BP turbo build/advice

jwick · 01-21-2019, 09:50 PM

Quote:

Originally Posted by hc_416

Hey guys how do you take apart the waste-gates for cleaning? I took off all the screws on the top and bottom and it will not separate. A little advice is needed please!

I’ve never taken one apart, but dumb question, is the spring out of it?

Boosted Performance · 01-22-2019, 12:15 AM

Unless the gate is malfunctioning, there is really no reason to take it apart. Once the crews are out, there is nothing else holding the top cap in place. So be careful as the spring can send things flying once it does become loose.

James10694 · 01-22-2019, 02:34 PM

Now that were on the topic of wastegates.. I'm still having overboosting/boost creep issues. I spoke with my tuner and he sent me an updated map. Fixed the problem for a day and then started overboosting the next. I know it's not a cold weather issue because its been happening all year.

I've seen alot of other platforms having boost creep issues with the external tial wastegates. I could be going down the wrong path here but has anyone swapped to a different wastegate completely and has anyone else had this issue? I spoke to solidus about this and he said his wastegate spring pressure was not rated for what tial claimed when tested. Even if that's the case. Shouldn't the tuning keep the boost pressure from going over? I'm not the most knowledgeable when it comes to turbochargers so I'd appreciate any help or advice

I'm having a vacuum pressure test done just to rule out any type of vacuum leak.

Elmo370z · 01-22-2019, 02:36 PM

Quote:

Originally Posted by James10694

Now that were on the topic of wastegates.. I'm still having overboosting/boost creep issues. I spoke with my tuner and he sent me an updated map. Fixed the problem for a day and then started overboosting the next. I know it's not a cold weather issue because its been happening all year.

I've seen alot of other platforms having boost creep issues with the external tial wastegates. I could be going down the wrong path here but has anyone swapped to a different wastegate completely and has anyone else had this issue? I spoke to solidus about this and he said his wastegate spring pressure was not rated for what tial claimed when tested. Even if that's the case. Shouldn't the tuning keep the boost pressure from going over? I'm not the most knowledgeable when it comes to turbochargers so I'd appreciate any help or advice

I'm having a vacuum pressure test done just to rule out any type of vacuum leak.

You trying pulling apart your wastegate?

James10694 · 01-22-2019, 05:21 PM

Quote:

Originally Posted by Elmo370z

You trying pulling apart your wastegate?

I have not. Tomorrow I'm bringing it to shop for a vacuum pressure test. Might as well have them take a look while its there.

Boosted Performance · 01-22-2019, 09:46 PM

Quote:

Originally Posted by James10694

Now that were on the topic of wastegates.. I'm still having overboosting/boost creep issues. I spoke with my tuner and he sent me an updated map. Fixed the problem for a day and then started overboosting the next. I know it's not a cold weather issue because its been happening all year.

I've seen alot of other platforms having boost creep issues with the external tial wastegates. I could be going down the wrong path here but has anyone swapped to a different wastegate completely and has anyone else had this issue? I spoke to solidus about this and he said his wastegate spring pressure was not rated for what tial claimed when tested. Even if that's the case. Shouldn't the tuning keep the boost pressure from going over? I'm not the most knowledgeable when it comes to turbochargers so I'd appreciate any help or advice

I'm having a vacuum pressure test done just to rule out any type of vacuum leak.

I have not heard of any customers having issues with any boost creep.

What springs are in the gates, and what is the actual boost being seen? Also, which boost controller, and where is the boost reference for the wastegates (bottom) and boost controller pressure reference plumbed to?

If the tuner "fixed it" and it worked for a day, it sounds like a boost controller issue.

Actual boost creep due to poor exhaust/kit design would occur when you are trying to run low power/boost, not with higher boost. This is because at low power/boost, more exhaust gas needs to go through the wastegates, to bypass the turbine, and keep the boost low.

solidus · 01-22-2019, 03:01 PM

The springs test + or - 1 to 2psi. What Realstreet does is test each spring they install to match the rates. As far as taking the wastegates apart I use a C-clamp then slowly release it. Unless you want to see parts fly. Put it back together the same way to avoid crossthreading.

