Oil change, Jack stands or ramps with diffuser?

spearfish25 · 06-27-2009, 02:09 PM

Thanks for the advice everyone.

theDreamer · 06-27-2009, 02:17 PM

I just used the Rhino ramps this morning and had no problems doing my oil change.

NeedforZ · 06-27-2009, 02:37 PM

Quote:

Originally Posted by theDreamer

I just used the Rhino ramps this morning and had no problems doing my oil change.

Same here. I use Rhino ramps and did my first oil change this morning at 1775 miles. I used a couple short 2x12s in front of the Rhinos to give the car enough lift so the chin deflector wouldn't hang. I did have to bevel the 2x12s with a jigsaw else the front tires would just push them across the floor. Worked perfectly. Gonna run Castrol GTX for a couple thousand miles before I go synthetic. Also, I would not have wanted lower ramps. I had just enough clearance to work without being too cramped.

VCuomo · 06-27-2009, 03:33 PM

Quote:

Originally Posted by NeedforZ

Same here. I use Rhino ramps and did my first oil change this morning at 1775 miles. I used a couple short 2x12s in front of the Rhinos to give the car enough lift so the chin deflector wouldn't hang. I did have to bevel the 2x12s with a jigsaw else the front tires would just push them across the floor. Worked perfectly. Gonna run Castrol GTX for a couple thousand miles before I go synthetic. Also, I would not have wanted lower ramps. I had just enough clearance to work without being too cramped.

You're using Rhino ramps and jackstands (picture shows a Craftsman jackstand)?

NeedforZ · 06-27-2009, 03:41 PM

The jackstands were just in case the plastic ramps collapsed. I slid them under there notice it's not actually supporting the car. Yeah I know the Rhinos are probably stronger than metal ramps. Call me paranoid but this is the first time I've used the plastic ones. Besides my 370z is a heavy girl at 3300lbs and I don't want her on top of me like that.

370Z Purist · 06-27-2009, 04:43 PM

Quote:

Originally Posted by NeedforZ

The jackstands were just in case the plastic ramps collapsed. I slid them under there notice it's not actually supporting the car. Yeah I know the Rhinos are probably stronger than metal ramps. Call me paranoid but this is the first time I've used the plastic ones. Besides my 370z is a heavy girl at 3300lbs and I don't want her on top of me like that.

.

I think jackstands would be more than enough. At least, if you get good ones, not the crappy ones. Then again, I've only seen them go as low as 2 tons.

wishihadnav · 08-06-2010, 12:48 PM

rhino ramps are no bueno for me...i might have to just suck it up and get the race ramps..

daleks · 08-07-2010, 12:08 PM

Quote:

Originally Posted by wishihadnav

rhino ramps are no bueno for me...i might have to just suck it up and get the race ramps..

When I measured the Nismo fascia I determined that the Race Ramps (even with the extenders) would likely rub on the lower splitter. I'd be glad to proven wrong however.

I purchased an AC Hydraulics DK13HLQ jack and will use the Race Ramps wheel cribs + jack stands in the front.

SoCal 370Z · 08-07-2010, 01:00 PM

Quote:

Originally Posted by daleks

I purchased an AC Hydraulics DK13HLQ jack and will use the Race Ramps wheel cribs + jack stands in the front.

Excellent taste in floor jacks. I have the Griot's Garage low profile floor jack (made by Melchor Gabilondo) and the two-piece 67" RaceRamps without the extenders, but our Z is a standard model not a Nismo. Plan on picking-up the floor jack you have too (just for sport).

daleks · 08-07-2010, 01:15 PM

Quote:

Originally Posted by SoCal 370Z

Excellent taste in floor jacks. I have the Griot's Garage low profile floor jack (made by Melchor Gabilondo) and the two-piece 67" RaceRamps without the extenders, but our Z is a standard model not a Nismo. Plan on picking-up the floor jack you have too (just for sport).

Thanks. I picked up the last DK13HLQ from acjacks.com. I'll post a review in the DIY section (AK should add a Tools section for reviews...) when it arrives next week. The seller lives across the state from me so the shipping wasn't too bad, but I'm sure most people would balk at the total price.

I'll still have to use starter ramps (~2 inches), but this model lifts above 20". If I want to get my wheels on 12" wheel cribs I'll have to compensate for the suspension droop in addition to the 12" crib height. Anyway I'll post pics at a later date.

SoCal 370Z · 08-07-2010, 01:19 PM

Quote:

Originally Posted by daleks

Thanks. I picked up the last DK13HLQ from acjacks.com. I'll post a review in the DIY section (AK should add a Tools section for reviews...) when it arrives next week. The seller lives across the state from me so the shipping wasn't too bad, but I'm sure most people would balk at the total price.

