GaleForce's build

Mr&Mrs · 03-12-2013, 05:28 PM

It isnt a type of seal you can go too tight with is it? Like a kitchen sink gasket, you pinch those a little, water leak! Maybe the same deal with those? Sometimes tighter is not always better.

GaleForce · 03-12-2013, 05:29 PM

Quote:

Originally Posted by Mitco39

I think I am going to have leaks in the lines coming off the relocation plate as well. I got them to stop at idle but wont know for sure until I take mine for a spin. They are damn tight thats for sure, hopefully they seat and stop leaking.

The only leak I had at during the first start test was the output fitting from the oil relocation plate. They were pre-installed and I didn't bother checking them. Fixed that, now the hose fitting at the same location leaks (where the red elbow meets the blue nut), and like yours, fine at idle. I'll be taking some oil with me on my first real drive.

Mitco39 · 03-12-2013, 07:19 PM

I just got back from a quick drive to the car wash with mine, no oil on the ground after letting it idle for 15 mins after driving it. Fingers crossed. Also eyeballing a alignment is not a good idea in the Z, lol felt like ice the whole time. Gotta get it into get aligned soon here.

Baer383 · 03-12-2013, 07:38 PM

Quote:

Originally Posted by GaleForce

Yes I have Whitelines. They come with clip on lateral locks and mine stayed where they were supposed to while using them. These optional lateral locks are cheap insurance to make sure the bar doesn't move more than 3-4mm.

I just put Whiteline front and rear bars and those lateral locks with the allen bolts came included for the front & rear.

GaleForce · 03-12-2013, 09:18 PM

Quote:

Originally Posted by Baer383

I just put Whiteline front and rear bars and those lateral locks with the allen bolts came included for the front & rear.

Maybe they include them with the new ones? I have had my sway bars for a while. The fronts had the proper locks, but the rear had the simple locks. No biggie, Jomer at Fred Beans gave me a heck of a deal so it's all good

LMBmikeZ · 03-12-2013, 09:19 PM

Fred Beans FTW I have been using them for my past few orders, always great deals and service

ENT-Z · 03-13-2013, 06:08 PM

Quote:

Originally Posted by GaleForce

Maybe they include them with the new ones? I have had my sway bars for a while. The fronts had the proper locks, but the rear had the simple locks. No biggie, Jomer at Fred Beans gave me a heck of a deal so it's all good

Must be because I only have the clip on versions and the definitely didn't keep the bar in place. If it wasn't for the diff stopping it I think it would have snapped the stock end link off!

GaleForce · 03-14-2013, 08:36 PM

Small update,

Yesterday at the exhaust shop,

Today, some body work,

This stuff would be easier if I knew what the heck I was doing

LMBmikeZ · 03-14-2013, 08:42 PM

that's funny, you make it all seem so easy

looking good!

simota1 · 03-14-2013, 09:00 PM

good job man... you know for the skirt i used windshield glue and glued the hell outa it so it would sit flush... great idea with reshaping it and making it flush that way by slitting the FG and re glassing it

simota1 · 03-14-2013, 09:00 PM

btw bro if thats your house garage your my god lol....

LMBmikeZ · 03-14-2013, 09:05 PM

Quote:

Originally Posted by simota1

btw bro if thats your house garage your my god lol....

Are you referring to the first pic? That's at the exhaust shop

GaleForce · 03-14-2013, 09:06 PM

Quote:

Originally Posted by simota1

good job man... you know for the skirt i used windshield glue and glued the hell outa it so it would sit flush... great idea with reshaping it and making it flush that way by slitting the FG and re glassing it

Yeah, I could have used fast setting panel bond and been done with it but... its a bitch to remove the skirt if you have to down the road. This way I'll be able to remove the skirts incase I need to take the car in for service.

Quote:

Originally Posted by simota1

btw bro if thats your house garage your my god lol....

I wish the first picture was my own garage. Some day

simota1 · 03-14-2013, 09:08 PM

Quote:

Originally Posted by LMBmikeZ

Are you referring to the first pic? That's at the exhaust shop

ahh lol i missed that..... i didnt bother reading the first sentence the picture took my attention right away... i was like holey hell man

what the heck do these guys do for a living? thats a man cave right there....

i still gotta jack my car up each time i work on it

simota1 · 03-14-2013, 09:09 PM

Quote:

Originally Posted by GaleForce

Yeah, I could have used fast setting panel bond and been done with it but... its a bitch to remove the skirt if you have to down the road. This way I'll be able to remove the skirts incase I need to take the car in for service.

