|
My gauges came in.
|
|||||||
 |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
06-20-2017, 03:51 PM
|
#1 (permalink) |
|
Ronin Samurai - Assassin
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438   |
My gauges came in.
__________________
 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
06-21-2017, 07:48 PM
|
#2 (permalink) |
|
Ronin Samurai - Assassin
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438 |
Drilled the Z1 diff cover for the diff temp probe. The temp probe is a 1/8" NTP pipe tap. Used a "R" drill bit for the hole.
__________________
浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
|
06-21-2017, 07:51 PM
|
#3 (permalink) |
|
Ronin Samurai - Assassin
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438 |
Couple of more pic's.
__________________
浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
|
06-21-2017, 07:58 PM
|
#4 (permalink) |
|
Ronin Samurai - Assassin
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438 |
Have a question to those who have installed the SPL solid diff bushing kit with the Z1 cover. Does the bushings sit flush up against the cover or is there a small gap? Just eyeballing things up before the rest of my stuff comes. I installed the stud into the Z1 cover and sat the big SPL bushing on it. I have a gap of about 1/6".
__________________
浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
|
07-28-2017, 02:00 PM
|
#5 (permalink) |
|
Ronin Samurai - Assassin
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438 |
Sorry guys.
 I'm going to have to mothball this thread until I recover from surgery on my torn bicep muscle.  Figure about 3 months. Think it's going to end up a winter project.
__________________
浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
|
08-14-2017, 02:32 PM
|
#6 (permalink) |
|
Ronin Samurai - Assassin
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 69
Posts: 35,493
Drives: 2011 Nismo GM 6M
Rep Power: 2684438 |
Thanks Daelen, got the rest of my parts.
 OS Giken diff, Giken gear lube, carrier bearings and seals, stub axle, and AN-8 hose fitting.  Now I just have to heal up to do this work. And that will take awhile.
__________________
浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html |
|
|
|
|
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Z1 Motorsports 25 row oil cooler install | falconfixer | DIY Section (Do-It-Yourself) | 5 | 05-30-2014 04:32 PM |
| 7AT 4.08 Gear swap QUAIFE LSD Trans cooler diff cooler | matcop | Engine & Drivetrain | 17 | 09-07-2013 10:09 AM |
| Akuma Motorsports Rear Diff Cooler | Kevin@AkumaMS | Engine & Drivetrain | 24 | 05-23-2013 08:01 PM |
| Z1 Motorsports Thermostatic Sandwich Plate kit (For Nissan Motorsports Oil Cooler) | Dustin@Z1 | Drivetrain/Engine | 3 | 06-08-2012 11:10 AM |
| DIY: GT Motorsports Oil Cooler Kit Install/Review | rackley | DIY Section (Do-It-Yourself) | 28 | 03-10-2010 10:38 AM |
153Likes
Hybrid Mode
