Bought this Tanabe Medaillon exhaust :)

https://scontent-yyz1-1.xx.fbcdn.net...f6&oe=56FFDAA2

:woot:

Dropped my Z off at a shop to get Z1 clutch, flywheel, clutchline, and Zspeed HD CSC installed.

Edit... Just got a call from the shop asking permission to destroy the stock shift knob because of the 12 gallons of thread lock used to install it. WHY NISSAN. Had to destroy the one on my 2011 to replaces the knob too.

good luck!

i'm waiting until spring. if the whole shift knob being destroyed happens i guess i'll go with an aftermarket one! :rofl2:

I swear to god. Some day I will create a DIY for removing the stupid shift knob. None of this shredding and ripping of the stocker.

Wrap knob (hehe) with half a roll of e-tape. Then wrap gaffers tape around e-tape until it's the size of a softball. Take a huge pipe wrench and clamp the stupid thing onto the softball shaped tape and lefty loosie that ball until you're shredding tape. Mine popped off after 5 minutes of wrapping and had enough loctite in it to seize an elephants bunghole.

Tints!!!!!!! Sooo sexy

Nothing, just drove it to work.

http://i222.photobucket.com/albums/d...03AF510854.png

Getting coffee' up & preparing to put ~Z~ on support stands & remove factory exhaust & cats,pumpkin,wheels,rear camber arms,,, and who knows; maybe a bit more.
Waiting on some mods to come in.



Sent from my iPhone using Tapatalk

:tup:

B@t™

:tup:

B@t™

Sounds like a good day, buddy! Have fun and report back when you're finished. :tup:

Just put these new center caps on today. They weren't made for these wheels so I had to do a little surgery on them first.

Dan

Where did you get these? Exactly what I've been looking to do. :tiphat:

Forum member pfdaxe custom made a set using the Z logo from the rear 370Z emblems that looked badass: http://www.the370z.com/members-370z-...xes-build.html

http://www.the370z.com/members/pfdax...center-cap.jpg

Put in my new Berk testpipes the other weekend with the Agency Cat back

https://vimeo.com/153816808

Sent from my SM-G900V using Tapatalk

Hi, got them on Ebay. I'll try to see if they are still available.

Here's the link http://www.ebay.com/itm/181205007558...%3AMEBIDX%3AIT

Dan

u have a 350Z? :confused:

No. Si

Hi, no but that is what they were for.

Thanks Dan. I looked for them but it states that they are for 18 inches Rays and mine are 19 inches. Do you have 19 inch Rays on yours? :tiphat:

As he mentioned, they weren't made for these wheels, and he had to do a little surgery. His pic clearly shows that he has the 2013+ Sport package rims which are 19" :twocents:

Hi, yes that is why I said that I had to do surgery on them first. They are too big in diameter & have to be ground down to fit.

Dan

Went ahead and ordered a new transmission to be swapped out next weekend by corner 3 garage and going to have them install an insulated clutch line, z speed HD csc, jwt lightened flywheel and stage 1 competition clutch....so excited :)

Rolled the mileage over to 7400 miles just as I pulled into the driveway for the evening.

Love those! Makes me wish I had RAYS.

Thanks

I just got my spoiler today :excited:
Now to install it :confused:

Cool deal... I think there was a thread somewhere that had a link to a template to mount the spoiler....

Fellow Squid..good luck on install..just dont get UR neighbor Jarhead involved:}}

Yes I've seen a couple of them, it shouldn't be too bad, it's just getting up the nerve to drill holes in my trunk.

Thanks, Got that right :tup::tup:

Dan

I started putting my Swift springs on but encountered a bolt that did not want to come off and I had no penetrating fluid. :mad: impact wrench didn't even work.

had same problem putting on FI exhaust...went to HD, got a Ryobi right angle grinder $29 + cutting blade and made SHORT work of that MF.

:icon14:

Holy crap, how much torque does your impact wrench have?

I'm going to douse it in penetrating fluid and torch the bitch to see if it will break loose.

I also started refinishing my wheels and did this little project this morning in an hour. Don't know what to do with the last slot

http://i207.photobucket.com/albums/b...161853_HDR.jpg

Rear fog light switch for the last slot???

ijdmtoy rear fog light. I could get it but it wouldn't do anything

Bought a new set of Nitto tires NT01 and still waiting for its delivery hopefully by tom. So that I could install it asap.

How do you clean your USB port if it gets dirty ??

Sent from my XT907 using Tapatalk

how dirty you talking?

a keyboard blower if it's dust... maybe a q-tip with some rubbing alcohol then blow it down with the air duster.


edit: or just buy a whole new one =P