Nissan 370Z Forum  

What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

Installed the iJDMTOY rear tail/brake/reverse lights in my 2016 roadster this weekend. I opted for the smoked lens version. Just personal preference over the red. There are plenty of other

Go Back   Nissan 370Z Forum > Nissan 370Z General Area > Nissan 370Z General Discussions


Like Tree16483Likes

 
 
LinkBack Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 06-14-2017, 02:19 AM   #11 (permalink)
Base Member
 
cubsfan51's Avatar
 
Join Date: Jan 2017
Location: Chicago. IL
Age: 74
Posts: 42
Drives: 16 Rdstr TS M6 Blue
Rep Power: 6738
cubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond reputecubsfan51 has a reputation beyond repute
Default

Installed the iJDMTOY rear tail/brake/reverse lights in my 2016 roadster this weekend. I opted for the smoked lens version. Just personal preference over the red. There are plenty of other posts on this forum with pics and videos on this install which were very helpful to look at before I started. I also felt no need to duplicate that effort, so I didn’t take my own pics of the process. And please, SOLDER ALL CONNECTIONS! The two minutes of your life it takes to do it right can save you hours of grief later. First things I did were to add a small bead of silicone sealer around the seam where the body of the unit attaches to the lens. This was based solely on other posters mentioning condensation problems. At the same time, I soaked the bolts of the original dummy reflector with Liquid Wrench to get past Loctite overuse from the factory. I Let both of these sit for 48 hours. Then, I got started.

I’m not sure if anyone else has put one of these into a Roadster, but there are some minor differences which makes this somewhat unique. The side panels in the trunk are different, but the removal/reinstallation process is the same, so no big deal there. The one challenge I ran into was the fact that since this is a fully enclosed trunk, there is the required glow-in-the-dark manual trunk release handle on the inside rear trunk panel. (Never mind how anyone could possibly get stuffed into that trunk!) This made removing that panel more difficult. There is a plastic mounting plate under the handle that snaps into place over the panel, and there is no way to release those snaps with the panel in place. I managed to muscle the panel off without damaging anything, but there was no way it was going back together the same way. With the panel removed and the handle and release cable removed from the mounting plate, I was able to get a pair of long-nosed pliers under the metal frame piece that the plate is mounted on. I was then able to squeeze the tabs to release the snaps and remove the plate. (I really apologize for not taking pics of this.) I could then reassemble the release cable, handle and mounting plate and snap it back into place after the rear panel was reinstalled. This little snafu added about 1.5 hours to my installation time.

Also, I wish iJDMTOY would run the sheath over the wires farther up the bundle. I was about done with the install before I realized how much loose wire would be dangling without that additional protection. I wasn’t about to undo it all to wrap it higher up at that point.

So with 20/20 hindsight, here’s what I would have done differently: 1) Sheath the wire bundle with heat-shrink tubing or electrical tape to within a few inches of the wire ends. 2) Loosen, but not remove, the rear interior trunk panel. 3) Tap into the right side tail light assembly rather than the left. Since the trunk release handle is on the left side, this would allow more wiggle room to work with a loosened rear panel. There are also better opportunities to secure the wire bundle on the right underside with other parts of the wiring harness on that side.

Here are some post-install pics, although I now realize pics of the release cable/handle/mounting plate would have been more useful.
Attached Images
File Type: jpg Off.jpg (64.0 KB, 55 views)
File Type: jpg Tail Light.jpg (65.3 KB, 52 views)
File Type: jpg Brake Light.jpg (64.4 KB, 51 views)
File Type: jpg Reverse Light.jpg (63.5 KB, 49 views)
File Type: jpg Trunk Panels.jpg (85.5 KB, 54 views)
File Type: jpg Trunk Release.jpg (114.1 KB, 62 views)
cubsfan51 is offline   Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
[MAZOC] Official "Off-Topic" Discussion Thread m4a1mustang MAZOC 6670 09-06-2018 07:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY) AK370Z Nissan 370Z General Discussions 10007 06-08-2017 09:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV eastwest2300 The Lounge (Off Topic) 10005 09-11-2015 08:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY) AK370Z Nissan 370Z General Discussions 10148 06-19-2014 08:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII JARblue The Lounge (Off Topic) 10016 11-10-2013 11:21 AM


All times are GMT -5. The time now is 04:49 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2