James10694 · 01-23-2019, 11:50 AM

I just started reading another thread and it seems that I'm not using the correct spring. I have the recommended yellow spring. Here's the link.

As for what I'm seeing. I'm tuned for 9psi and I see up to 10.3 psi on that map. Second map I'm tuned for 10psi and I have seen up to 13psi. It's not a surge or spike because it happens after running closer to redline. Map 3 Is tuned for 12psi. I haven't been able to run this map because I've seen as high as 15psi.

I'm tuned with ecutek. Boost through the ECU. My tuner said the SCG1 BC I had installed wasnt working properly so we switched over to boost through the ECU. It's still plumbed in and I use it as my boost/AFR gauge. As for where its plumbed into. I'm not entirely sure. I tapped the manifold for boost pressure.

BP kit folks. Question on wastegate plumbing.

NeverBoneStck · 01-23-2019, 01:33 PM

So people are not using the yellow spring? What spring are they using??

James10694 · 01-23-2019, 07:46 PM

Quote:

Originally Posted by NeverBoneStck

So people are not using the yellow spring? What spring are they using??

This is what I need to know as well. My tuner recommend the red spring

solidus · 01-23-2019, 04:05 PM

You use whatever spring combo that nets your desired wastegate pressure. I use my Greddy Profec in the same manner since I also have boost by ECU. Seeing as the solenoid is opened by a signal from a map sensor its reading manifold pressure which is also where your boost reference for the controller is tapped up front. That reference for me is also split with a 5psi hobbs switch and the fuel pressure regulator.

Boosted Performance · 01-23-2019, 11:59 PM

Yes, you can use any spring you want, as long as the car is tuned for it.

As for "boost creep", I am not sure that it is understood. Boost creep is an uncontrolled increase in boost as the RPM's go up. So if you are starting at say 8psi at 4k RPM, and hitting 12psi by 7k RPM, then it is considered boost creep.

I have not had any customer experience boost creep, this includes the local guys, where I installed the same kit you guys are running.

James10694 · 01-24-2019, 12:01 PM

That is exactly what I'm getting ^. Especially in 3rd and 4th gear between 5k and 7k RPMs

Boosted Performance · 01-24-2019, 12:27 PM

Quote:

Originally Posted by James10694

That is exactly what I'm getting ^. Especially in 3rd and 4th gear between 5k and 7k RPMs

There has to be an issue somewhere in the plumbing. I see the power output in your signature, is that where the issues is, or is it when you are just on spring pressure, with the EBP installed, but bypassed when only on spring?

James10694 · 01-24-2019, 02:31 PM

Quote:

Originally Posted by Boosted Performance

There has to be an issue somewhere in the plumbing. I see the power output in your signature, is that where the issues is, or is it when you are just on spring pressure, with the EBP installed, but bypassed when only on spring?

I had my shop do a vacuum leak test today and he found no leaks.Right now the EBC is plumbed in but not being utilized. It's running on spring pressure and I believe completely bypasses the EBC. I'm installing the red wastegate springs today and replacing a faulty O2 sensor. I'll be getting an updated tune as well. Hopefully that fixes my issue. I'll keep everyone posted.

01-22-2019, 12:15 AM	#2 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3384	Unless the gate is malfunctioning, there is really no reason to take it apart. Once the crews are out, there is nothing else holding the top cap in place. So be careful as the spring can send things flying once it does become loose. Spooler likes this. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

