First top mount single turbo 370Z

98intrigue · 05-12-2011, 11:35 PM

Quote:

Originally Posted by Red__Zed

You figure the TB issue is related to using different intake tract lengths?

That is the culprit to the MAF maxing out, but we are not sure why it threw a code for a bad throttle body. It would make sense that since the driver's side MAF was getting about 20% more air than the passenger side MAF, maybe the driver's side throttle body was trying to compensate and open more than then it through a code and went into limp mode? But then why after hooking it all back together about 2 hours later, it ran fine...even after probably 5 dyno pulls?

Quote:

Originally Posted by Ryan@prosportGauges

im still wondering why not mount the MAF's before the Split to each TB!

Because then Shawn would have to modify both intake piping and relocate the BOV... if the upgraded MAFs don't work out, your idea will be the next step.

Jamaica · 05-12-2011, 11:49 PM

Looks good man.

ClemsonWill · 05-13-2011, 08:02 AM

Looks great! Definitely one of my favorite Zs on the forum! Can't wait to see more pictures and dyno results.

Prosport Gauges · 05-13-2011, 09:41 AM

Quote:

Originally Posted by 98intrigue

That is the culprit to the MAF maxing out, but we are not sure why it threw a code for a bad throttle body. It would make sense that since the driver's side MAF was getting about 20% more air than the passenger side MAF, maybe the driver's side throttle body was trying to compensate and open more than then it through a code and went into limp mode? But then why after hooking it all back together about 2 hours later, it ran fine...even after probably 5 dyno pulls?

Because then Shawn would have to modify both intake piping and relocate the BOV... if the upgraded MAFs don't work out, your idea will be the next step.

You can plum the BOV further down stream :P

98intrigue · 05-13-2011, 10:16 AM

Quote:

Originally Posted by Ryan@prosportGauges

You can plum the BOV further down stream :P

But it looks "cool" where it is, haha.

Prosport Gauges · 05-13-2011, 03:23 PM

Quote:

Originally Posted by A4RingedONE8T

Here's the 4.8psi graph

I just noticed the dotted line is the stated numbers, hp looks about 10-15 higher, closer to 440ish and tq is up near 400

bahaha i just notcied the TQ line looks like the 370z :P

ChipsWithDips · 05-13-2011, 04:15 PM

Quote:

Originally Posted by 98intrigue

That is the culprit to the MAF maxing out, but we are not sure why it threw a code for a bad throttle body. It would make sense that since the driver's side MAF was getting about 20% more air than the passenger side MAF, maybe the driver's side throttle body was trying to compensate and open more than then it through a code and went into limp mode? But then why after hooking it all back together about 2 hours later, it ran fine...even after probably 5 dyno pulls?

Yeah like I said, that MAF on the passenger side bend is not gonna be able to get an accurate reading. Think about it, the flow of air through a bend is not equal across the entire cross section of pipe. There's going to be a gradient of different flows throughout. The MAF only measures flow across it's hot filament which is only a specific point in that cross section. There's no way for it to get an accurate average of the entire cross sectional area.

Here's an example of how flow changes through just 30degrees of bend.

Quote:

im still wondering why not mount the MAF's before the Split to each TB!

if you did that they would be reading 2x as much flow each.

jran76 · 05-13-2011, 04:44 PM

Quote:

Originally Posted by ChipsWithDips

Yeah like I said, that MAF on the passenger side bend is not gonna be able to get an accurate reading. Think about it, the flow of air through a bend is not equal across the entire cross section of pipe. There's going to be a gradient of different flows throughout. The MAF only measures flow across it's hot filament which is only a specific point in that cross section. There's no way for it to get an accurate average of the entire cross sectional area.

Here's an example of how flow changes through just 30degrees of bend.

if you did that they would be reading 2x as much flow each.

I think you pretty much covered it. I really think the intake piping is going to have to be re-done in some way. I don't see any way around it. I honestly think something like the intercooler GTM uses on their SC kit would be the way to go. Of course, then you would have to do something different with the air filter on the turbo.... Easy for me to say....

A4RingedONE8T · 05-13-2011, 08:22 PM

Quote:

Originally Posted by ChipsWithDips

Yeah like I said, that MAF on the passenger side bend is not gonna be able to get an accurate reading. Think about it, the flow of air through a bend is not equal across the entire cross section of pipe. There's going to be a gradient of different flows throughout. The MAF only measures flow across it's hot filament which is only a specific point in that cross section. There's no way for it to get an accurate average of the entire cross sectional area.

Here's an example of how flow changes through just 30degrees of bend.

if you did that they would be reading 2x as much flow each.

Stock MAF's should be maxing out around 10-12psi, the passenger side MAF, on the radius, is NOT the problematic one. The one on the DRIVER'S side, the one on the straight piece of pipe, is the one that is maxed out. While your drawings may be true, the MAF on the radius is NOT what is causing the issue with Ryan's car. We already have a few different fixes if the upgraded MAF's do not get the car where Ryan wants it, no one needs to worry other than Ryan and myself. The injectors are also too small, they will be maxing out near if not before 500whp. Tuning with the two MAF's, as they are placed, was of no issue.