Believe me, you've purchased the best floor jack available for the enthusiast and professional in the world today! You will not be disappointed. Pickup some spare wheels and o-rings if they are in stock. Most AC Hydraulic diehards stockpile replacement parts for these pups as they are lifetime keepers.

rmorrow · 08-06-2010, 07:03 PM

I bought race ramps. I still shove jack stands under both sides and chock the wheels as an extra safety precaution. The race ramps are real expensive...but they sure work great and store easily.

zilent_jay · 08-07-2010, 04:55 AM

Boost_lee · 08-07-2010, 05:11 AM

^^ very nice

shadow2k · 08-07-2010, 11:54 AM

I use Rhino 12,000 ramps with a 2x4 in front. I take off the diffusers from in front of each wheel. They rub slightly, which I doubt would be an issue, but I don't want to tear them off or anything. They're just three little plastic screws holding each on, and with them off, nothing rubs.

I have a pair of jack stands and a normal floor jack for when I need to take off the wheels. No need for low profile, as I can just run it up the ramps first.

06-27-2009, 02:17 PM	#2 (permalink)
theDreamer A True Z Fanatic Join Date: Feb 2009 Location: Texas Posts: 30,879 Drives: 370z Rep Power: 4211	I just used the Rhino ramps this morning and had no problems doing my oil change. __________________ theDreamer's Z // Fast Intentions // Uprev // GTM // HKS // TEIN theDreamer's Silvia // URAS // GREDDY Houston Zs // Facebook // Twitter // Instagram

06-27-2009, 03:41 PM	#5 (permalink)
NeedforZ Base Member Join Date: Mar 2009 Location: DFW Texas Posts: 163 Drives: 370z Touring 7AT Rep Power: 17	The jackstands were just in case the plastic ramps collapsed. I slid them under there notice it's not actually supporting the car. Yeah I know the Rhinos are probably stronger than metal ramps. Call me paranoid but this is the first time I've used the plastic ones. Besides my 370z is a heavy girl at 3300lbs and I don't want her on top of me like that. Last edited by NeedforZ; 06-27-2009 at 03:43 PM. Reason: clarity

08-07-2010, 04:55 AM	#13 (permalink)
zilent_jay Base Member Join Date: May 2009 Location: OKC Posts: 96 Drives: 2009 MB Base Sport Rep Power: 17	I vote for tornado shelter.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Oil Change	armensti	Engine & Drivetrain	155	04-18-2012 01:39 PM
Jack Stands	Minicobra1	DIY Section (Do-It-Yourself)	19	03-07-2010 04:54 PM
1st Oil Change	tooohip	Mid-Atlantic Region	4	06-25-2009 07:50 PM
(Noob question) SRM stands for?	leepeen	Nissan 370Z General Discussions	1	05-25-2009 08:33 PM
First Oil Change	cotizi	Engine & Drivetrain	3	03-27-2009 11:34 AM

06-27-2009, 02:09 PM	#1 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1857	Thanks for the advice everyone.

08-06-2010, 12:48 PM	#7 (permalink)
wishihadnav A True Z Fanatic Join Date: Nov 2009 Location: 90090 Posts: 1,851 Drives: Force Fed Nismo Rep Power: 184	rhino ramps are no bueno for me...i might have to just suck it up and get the race ramps..

08-06-2010, 07:03 PM	#12 (permalink)
rmorrow Base Member Join Date: Jun 2010 Location: Houston Posts: 79 Drives: 2010 370z Sports MT Rep Power: 16	I bought race ramps. I still shove jack stands under both sides and chock the wheels as an extra safety precaution. The race ramps are real expensive...but they sure work great and store easily.

08-07-2010, 05:11 AM	#14 (permalink)
Boost_lee A True Z Fanatic Join Date: Feb 2009 Location: SATX Posts: 2,813 Drives: 09 370Z TT 6MT Rep Power: 30	^^ very nice

08-07-2010, 11:54 AM	#15 (permalink)
shadow2k Base Member Join Date: Jul 2009 Location: Overland Park, Kansas Posts: 143 Drives: 09 PG 370z 6MT Rep Power: 16	I use Rhino 12,000 ramps with a 2x4 in front. I take off the diffusers from in front of each wheel. They rub slightly, which I doubt would be an issue, but I don't want to tear them off or anything. They're just three little plastic screws holding each on, and with them off, nothing rubs. I have a pair of jack stands and a normal floor jack for when I need to take off the wheels. No need for low profile, as I can just run it up the ramps first.