I wish the first picture was my own garage. Some day

your hella right about removing the skirt lol.... it was a pain to take mine out and do my fenders... i wish i would have thought of your technique man....

felt like i was gonna tear my skirt separating it from my car

03-12-2013, 05:28 PM	#526 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,192 Drives: RZ34 Rep Power: 15161	It isnt a type of seal you can go too tight with is it? Like a kitchen sink gasket, you pinch those a little, water leak! Maybe the same deal with those? Sometimes tighter is not always better. __________________ Project Z <--Click - Check out the link too many mods to list!

03-12-2013, 07:19 PM	#528 (permalink)
Mitco39 A True Z Fanatic Join Date: Aug 2012 Location: Edmonton Alberta Canada Posts: 2,089 Drives: 40th 370z Rep Power: 131	I just got back from a quick drive to the car wash with mine, no oil on the ground after letting it idle for 15 mins after driving it. Fingers crossed. Also eyeballing a alignment is not a good idea in the Z, lol felt like ice the whole time. Gotta get it into get aligned soon here. wheee! and GaleForce like this. __________________ 2007 Chevy Duramax - EFILive Tuned By Me 2010 40th W/ Nav - Boosted Performance - UpRev Tuned By Me The Mrs. Ride -2012 335XI N55 BMW - Cobb Tuned By Me, Built by her My Build --> http://www.the370z.com/members-370z-...39s-build.html

03-12-2013, 09:19 PM	#531 (permalink)
LMBmikeZ A True Z Fanatic Join Date: May 2010 Location: Ontario, Canada Posts: 12,237 Drives: 40th Rep Power: 10349	Fred Beans FTW I have been using them for my past few orders, always great deals and service GaleForce likes this. __________________ CUSTOM NISMO \| BERK \| H&R \| STANCE \| SPL everything \| EVO-R \| 34 Setrab \| WHITELINE \| Redline \| Carkitcompany \| Zspeed \| UpRev \| SEIBON

03-14-2013, 08:36 PM	#533 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51864	Small update, Yesterday at the exhaust shop, Today, some body work, This stuff would be easier if I knew what the heck I was doing wheee! and zefaulter like this. __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

03-14-2013, 08:42 PM	#534 (permalink)
LMBmikeZ A True Z Fanatic Join Date: May 2010 Location: Ontario, Canada Posts: 12,237 Drives: 40th Rep Power: 10349	that's funny, you make it all seem so easy looking good! simota1 and GaleForce like this. __________________ CUSTOM NISMO \| BERK \| H&R \| STANCE \| SPL everything \| EVO-R \| 34 Setrab \| WHITELINE \| Redline \| Carkitcompany \| Zspeed \| UpRev \| SEIBON

03-14-2013, 09:00 PM	#535 (permalink)
simota1 A True Z Fanatic Join Date: May 2009 Location: Dededo, Guam Posts: 6,642 Drives: solid red 370z 6mt Rep Power: 404	good job man... you know for the skirt i used windshield glue and glued the hell outa it so it would sit flush... great idea with reshaping it and making it flush that way by slitting the FG and re glassing it wheee! likes this. __________________ *TOP SECRET/POWERHOUSE AMUSE/ARC/DAYTONA RACING/VARIS/MINES/GANADOR/J-LINE/WORK EMOTION CR KAI/GT SPEC/CARBON SIGNAL/ZOOM ENGINEERING/ CARBON FIBER ELEMENT/STILLEN/*

03-14-2013, 09:00 PM	#536 (permalink)
simota1 A True Z Fanatic Join Date: May 2009 Location: Dededo, Guam Posts: 6,642 Drives: solid red 370z 6mt Rep Power: 404	btw bro if thats your house garage your my god lol.... __________________ *TOP SECRET/POWERHOUSE AMUSE/ARC/DAYTONA RACING/VARIS/MINES/GANADOR/J-LINE/WORK EMOTION CR KAI/GT SPEC/CARBON SIGNAL/ZOOM ENGINEERING/ CARBON FIBER ELEMENT/STILLEN/*

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My Z Build	pwrhsms	Member's 370Z Gallery	43	09-09-2013 11:35 AM
Possible Nos build	triadz	Forced Induction	7	04-06-2012 10:30 AM
TT build in Fl	travnflorida	Nissan 370Z General Discussions	3	08-15-2011 05:51 PM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 05:24 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 12:40 AM