01-22-2019, 02:34 PM	#3 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 918 Drives: 2010 370z Nismo Rep Power: 14	Now that were on the topic of wastegates.. I'm still having overboosting/boost creep issues. I spoke with my tuner and he sent me an updated map. Fixed the problem for a day and then started overboosting the next. I know it's not a cold weather issue because its been happening all year. I've seen alot of other platforms having boost creep issues with the external tial wastegates. I could be going down the wrong path here but has anyone swapped to a different wastegate completely and has anyone else had this issue? I spoke to solidus about this and he said his wastegate spring pressure was not rated for what tial claimed when tested. Even if that's the case. Shouldn't the tuning keep the boost pressure from going over? I'm not the most knowledgeable when it comes to turbochargers so I'd appreciate any help or advice I'm having a vacuum pressure test done just to rule out any type of vacuum leak. __________________ Boosted Performance Single Turbo 618whp/489 tq

01-23-2019, 11:50 AM	#8 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 918 Drives: 2010 370z Nismo Rep Power: 14	I just started reading another thread and it seems that I'm not using the correct spring. I have the recommended yellow spring. Here's the link. As for what I'm seeing. I'm tuned for 9psi and I see up to 10.3 psi on that map. Second map I'm tuned for 10psi and I have seen up to 13psi. It's not a surge or spike because it happens after running closer to redline. Map 3 Is tuned for 12psi. I haven't been able to run this map because I've seen as high as 15psi. I'm tuned with ecutek. Boost through the ECU. My tuner said the SCG1 BC I had installed wasnt working properly so we switched over to boost through the ECU. It's still plumbed in and I use it as my boost/AFR gauge. As for where its plumbed into. I'm not entirely sure. I tapped the manifold for boost pressure. BP kit folks. Question on wastegate plumbing. __________________ Boosted Performance Single Turbo 618whp/489 tq

01-23-2019, 01:33 PM	#9 (permalink)
NeverBoneStck A True Z Fanatic Join Date: Oct 2009 Location: Beaverton, Or Posts: 1,110 Drives: 2008 G37 S Rep Power: 19	So people are not using the yellow spring? What spring are they using?? __________________ Juiced! That is all you need to know !!

01-23-2019, 04:05 PM	#11 (permalink)
solidus Track Member Join Date: Oct 2014 Location: Orlando, Florida Posts: 694 Drives: 15' Nismo Black 6MT Rep Power: 10082	You use whatever spring combo that nets your desired wastegate pressure. I use my Greddy Profec in the same manner since I also have boost by ECU. Seeing as the solenoid is opened by a signal from a map sensor its reading manifold pressure which is also where your boost reference for the controller is tapped up front. That reference for me is also split with a 5psi hobbs switch and the fuel pressure regulator. James10694 likes this.

01-22-2019, 03:01 PM	#7 (permalink)
solidus Track Member Join Date: Oct 2014 Location: Orlando, Florida Posts: 694 Drives: 15' Nismo Black 6MT Rep Power: 10082	The springs test + or - 1 to 2psi. What Realstreet does is test each spring they install to match the rates. As far as taking the wastegates apart I use a C-clamp then slowly release it. Unless you want to see parts fly. Put it back together the same way to avoid crossthreading.

01-23-2019, 11:59 PM	#12 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3384	Yes, you can use any spring you want, as long as the car is tuned for it. As for "boost creep", I am not sure that it is understood. Boost creep is an uncontrolled increase in boost as the RPM's go up. So if you are starting at say 8psi at 4k RPM, and hitting 12psi by 7k RPM, then it is considered boost creep. I have not had any customer experience boost creep, this includes the local guys, where I installed the same kit you guys are running. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

01-24-2019, 12:01 PM	#13 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 918 Drives: 2010 370z Nismo Rep Power: 14	That is exactly what I'm getting ^. Especially in 3rd and 4th gear between 5k and 7k RPMs __________________ Boosted Performance Single Turbo 618whp/489 tq

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Turbo Build	davidson_z34	Forced Induction	33	11-12-2015 07:45 PM
Need Advice on Bottom End Build	604GZ	Engine & Drivetrain	5	04-07-2015 09:09 AM
Single turbo build	jlask370	Forced Induction	13	10-07-2013 12:41 PM
Need advice on stereo build....	mengel	Audio & Video	7	02-08-2011 08:24 AM