Kastley85891 · 05-13-2011, 09:35 PM

A one off build, to get as far as it did first shot is impressive... looking forward to the fully finished and tweaked up version. Dam to get this far in this time is amazing really... Good work

RCZ · 05-14-2011, 12:01 AM

Ryan, happy to help buddy. I think Making that kind of power at a low psi speaks volumes about the efficiency of the system. Get the bugs worked out and that thing will make some insane power.

I have an idea bout something you can do, I'll shoot you a message tomorrow.

Kingbaby · 05-14-2011, 02:22 AM

Wow...

Great numbers at insanely low psi!

Mr.Squeeze · 05-14-2011, 06:16 AM

Quote:

Originally Posted by A4RingedONE8T

Stock MAF's should be maxing out around 10-12psi, the passenger side MAF, on the radius, is NOT the problematic one. The one on the DRIVER'S side, the one on the straight piece of pipe, is the one that is maxed out. While your drawings may be true, the MAF on the radius is NOT what is causing the issue with Ryan's car. We already have a few different fixes if the upgraded MAF's do not get the car where Ryan wants it, no one needs to worry other than Ryan and myself. The injectors are also too small, they will be maxing out near if not before 500whp. Tuning with the two MAF's, as they are placed, was of no issue.

The HPX MAF's should work they wont peg. I am curious as to want kind of
injector pulse you guys had with the 600cc?

Boost_lee · 05-14-2011, 01:44 PM

i want 4.8 psi now!

98intrigue · 05-14-2011, 03:33 PM

The car is having some issues with oil temps and coolant temps. Even with a 25 row Setrab oil cooler, oil temps are 240-250 with shifting at 3k rpms and not boosting at all. I'm dropping the car off tomorrow and Shawn will see it Monday. He's going to see if he can mount the oil cooler in another location.

Today, my coolant was one dot away from the far right. I'm going to bleed the system and top off the coolant...hopefully, that will help. This seemed to be a common thing with 350Zs once the coolant system was opened up.

05-13-2011, 08:02 AM	#228 (permalink)
ClemsonWill A True Z Fanatic Join Date: Jul 2010 Location: Charleston, SC Posts: 12,045 Drives: a Civic VP! Rep Power: 444	Looks great! Definitely one of my favorite Zs on the forum! Can't wait to see more pictures and dyno results. __________________ Slightly modded

05-13-2011, 09:35 PM	#235 (permalink)
Kastley85891 A True Z Fanatic Join Date: Nov 2009 Location: ATX 370 - Sold Posts: 1,149 Drives: 2003 Wagon Rep Power: 17	A one off build, to get as far as it did first shot is impressive... looking forward to the fully finished and tweaked up version. Dam to get this far in this time is amazing really... Good work __________________ Boosted V8 hunter 2850 lbs and 375WHP

05-14-2011, 01:44 PM	#239 (permalink)
Boost_lee A True Z Fanatic Join Date: Feb 2009 Location: SATX Posts: 2,813 Drives: 09 370Z TT 6MT Rep Power: 29	i want 4.8 psi now! __________________ My TT Z

05-14-2011, 03:33 PM	#240 (permalink)
98intrigue A True Z Fanatic Join Date: Jul 2010 Location: Clearwater, FL Age: 38 Posts: 4,855 Drives: 2014 Viper Rep Power: 429	The car is having some issues with oil temps and coolant temps. Even with a 25 row Setrab oil cooler, oil temps are 240-250 with shifting at 3k rpms and not boosting at all. I'm dropping the car off tomorrow and Shawn will see it Monday. He's going to see if he can mount the oil cooler in another location. Today, my coolant was one dot away from the far right. I'm going to bleed the system and top off the coolant...hopefully, that will help. This seemed to be a common thing with 350Zs once the coolant system was opened up. __________________ Ryan - 2014 Stryker Green Viper Gone - a few Vipers and a couple turbo VQs

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS/FT: 300zx w/ Skyline GTR RB26 Single Turbo Swap 5 Speed	Z-Creations	Cars for sale (Private Classifieds)	0	01-23-2011 02:06 PM
First STS rear mount turbo 370Z???	atx370z	Nissan 370Z General Discussions	24	10-14-2010 02:53 PM
*370z needed: Single turbo kit development*	Chris@FsP	Texas	0	01-06-2010 02:05 PM
300ZX vs. Single Turbo Supras	Mercennarius	Other Vehicles	9	09-14-2009 08:59 PM
Will we see a SINGLE turbo kit?	Brazilbro	Forced Induction	17	07-03-2009 04:03 PM

05-12-2011, 11:49 PM	#227 (permalink)
Jamaica A True Z Fanatic Join Date: Mar 2010 Location: SoCal Posts: 15,362 Drives: Under boost Rep Power: 73	Looks good man.

05-14-2011, 12:01 AM	#236 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1118	Ryan, happy to help buddy. I think Making that kind of power at a low psi speaks volumes about the efficiency of the system. Get the bugs worked out and that thing will make some insane power. I have an idea bout something you can do, I'll shoot you a message tomorrow.