V1H

Hey - also just asking about your DIY: Aftermarket Seats Installation post. Regarding the passenger occupancy sensor, I'm interested in going with your switch method and my understanding is the sensor has the IGN, GND & COM, and I should be wiring the IGN and GND, to switch's 12V and GND wires respectively, but for COM, I connect it to a 2-wire lead (one with 15 Ω, and other blank) to the switch's power/device wire - is this correct?


Thanks in advance.

Hey, I was trying to bypass my seat sensor based on your braum install thread. The photos seem to be lost, so I only had your text to go on. Did you have a seat connector with 3 wires to it? (12v, com, gnd) I tried placing a 15ohm resistor between com and gnd but it seemed to give me the flashing airbag light. Do you remember which pins you put the resistor in?

Thanks

You won't find a bracket; you have to home-make one. That is, just use two aluminium right angle pieces from hardware store, bend it to shape by hand, then slap on some fibre mesh and resin (from a DIY car body repair kit from any car store)

Hey thanks for the message! My Z does have the stock DRLs. What kind of bracket did you use? My problem is that since they do not fit, I dont know of a bracket that I could use to connect lights behind the bumper. If I could find a bracket or something, then I would be ale to use my stock DRLs behind the bumper

Hey! Sorry to bother but I was wondering if you could give me some info regarding your amuse drl? I am going to install the bumper soon and I would very much like to keep my Drls or a variant of it!

Thanks in advance 😊

Install your new Powerhouse Amuse Vestito front & rear bumpers yourself and save some money Got my Amuse bumpers thru Bulletproofautomotive. Manufactured in Japan, shipped to U.K. via California....

When Craig bolted on the downpipes, they touched the underfloor. They will have to be cut and re-welded to slightly correct their angle, not ideal being ceramic coated but the only way. AAM used a...

When Craig bolted on the downpipes, they touched the underfloor. They will have to be cut and re-welded to slightly correct their angle, not ideal being ceramic coated but the only way. AAM used a...

When Craig bolted on the downpipes, they touched the underfloor. They will have to be cut and re-welded to slightly correct their angle, not ideal being ceramic coated but the only way. AAM used a...

Craig put back all bits onto the engine, looking nearly final now. Unfortunately, there's so little space now everywhere that he wasn't able to fit my expensive Radium Engineering dual OCCs :cry:...

Craig put back all bits onto the engine, looking nearly final now. Unfortunately, there's so little space now everywhere that he wasn't able to fit my expensive Radium Engineering dual OCCs :cry:...

Craig put back all bits onto the engine, looking nearly final now. Unfortunately, there's so little space now everywhere that he wasn't able to fit my expensive Radium Engineering dual OCCs :cry:...

Craig put back all bits onto the engine, looking nearly final now. Unfortunately, there's so little space now everywhere that he wasn't able to fit my expensive Radium Engineering dual OCCs :cry:...

Update on the TT install: My external oil cooler setup needed to be modified, the hoses caused interference, new fittings have now been made. The standard cooler lines for the OEM oil filter had to...

Hi there, The engine setup needed some tweaking for it to seat nicely in engine bay without any chafing problems. It's fitted now, together with the FMIC and piping ...

Hi there, The engine setup needed some tweaking for it to seat nicely in engine bay without any chafing problems. It's fitted now, together with the FMIC and piping ...

Car ramps arrived this morning. And I just finished installing my Motodyne Shockwave))) Holy m*****f****** ****! The sound is simply otherworldly :eek: My Z now sounds like it's on steroids. I...

Hi there, The engine setup needed some tweaking for it to seat nicely in engine bay without any chafing problems. It's fitted now, together with the FMIC and piping ...

No mate, mine looks like this: http://www.prelude.myzen.co.uk/370Z/Temp/FullSizeRender.jpg

Today's a special day. 2.5 yrs ago I bought the AAM TT RHD kit. Developent took this long. Today I took my 370Z to Horsham Developments (U.K.) for the install (together with various supporting...