370Z who have already been tuned - post data if poss?

Kastley85891 · 11-18-2009, 12:39 PM

Could you list up your mods, your base WHP / WTRQ and final HP/TQ figures, also a list of mods.

Data I am after is...
IDC (injector Duty cycle)
MAF Feedback (V)
MAF flow (g/s)
Total timing (degs)
IAT (intake air temps)
AFR (air fuel ratio) WB if avaliable.

Thats it, not looking to reverse engineer anything here, just looking at some future plans and gaining some insight.

jpit · 11-18-2009, 01:26 PM

My tune achieved 299.3 rwhp and 243.2 torque and I started at 283.2 hp and 235.3 torque (all SAE corrected). The dyno was done on a dynojet 248 in 4th gear. 5th gear was tried but ran into two problems: 5th gear brings the speed close to 160 (especially when the rev limit is changed) and this dyno only goes to 150 and uprev recommended 4th gear as the dyno puts too much load onto the 5th gear.

My observations: Dynoing really isn't an exact science as heat soak (especially in aluminum engines) starts almost right away and can throw everything off. So unless you have the time to let the the engine cool for at least 30 minutes between runs I believe the readings will be off somewhat.

My mods: Berk HFCs, R2C intake with Modshack vent mod, and smaller, lighter crank. The Modshack vent mod is great and intake air temps are never more than 8 degrees above the ambient temp.

Kastley85891 · 11-18-2009, 01:34 PM

Thanks jpit - do you have any log data to go with your pulls? especially the items in original post?
Thx

jpit · 11-18-2009, 03:35 PM

I have a program that can read that data through the obd port but that was being used by the tuner and I am not sure if it is available to him while he is tuning. I assume the ignition advance is. As far as the a/f ratio is concerned the tuned version starts out at 13.5 (3500) and goes gradually down to 12.5 (5000) and stays there right up to 7500. The stock a/f started out at 12.5 and goes below 12 at 5000 and gradually down to 11 at 7300. The graph is posted somewhere in this forum.

RCZ · 11-18-2009, 06:54 PM

I dont think you will be able to get the data you are after....very few people datalog, and of those people, even fewer will take the time to post the info. If you get one full post of that info, I'd be thrilled.

Kastley85891 · 11-22-2009, 07:58 PM

ok guys, any one got there max injector duty cycle at 6500 rpm + anything toward redline ?
Any tuners want to chime in with IDC on these vehicles?
Appreciate.

chameleon · 11-22-2009, 10:34 PM

any type of real tuning is not yet widely available for the VQ37VHR.. so unfortunately no one is going to be able to provide that data to you. I have been working on a project/customer car which I have logged some runs on the dyno and it can be a great reference as far as modding goes. I need to organize and edit the entire thing and I will have it posted up within this week. stay tuned.

Kastley85891 · 11-22-2009, 10:58 PM

chameleon
Yep - you got my issue right on the head, so limited and so few with capability.
Really appreciate the log data when you get it up, I am trying to get a head start on my E85 VQ ideas.
Cheers

Kastley85891 · 11-25-2009, 01:57 PM

Any updates Chameleon?

11-18-2009, 12:39 PM	#1 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	370Z who have already been tuned - post data if poss? Could you list up your mods, your base WHP / WTRQ and final HP/TQ figures, also a list of mods. Data I am after is... IDC (injector Duty cycle) MAF Feedback (V) MAF flow (g/s) Total timing (degs) IAT (intake air temps) AFR (air fuel ratio) WB if avaliable. Thats it, not looking to reverse engineer anything here, just looking at some future plans and gaining some insight.

11-22-2009, 10:34 PM	#7 (permalink)
chameleon Base Member Join Date: May 2009 Location: new york Posts: 19 Drives: G37S Rep Power: 15	any type of real tuning is not yet widely available for the VQ37VHR.. so unfortunately no one is going to be able to provide that data to you. I have been working on a project/customer car which I have logged some runs on the dyno and it can be a great reference as far as modding goes. I need to organize and edit the entire thing and I will have it posted up within this week. stay tuned. __________________ Race Technician - NoLimitMotorSport.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
370Z Exhaust Sound Clip data base	Minicobra1	Intake/Exhaust	383	04-26-2021 10:47 AM
Anyone know more about the EVENT DATA RECORDER ?	chubbs	Nissan 370Z General Discussions	26	10-05-2010 03:35 PM
Data logging MAF settings with Cobb AccessPort	Denny McLain	Tuning	8	11-09-2009 08:52 AM
350z / 370z Event Data Recorder (EDR)	05_350Z	Nissan 370Z General Discussions	11	08-25-2009 11:15 AM
TUNED 370Z'S and 350Zs AT TOKYO AUTO SALON	AK370Z	Nissan 370Z Photos / Spyshots / Video / Media Gallery	11	01-27-2009 08:26 PM

11-18-2009, 01:26 PM	#2 (permalink)
jpit Enthusiast Member Join Date: Feb 2009 Location: Washington State Posts: 440 Drives: 370Z Tour MT w/Spt Rep Power: 16	My tune achieved 299.3 rwhp and 243.2 torque and I started at 283.2 hp and 235.3 torque (all SAE corrected). The dyno was done on a dynojet 248 in 4th gear. 5th gear was tried but ran into two problems: 5th gear brings the speed close to 160 (especially when the rev limit is changed) and this dyno only goes to 150 and uprev recommended 4th gear as the dyno puts too much load onto the 5th gear. My observations: Dynoing really isn't an exact science as heat soak (especially in aluminum engines) starts almost right away and can throw everything off. So unless you have the time to let the the engine cool for at least 30 minutes between runs I believe the readings will be off somewhat. My mods: Berk HFCs, R2C intake with Modshack vent mod, and smaller, lighter crank. The Modshack vent mod is great and intake air temps are never more than 8 degrees above the ambient temp.

11-18-2009, 01:34 PM	#3 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	Thanks jpit - do you have any log data to go with your pulls? especially the items in original post? Thx

11-18-2009, 03:35 PM	#4 (permalink)
jpit Enthusiast Member Join Date: Feb 2009 Location: Washington State Posts: 440 Drives: 370Z Tour MT w/Spt Rep Power: 16	I have a program that can read that data through the obd port but that was being used by the tuner and I am not sure if it is available to him while he is tuning. I assume the ignition advance is. As far as the a/f ratio is concerned the tuned version starts out at 13.5 (3500) and goes gradually down to 12.5 (5000) and stays there right up to 7500. The stock a/f started out at 12.5 and goes below 12 at 5000 and gradually down to 11 at 7300. The graph is posted somewhere in this forum.

11-18-2009, 06:54 PM	#5 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1118	I dont think you will be able to get the data you are after....very few people datalog, and of those people, even fewer will take the time to post the info. If you get one full post of that info, I'd be thrilled.

11-22-2009, 07:58 PM	#6 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	ok guys, any one got there max injector duty cycle at 6500 rpm + anything toward redline ? Any tuners want to chime in with IDC on these vehicles? Appreciate.

11-22-2009, 10:58 PM	#8 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	chameleon Yep - you got my issue right on the head, so limited and so few with capability. Really appreciate the log data when you get it up, I am trying to get a head start on my E85 VQ ideas. Cheers

11-25-2009, 01:57 PM	#9 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	Any updates Chameleon?