Custom 3D Printed GTR Style Intake Plenum Project

ANMVQ · 02-28-2018, 02:11 PM

second."if" there is power the NA guys

Elmo370z · 03-04-2018, 12:18 AM

Quote:

Originally Posted by ANMVQ

second."if" there is power the NA guys

NA gains will be minimal with these manifolds, if you're not increasing the rev limiter with supporting mods and bumping up the compression it may not be worth the money. Some guy on here did the aam manifold on his NA set up and gains were not worth the money.

Hotrodz · 03-04-2018, 09:16 AM

Quote:

Originally Posted by Elmo370z

NA gains will be minimal with these manifolds, if you're not increasing the rev limiter with supporting mods and bumping up the compression it may not be worth the money. Some guy on here did the aam manifold on his NA set up and gains were not worth the money.

On that same point, it probably won't be worth it on a turbo charged or supercharged motor that is not built as well. I say this because the gains with the other two manifold conversions show great low end and mid range outputs. On a stock block the oem manifold is good enough on the bottom end. My motor is at 560tq and because of that my top end on whp is limited. Seb told me it would make significantly more whp but he can't keep the tq down to do so. Adding a upper manifold at this point would not provide any real benefit other than esthetics.

Sent from my SM-N910P using Tapatalk

jwick · 03-04-2018, 09:43 AM

Quote:

Originally Posted by Hotrodz

On that same point, it probably won't be worth it on a turbo charged or supercharged motor that is not built as well. I say this because the gains with the other two manifold conversions show great low end and mid range outputs. On a stock block the oem manifold is good enough on the bottom end. My motor is at 560tq and because of that my top end on whp is limited. Seb told me it would make significantly more whp but he can't keep the tq down to do so. Adding a upper manifold at this point would not provide any real benefit other than esthetics.

Sent from my SM-N910P using Tapatalk

I agree. Making power is not an issue with my current setup, the stock block is the limiting factor. I could easily turn the turbo up another 6-8 lbs but it would crater the engine. Unless you have a built block, there’s no reason to go chasing additional ponies other than you just like how it looks.

Elmo370z · 03-04-2018, 10:54 PM

Quote:

Originally Posted by Hotrodz

On that same point, it probably won't be worth it on a turbo charged or supercharged motor that is not built as well. I say this because the gains with the other two manifold conversions show great low end and mid range outputs. On a stock block the oem manifold is good enough on the bottom end. My motor is at 560tq and because of that my top end on whp is limited. Seb told me it would make significantly more whp but he can't keep the tq down to do so. Adding a upper manifold at this point would not provide any real benefit other than esthetics.

Sent from my SM-N910P using Tapatalk

Yup I agree. But from what I’ve read and correct me if I’m wrong. That this manifold will be beneficial in all aspects of the rev range. I don’t think it will happen and agree 100% on what you’re stating.

Hotrodz · 03-05-2018, 07:02 AM

Quote:

Originally Posted by Elmo370z

Yup I agree. But from what I’ve read and correct me if I’m wrong. That this manifold will be beneficial in all aspects of the rev range. I don’t think it will happen and agree 100% on what you’re stating.

Regardless of the outputs, I have seen the Cpt's work and it is very high quality. He brings a reasonably priced functional and ascetically pleasing upgraded to the game. The more choices the better!

NorthStyle · 03-28-2018, 09:01 AM

Quote:

Originally Posted by Hotrodz

On that same point, it probably won't be worth it on a turbo charged or supercharged motor that is not built as well. I say this because the gains with the other two manifold conversions show great low end and mid range outputs. On a stock block the oem manifold is good enough on the bottom end. My motor is at 560tq and because of that my top end on whp is limited. Seb told me it would make significantly more whp but he can't keep the tq down to do so. Adding a upper manifold at this point would not provide any real benefit other than esthetics.

Sent from my SM-N910P using Tapatalk

You're still running the stock block? Jebus I thought yours was built lol

Hotrodz · 03-28-2018, 09:11 AM

Quote:

Originally Posted by NorthStyle

You're still running the stock block? Jebus I thought yours was built lol

All natural, stock block and internals for now!

Sent from my SM-N910P using Tapatalk

02-28-2018, 02:11 PM	#1 (permalink)
ANMVQ A True Z Fanatic Join Date: Mar 2011 Location: Framingham MA Posts: 2,732 Drives: 2014 Q50 AWD Rep Power: 20	second."if" there is power the NA guys __________________ 14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Z1 Upper Intake Plenum	RustyM2001	Parts for sale (Private Classifieds)	2	03-26-2017 12:10 AM
M370 to z1 intake plenum	Eighties Meta	Tuning	3	01-01-2017 11:01 AM
intake plenum vs intake manifold?	louiey370z	Engine & Drivetrain	5	01-07-2016 09:49 AM
WTB Lower intake plenum	photoguy1	Wanted	0	09-07-2015 05:11 PM
Custom manifold/plenum/TBs	ViCiouS	Intake/Exhaust	40	11-25-2014 02:04 PM