even less bends. But the way we are using it, we will have eliminated several bends and at least 4 feet of charge piping, if not closer to 6 feet.

Attached some examples of our DE billet manifolds in use.

I was thinking from most of the other turbo kits just the difference from their location going to the stock location ... to add this manifold to a existing kit ... you would add 4 90 degree elbows ... I guess it wouldnt be a big difference and you prolly gain more from the intake design than the flow would hurt you.

jwick · 12-28-2018, 06:48 PM

Quote:

Originally Posted by Jinxx

I was thinking from most of the other turbo kits just the difference from their location going to the stock location ... to add this manifold to a existing kit ... you would add 4 90 degree elbows ... I guess it wouldnt be a big difference and you prolly gain more from the intake design than the flow would hurt you.

You could just buy a new intercooler and eliminate that issue.

phunk · 12-28-2018, 07:12 PM

Ya it won’t make any difference. You’d want to toss all the upper piping any kit came with and start from scratch. You can go straight through the core supports like we do then behind the rad right into each throttle. All the other kits snake around the outter sides of the core support and fender liners and have a ton of bends anyway, so you can end up with something better off or certainly no worse than you already had. Although we don’t really see a reason to not just go over the top of the rad and make it much more tidy. All the core support components bolt in and out, so no permanent changes to the vehicle need to be made.

Jinxx · 12-28-2018, 07:44 PM

any idea how much performance over a ported upper and lower intake this would make ? ...those was seeing 30 ish hp/tq with a boosted car ...to convert over would be intake and new intercooler which would be 4.5kish ...granted it by far looks the best

jwick · 12-28-2018, 07:55 PM

Quote:

Originally Posted by Jinxx

any idea how much performance over a ported upper and lower intake this would make ? ...those was seeing 30 ish hp/tq with a boosted car ...to convert over would be intake and new intercooler which would be 4.5kish ...granted it by far looks the best

Is there a price listed for this manifold yet?

Cuz if your $4.5k doesn’t include the manifold, there’s no way it costs that must just to buy a new intercooler and intake piping over the radiator.

jwick · 12-28-2018, 07:56 PM

Phunk- Where are y’all putting the MAFs or would this have to be density tuned off a new MAP sensor?

Edit - stupid iPhone autocorrect

Jinxx · 12-28-2018, 07:59 PM

Quote:

Originally Posted by jwick

Is there a price listed for this manifold yet?

Cuz if your $4.5k doesn’t include the manifold, there’s no way it costs that must just to buy a new intercooler and intake piping over the radiator.

In this thread he said the intake was 3k ...and if you replace the intercooler to match it I would assume 1200 ish .....then retuning etc ....this would be a pricy upgrade over a ported upper and lower if the performance gains are similar

12-28-2018, 02:46 PM	#76 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	__________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

12-28-2018, 05:27 PM	#80 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,507 Drives: 2013 Nismo 370z Rep Power: 2684391	Those pictures make sense. Just a redo of the intercooler for the piping to come out the top. Last edited by Spooler; 12-28-2018 at 06:32 PM.

12-28-2018, 05:52 PM	#81 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 34,859 Drives: 2011 Nismo GM 6M Rep Power: 2684436	__________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

12-28-2018, 06:32 PM	#83 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,507 Drives: 2013 Nismo 370z Rep Power: 2684391	I can't wait to see Justin's car up and running with the new intake/intercooler setup. Rusty likes this.

12-28-2018, 07:12 PM	#86 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,654 Drives: 370 Rep Power: 944523	Ya it won’t make any difference. You’d want to toss all the upper piping any kit came with and start from scratch. You can go straight through the core supports like we do then behind the rad right into each throttle. All the other kits snake around the outter sides of the core support and fender liners and have a ton of bends anyway, so you can end up with something better off or certainly no worse than you already had. Although we don’t really see a reason to not just go over the top of the rad and make it much more tidy. All the core support components bolt in and out, so no permanent changes to the vehicle need to be made. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

12-28-2018, 05:09 PM	#78 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	I am curious...with the throttle bodies in the front you would have to have 90 degree couplers there and another set of 90 degree couplers to get down into the intercooler ....wouldn’t they be more restrictive to the flow than the OEM manifold ...even with a NA setup with filters located there the 90 degree bend would have to restrict flow over the OEM set up.

12-28-2018, 07:44 PM	#87 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	any idea how much performance over a ported upper and lower intake this would make ? ...those was seeing 30 ish hp/tq with a boosted car ...to convert over would be intake and new intercooler which would be 4.5kish ...granted it by far looks the best

12-28-2018, 07:56 PM	#89 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	CJM Billet Intake Manifold Phunk- Where are y’all putting the MAFs or would this have to be density tuned off a new MAP sensor? Edit - stupid iPhone autocorrect __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build Last edited by jwick; 12-29-2018 at 12:32 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AAM Intake Manifold	mults	Intake/Exhaust	81	11-26-2018 07:14 AM
[FOR SALE] (BNIB) OEM Intake Manifold Gaskets///Exhaust Manifold Gaskets	BlkNismo	Parts for sale (Private Classifieds)	19	08-13-2016 12:01 PM
selling used stillen G3 intake.Motordyne M370 Intake Manifold	01206	Canada	4	04-14-2016 01:31 AM
intake plenum vs intake manifold?	louiey370z	Engine & Drivetrain	5	01-07-2016 09:49 AM
Billet intake manifold	Elmo370z	Engine & Drivetrain	46	10-04-2015 10:16 AM