JLarson's build thread

redondoaveb · 03-04-2020, 05:04 PM

Quote:

Originally Posted by JLarson

Car is alive!!! It was the tune!!

It's such a good feeling

Memphis370Z · 03-04-2020, 05:14 PM

Quote:

Originally Posted by JLarson

Car is alive!!! It was the tune!!

Hotrodz · 03-04-2020, 05:36 PM

Quote:

Originally Posted by JLarson

Car is alive!!! It was the tune!!

Yahoo! Boost problems suck...

Sent from my SM-G965U using Tapatalk

OldGrayDog · 03-04-2020, 05:52 PM

Quote:

Originally Posted by JLarson

Car is alive!!! It was the tune!!

awesome!

JLarson · 03-09-2020, 06:28 AM

Hopefully final updates on this part of the process. Saturday, I went through the build, tidying up. Interior is back together. Added wiring has been secured with zip ties behind the dash. Replaced the cabin air filter while I was fiddling around with everything else, since I've had a replacement for an embarassingly long time without installing it. Interior looks stock, except for the gauge pod additions.

Ran the car for a while to check for leaks. Idle is very stable @ ~900 rpms, AFR at idle is about 14:1. After running for 30 minutes, I was still getting single drips of oil at the oil cooler, so I drained the oil, disconnected the fittings from the plate, went back over everything with thread sealant and tightened it all up. Problem solved.

Same thing under the turbo. I could still see a single drop of coolant emerging every few minutes from one of the coolant lines - unfortunately, it was the one I couldn't reach with any of my wrenches. I'd had enough fun for one day, so I went out to Longhorn Steakhouse with the wife instead.

Sunday I dropped the turbo, re-tightened the fittings (one had loosened slightly during install, that was my issue) and took the time to add a few zip ties and heat shielding to nearby wiring. I used my transmission jack to hold the turbo instead of lifting it over my head the entire time. Reinstalled everything, added the turbo blanket.

Last obstacle was the Quickjack. Per the manufacturers instruction, I refilled the transmission fluid in the reservoir although wisely not all the way (more on this momentarily). Since the quick connect fittings were the issue, specifically the short lines mounted to the rails, I disconnected those fittings and allowed them to drain. More thread sealant, tightened the fittings back up, connected the Quickjack, and lowered the car! ... creating as I did so a literal fountain of transmission fluid from the Quickjack reservoir breather valve which sprayed both my front bumper and the ceiling of my garage. After some light panicked cleaning, order was restored.

In hindsight, the fountain was very pretty, but I cannot recommend. Do not refill reservoir. Despite the manufacturers rec, you will not lose enough fluid from the lines to merit a full refilling.

The red dragon is on the ground.

old guy · 03-09-2020, 07:42 AM

Awsome.

Hotrodz · 03-09-2020, 08:51 AM

Congrats!

Sent from my SM-G965U using Tapatalk

Rusty · 03-09-2020, 09:39 AM

It's alive.......it's alive!!!!

JLarson · 03-10-2020, 06:22 AM

Went for a very low speed cruise last night, just a couple blocks. I pretty quickly noticed some resistance when turning the wheel. Got the car back up on the Quickjack, and discovered one of my very clever clamp locations for the piping was interfering. It was a simple fix, but time consuming. I'll try another shakedown tonight.

gbrettin · 03-11-2020, 08:32 AM

You are on the downhill slide! I'm quite envious. Congratulations!

JLarson · 03-11-2020, 08:37 AM

Tune is set for the 24th - I'm so excited my nipples could cut glass!

solidus · 03-11-2020, 10:12 AM

Quote:

Originally Posted by JLarson

Went for a very low speed cruise last night, just a couple blocks. I pretty quickly noticed some resistance when turning the wheel. Got the car back up on the Quickjack, and discovered one of my very clever clamp locations for the piping was interfering. It was a simple fix, but time consuming. I'll try another shakedown tonight.

The infamous steering knuckle charge pipe. I hate that one. I've asked Sasha for a set of pipes from the turbo to the one just before the intercooler charge pipe. I'm gonna pull them all and put the new set in because I believe that one is bent and damaged.

JLarson · 03-11-2020, 12:38 PM

Quote:

Originally Posted by solidus

The infamous steering knuckle charge pipe. I hate that one. I've asked Sasha for a set of pipes from the turbo to the one just before the intercooler charge pipe. I'm gonna pull them all and put the new set in because I believe that one is bent and damaged.

