Radiator: CSF or Mishimoto?

redondoaveb · 12-28-2017, 10:33 AM

Quote:

Originally Posted by jwick

That’s the one

Ordered and shipped.

sirnixalot · 12-28-2017, 12:30 PM

any reason you guys don't feel like removing the thermostat housing, drill and tap, place sensor there?

would look so much cleaner, not create more failure points and achieve the same result?

jwick · 12-28-2017, 02:11 PM

I’d rather have a purpose made piece than drilling a cast piece. I’m also a function over appearance guy.

Rusty · 12-28-2017, 03:05 PM

Quote:

Originally Posted by jwick

I’d rather have a purpose made piece than drilling a cast piece. I’m also a function over appearance guy.

Plus there is no good place to drill and tap on the housing. Not enough room and it's too thin for threads.

phunk · 12-28-2017, 03:32 PM

Quote:

Originally Posted by Rusty

Plus there is no good place to drill and tap on the housing. Not enough room and it's too thin for threads.

time for new billet product... ?

Rusty · 12-28-2017, 03:51 PM

Quote:

Originally Posted by phunk

time for new billet product... ?

I like your thinking.

Something with a lower temp, and a place for a sensor.

Rusty · 12-28-2017, 06:00 PM

Quote:

Originally Posted by Rusty

Plus there is no good place to drill and tap on the housing. Not enough room and it's too thin for threads.

Quote:

Originally Posted by phunk

time for new billet product... ?

Quote:

Originally Posted by Rusty

I like your thinking.

Something with a lower temp, and a place for a sensor.

The wheels must be turning. I smell smoke from Chicago.

sirnixalot · 12-28-2017, 07:09 PM

Quote:

Originally Posted by phunk

time for new billet product... ?

something like the spacer they have for the sr20?

for example
https://au.gktech.com/sr20-coolant-neck-spacer

phunk · 12-31-2017, 08:23 PM

The thermostat spacer is clever but it’s not standard to measure coolant temps after the rad instead of before it. The stock sensors are on the water outlet housing on the rear of the engine. The thermostat area will give you water temps after the rad already cooled, or water inlet temp.

Seems like the easiest place to put the sensor would be the water housing at the front of the engine on the timing cover. Unless you wanted to be super clean and remove the rear water housing from the heads to weld a bung on.

Pretty soon I have to make a billet front water housing anyway (one that clears our front throttle intake manifold), so I’ll keep this thread in mind when starting that project.

Rusty · 12-31-2017, 09:10 PM

Quote:

Originally Posted by phunk

The thermostat spacer is clever but it’s not standard to measure coolant temps after the rad instead of before it. The stock sensors are on the water outlet housing on the rear of the engine. The thermostat area will give you water temps after the rad already cooled, or water inlet temp.

Seems like the easiest place to put the sensor would be the water housing at the front of the engine on the timing cover. Unless you wanted to be super clean and remove the rear water housing from the heads to weld a bung on.

Pretty soon I have to make a billet front water housing anyway (one that clears our front throttle intake manifold), so I’ll keep this thread in mind when starting that project.

You got me confused.

The thermostat is before the radiator, not after. So if the sensor is on the thermostat housing or the upper hose. It will take the reading before the rad. Not after like you explained.

BGTV8 · 01-01-2018, 01:20 AM

Quote:

Originally Posted by Rusty

You got me confused.

The thermostat is before the radiator, not after. So if the sensor is on the thermostat housing or the upper hose. It will take the reading before the rad. Not after like you explained.

I agree ............ thermostat spacer would do the job .......

Charles - I'm hot to trot ........ let me know when you have this done ..........

phunk · 01-01-2018, 04:58 AM

Just for the sake of eliminating any doubt....

Rusty · 01-01-2018, 07:05 AM

Quote:

Originally Posted by phunk

Just for the sake of eliminating any doubt....

Diagram is wrong. That is the first time I ever seen the thermostat AFTER the rad. It's always before.

phunk · 01-01-2018, 07:30 AM

Additional text from Nissan so that you don’t have to take my word for it. Notice what is referred to as the water inlet, and what is referred to as the water outlet. Also consider where the factory temp sensor is, and where it is not.

BGTV8 · 01-01-2018, 02:08 PM

Argghhh .... cr4p ................

12-28-2017, 12:30 PM	#197 (permalink)
sirnixalot Track Member Join Date: May 2017 Location: Cayman Islands Posts: 685 Drives: 2010 370Z Rep Power: 57453	any reason you guys don't feel like removing the thermostat housing, drill and tap, place sensor there? would look so much cleaner, not create more failure points and achieve the same result? __________________ 2010 Sport - LS3 swap loading 2012 Frontier - BTWTuning VK56DE swap

12-28-2017, 02:11 PM	#198 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	I’d rather have a purpose made piece than drilling a cast piece. I’m also a function over appearance guy. Hotrodz likes this. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

12-31-2017, 08:23 PM	#204 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,655 Drives: 370 Rep Power: 944523	The thermostat spacer is clever but it’s not standard to measure coolant temps after the rad instead of before it. The stock sensors are on the water outlet housing on the rear of the engine. The thermostat area will give you water temps after the rad already cooled, or water inlet temp. Seems like the easiest place to put the sensor would be the water housing at the front of the engine on the timing cover. Unless you wanted to be super clean and remove the rear water housing from the heads to weld a bung on. Pretty soon I have to make a billet front water housing anyway (one that clears our front throttle intake manifold), so I’ll keep this thread in mind when starting that project. GaleForce and redondoaveb like this. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Mishimoto Performance Aluminum Radiator now in stock at B2autodesigns	b2autodesigns	Drivetrain/Engine	265	06-07-2019 08:41 AM
Mishimoto Releases Nissan 370Z Radiator	Mishimoto	Drivetrain/Engine	1	03-18-2013 04:44 PM
[FOR SALE] New Mishimoto Radiator Hose Kit - Red	Gixxer-370Z	Parts for sale (Private Classifieds)	11	04-02-2012 12:48 PM
Mishimoto Radiator Hoses ON SALE at Imported Performance	Imported Performance	Drivetrain/Engine	395	10-25-2011 05:02 PM

01-01-2018, 02:08 PM	#210 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,503 Drives: 09 Nissan 370Z M6 Rep Power: 29907	Argghhh .... cr4p ................