Swift springs review!!!!!

bmarcinczyk14 · 04-02-2013, 10:09 AM

[QUOTE=wheee!;2246557]O degrees toe is best unless you are running a track setup... otherwise be prepared for excessive tire scrubbing. Your current settings are more than an 1/8th of an inch out from straight. Just sayin'....
That also means your tracking is off too....

If you look at my alignment sheet in my previous post, would you say my toe is too far away from zero? Also look at my camber between the front left and right, they are a bit off from each other, is this something to be concerned about?

wheee! · 04-02-2013, 10:24 AM

[QUOTE=bmarcinczyk14;2246566]

Quote:

Originally Posted by wheee!

O degrees toe is best unless you are running a track setup... otherwise be prepared for excessive tire scrubbing. Your current settings are more than an 1/8th of an inch out from straight. Just sayin'....
That also means your tracking is off too....

If you look at my alignment sheet in my previous post, would you say my toe is too far away from zero? Also look at my camber between the front left and right, they are a bit off from each other, is this something to be concerned about?

Your total toe is too much for my tastes. Your thrust angle is good, but you will be scrubbing the back tires off with that much toe. Again, some will say this is minor, but I prefer not to waste money on tires if I can help it!! Keep in mind that I have 305's on the back too and I moved my rear camber to -1.2, to get better contact with the road. That meant I needed to move the toe more to get it into line as well....

The front camber is a little off but you would need front camber arms to adjust that. I would wait till there are more choices on the market than just the SPC front camber arms....

ZMan8 · 04-02-2013, 10:27 AM

[QUOTE=bmarcinczyk14;2246566]

Quote:

Originally Posted by wheee!

O degrees toe is best unless you are running a track setup... otherwise be prepared for excessive tire scrubbing. Your current settings are more than an 1/8th of an inch out from straight. Just sayin'....
That also means your tracking is off too....

If you look at my alignment sheet in my previous post, would you say my toe is too far away from zero? Also look at my camber between the front left and right, they are a bit off from each other, is this something to be concerned about?

[QUOTE=wheee!;2246592]

Quote:

Originally Posted by bmarcinczyk14

Your total toe is too much for my tastes. Your thrust angle is good, but you will be scrubbing the back tires off with that much toe. Again, some will say this is minor, but I prefer not to waste money on tires if I can help it!! Keep in mind that I have 305's on the back too and I moved my rear camber to -1.2, to get better contact with the road. That meant I needed to move the toe more to get it into line as well....

The front camber is a little off but you would need front camber arms to adjust that. I would wait till there are more choices on the market than just the SPC front camber arms....

Cusco makes not adjustable front camber arms that they say are perfect for those who only dropped an inch (like swifts).

bmarcinczyk14 · 04-02-2013, 12:32 PM

[QUOTE=wheee!;2246592]

Quote:

Originally Posted by bmarcinczyk14

Your total toe is too much for my tastes. Your thrust angle is good, but you will be scrubbing the back tires off with that much toe. Again, some will say this is minor, but I prefer not to waste money on tires if I can help it!! Keep in mind that I have 305's on the back too and I moved my rear camber to -1.2, to get better contact with the road. That meant I needed to move the toe more to get it into line as well....

The front camber is a little off but you would need front camber arms to adjust that. I would wait till there are more choices on the market than just the SPC front camber arms....

Then why is the manufacture spec only recommend the lowest of 4 degrees? In this case it looks like he made my toe even worse than it was before, since he increased both the front and rear further from 0 than it was.

ZMan8 · 04-02-2013, 12:55 PM

[QUOTE=bmarcinczyk14;2246922]

Quote:

Originally Posted by wheee!

Then why is the manufacture spec only recommend the lowest of 4 degrees? In this case it looks like he made my toe even worse than it was before, since he increased both the front and rear further from 0 than it was.

that's normal. if they try to get your camber in spec, your toe will get out, if they try to fix the toe, then camber will get worse. <-- this only applies to OEM suspension components.

04-02-2013, 10:09 AM	#1 (permalink)
bmarcinczyk14 Track Member Join Date: Jul 2009 Location: Chicago Posts: 505 Drives: 2010 370z 6spd Sport Rep Power: 18	[QUOTE=wheee!;2246557]O degrees toe is best unless you are running a track setup... otherwise be prepared for excessive tire scrubbing. Your current settings are more than an 1/8th of an inch out from straight. Just sayin'.... That also means your tracking is off too.... If you look at my alignment sheet in my previous post, would you say my toe is too far away from zero? Also look at my camber between the front left and right, they are a bit off from each other, is this something to be concerned about? __________________ '10 370z -- '09 Ducati 848 -- '05 Kawasaki 636 Track Bike -- '02 Sentra SE-R Spec V

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Swift Springs-- Nismo Review!!	JJ-NISMO	Brakes & Suspension	39	07-29-2014 07:59 AM
[WTB] Swift Springs	Beastmode	Parts for sale (Private Classifieds)	1	09-13-2011 04:46 PM
BC ERs with Swift Springs and RA Valving REVIEW / (Picture Heavy)	Mozen	Brakes & Suspension	31	05-24-2011 10:46 AM
WTB: Swift or H&R Springs	Mr&Mrs	Wanted	5	04-26-2011 10:51 PM
Swift Springs	Justin1686	North East Region	10	02-24-2011 06:58 PM