In my case, the pipe does clear, it was the clamp that didn't. I found what I thought was a great place for the clamp. Unfortunately, the t-bolt was just a little too close. But yeah, its a very tight spot. Easily my least favorite part of this project - other than my original non-functioning tune and my intercooler with the backwards bracket.

solidus · 03-11-2020, 02:03 PM

Quote:

Originally Posted by JLarson

In my case, the pipe does clear, it was the clamp that didn't. I found what I thought was a great place for the clamp. Unfortunately, the t-bolt was just a little too close. But yeah, its a very tight spot. Easily my least favorite part of this project - other than my original non-functioning tune and my intercooler with the backwards bracket.

Yeah mone was the clamp too but the tight space is irritating af.

JLarson · 03-11-2020, 04:48 PM

Quote:

Originally Posted by solidus

Yeah mone was the clamp too but the tight space is irritating af.

That part was just very frustrating. Windex is not optional there. Without it, you're just asking for pain.

03-09-2020, 07:42 AM	#306 (permalink)
old guy A True Z Fanatic Join Date: Apr 2015 Location: S.E. Michigan Age: 67 Posts: 2,706 Drives: 13 magma touring Rep Power: 2684369	Awsome. gbrettin, JARblue, Rusty and 4 others like this. __________________ I better walk before they make me run....

03-09-2020, 08:51 AM	#307 (permalink)
Hotrodz Premium Member Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684384	Congrats! Sent from my SM-G965U using Tapatalk gbrettin, Rusty, old guy and 2 others like this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

03-09-2020, 09:39 AM	#308 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 34,870 Drives: 2011 Nismo GM 6M Rep Power: 2684436	It's alive.......it's alive!!!! gbrettin, Hotrodz, Ghostvette and 3 others like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

03-10-2020, 06:22 AM	#309 (permalink)
JLarson A True Z Fanatic Join Date: Jun 2017 Location: Media, PA Posts: 4,074 Drives: 14 Nissan 370z MR M6 Rep Power: 2684369	Went for a very low speed cruise last night, just a couple blocks. I pretty quickly noticed some resistance when turning the wheel. Got the car back up on the Quickjack, and discovered one of my very clever clamp locations for the piping was interfering. It was a simple fix, but time consuming. I'll try another shakedown tonight. gbrettin, JARblue, Rusty and 9 others like this. __________________ 2014 370z Touring Sport Magma Red MT // BP Single Turbo 6467 // 63mm TB's // Z1 Ported Upper Mani // RJM Pedal // Zspeed Stage 3 Clutch // 526 WHP, 451 WTQ 2006 350z (Sold) // 1990 300zx (Sold) // 1985 300zx 2+2 (Sold)

03-11-2020, 08:32 AM	#310 (permalink)
gbrettin A True Z Fanatic Join Date: Oct 2010 Location: Portage, MI Posts: 2,238 Drives: Tricycle Rep Power: 542172	You are on the downhill slide! I'm quite envious. Congratulations! Hotrodz, Ghostvette, sx moneypit and 3 others like this.

03-11-2020, 08:37 AM	#311 (permalink)
JLarson A True Z Fanatic Join Date: Jun 2017 Location: Media, PA Posts: 4,074 Drives: 14 Nissan 370z MR M6 Rep Power: 2684369	Tune is set for the 24th - I'm so excited my nipples could cut glass! gbrettin, JARblue, Rusty and 7 others like this. __________________ 2014 370z Touring Sport Magma Red MT // BP Single Turbo 6467 // 63mm TB's // Z1 Ported Upper Mani // RJM Pedal // Zspeed Stage 3 Clutch // 526 WHP, 451 WTQ 2006 350z (Sold) // 1990 300zx (Sold) // 1985 300zx 2+2 (Sold)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
JLarson's Great Big Dyno Results Thread!	JLarson	Engine & Drivetrain	17	01-05-2018 03:22 PM
My Build Thread	370z1129	Nissan 370Z General Discussions	6	11-06-2014 04:54 PM
ENT-Z Build Thread	ENT-Z	Member's 370Z Gallery	68	09-06-2014 10:00 PM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 05:24 PM