UpRev ECU tune results for Semtex's Z

Zeto · 10-29-2009, 06:39 AM

In for updates.

LiquidZ · 10-29-2009, 07:00 AM

Quote:

Originally Posted by damomck

Oops, sorry my bad - the dyno graphs didn't show up on the computer at work and have just had a gander at them at home. Looks like you've gained a heap of torque below 3250rpms, that alone is worth getting the tune done.

I agree! It looks like he gained that torque back from the Stillen header install.

semtex · 10-29-2009, 07:21 AM

Quote:

Originally Posted by LiquidZ

I agree! It looks like he gained that torque back from the Stillen header install.

Hmm...I'm not 100% sure on the low-end torque gain. From the graph, it kinda looks like Sharif went WOT at an earlier rpm on the two post-tune runs than he did on the baseline run. About 500 rpm earlier, actually. That alone might account for the higher torque at 3000 rpm; the engine was simply spooled up already at that point. On the other hand, a real gain in low-end torque would account for my butt-dyno impressions.

RCZ · 10-29-2009, 07:46 AM

I am sure you have better response from more aggressive throttle mapping...thats probably why it seems like he went WOT earlier.

Semtex: Did you guys talk about that 8,000RPM limit at all? Advised against it?

semtex · 10-29-2009, 08:01 AM

He bumped it up to 8000, said I can use it at my discretion. He didn't run all the way to 8000 on the dyno though, I'm noticing.

Zeto · 10-29-2009, 08:29 AM

Quote:

Originally Posted by semtex

He bumped it up to 8000, said I can use it at my discretion. He didn't run all the way to 8000 on the dyno though, I'm noticing.

Do you think there might have been more power to be had had he gone up to 8000 RPMS?

HKYStormFront · 10-29-2009, 08:40 AM

Quote:

Originally Posted by Zeto

Do you think there might have been more power to be had had he gone up to 8000 RPMS?

if the torque # stayed the same and didn't fall off, hp would go up yes

RCZ · 10-29-2009, 09:10 AM

Torque is falling off near the end of the run though, so I doubt it would have benefited too much from running it into the 8k redline. I think they were wise and decided to leave the top end a little tame in order to increase longevity.

semtex · 10-29-2009, 09:12 AM

DynoJet run scheduled for 1pm ET tomorrow (Friday). Will post results as soon as I get them.

370Zsteve · 10-29-2009, 09:16 AM

Quote:

Originally Posted by semtex

He bumped it up to 8000, said I can use it at my discretion. He didn't run all the way to 8000 on the dyno though, I'm noticing.

He didn't want to melt the engine, felt that could be left up to you!

semtex · 10-29-2009, 09:47 AM

Quote:

Originally Posted by RCZ

320whp out of an NA V6 on a dyno dynamics is amazing semtex, nothing to sneeze at. I'm going to get tuned on the same MustangDyne Dyno I got 310whp (HPLogic) on. According to your theory I should only pick up a few hp.. maximum maybe 10whp?

I think you have the strongest N/A car on the boards, congrats...for now. Don't pop the champ till Sat

I think Phimosis actually has the highest numbers on the board for an NA car right now -- 343whp. Induction parts + ECU reflash dyno results

370Zsteve · 10-29-2009, 09:49 AM

Quote:

Originally Posted by semtex

I think Phimosis actually has the highest numbers on the board for an NA car right now -- 343whp. Induction parts + ECU reflash dyno results

343whp =

Just looked at his dyno graph...he removed the mufflers and was getting over 300whp stock? Sounds like an awfully high baseline to start with, all subsequent #'s suspect? Sorry if this has been rehashed before, I realize it's an old thread.

semtex · 10-29-2009, 10:02 AM

Quote:

Originally Posted by 370Zsteve

343whp =

Just looked at his dyno graph...he removed the mufflers and was getting over 300whp stock? Sounds like an awfully high baseline to start with, all subsequent #'s suspect? Sorry if this has been rehashed before, I realize it's an old thread.

Right . . . I'm not all that familiar with the dyno he did his tuning on, and I don't really want to get into a debate about the 'worthiness' of his numbers. Threads like that don't typically end well, people get bent out of shape, etc.

I'm just pointing out that there are other NA cars on this forum posting good numbers. Let's leave it at that.

Whtfairladyz · 10-29-2009, 02:30 PM

How did Sharif up the rev limiter? From what I understand from reading on here and talking to the guys at UpRev, you can't do that?

From watching my two buddy's dyno pulls with their Z's, they all shut down at around 7500 rpm.

Uprev · 10-29-2009, 04:47 PM

Quote:

Originally Posted by RCZ

I am sure you have better response from more aggressive throttle mapping...thats probably why it seems like he went WOT earlier.

Semtex: Did you guys talk about that 8,000RPM limit at all? Advised against it?

We don't touch throttle mapping on the VHR motors. They already do WOT from a dead stop.

10-29-2009, 08:01 AM	#20 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 33	He bumped it up to 8000, said I can use it at my discretion. He didn't run all the way to 8000 on the dyno though, I'm noticing. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

10-29-2009, 09:12 AM	#24 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 33	DynoJet run scheduled for 1pm ET tomorrow (Friday). Will post results as soon as I get them. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Semtex's Monterey Blue 370Z	semtex	Member's 370Z Gallery	235	06-21-2013 12:49 AM
Cobb vs UpRev	FricFrac	Tuning	183	11-05-2009 05:14 PM
UpRev still coming out for the 370Z	FricFrac	Tuning	2	08-22-2009 07:32 AM
UpRev development status	semtex	Tuning	12	07-13-2009 11:34 AM
Semtex, RCZ... What gear on the dyno	DannyGT	Engine & Drivetrain	14	04-14-2009 01:07 PM

10-29-2009, 06:39 AM	#16 (permalink)
Zeto Track Member Join Date: Apr 2009 Location: North NJ Age: 41 Posts: 766 Drives: 09 Pearl White 370Z Rep Power: 268	In for updates.

10-29-2009, 07:46 AM	#19 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	I am sure you have better response from more aggressive throttle mapping...thats probably why it seems like he went WOT earlier. Semtex: Did you guys talk about that 8,000RPM limit at all? Advised against it?

10-29-2009, 09:10 AM	#23 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	Torque is falling off near the end of the run though, so I doubt it would have benefited too much from running it into the 8k redline. I think they were wise and decided to leave the top end a little tame in order to increase longevity.

10-29-2009, 02:30 PM	#29 (permalink)
Whtfairladyz Base Member Join Date: Jun 2009 Location: Winchester, TN Posts: 77 Drives: '92 Nissan 300zx Rep Power: 267	How did Sharif up the rev limiter? From what I understand from reading on here and talking to the guys at UpRev, you can't do that? From watching my two buddy's dyno pulls with their Z's, they all shut down at around 7500 rpm.