![]() |
Originally Posted by Nissan370 ok so mike(anmvq) sent me his cog pulley set-up for my stillen kit besides spacers is there anything else i need to do to get this
|
![]() |
|
LinkBack | Thread Tools | Display Modes |
|
![]() |
#1 (permalink) | |
A True Z Fanatic
![]() Join Date: Dec 2011
Location: Pensacola Florida
Posts: 1,696
Drives: Awesome Car
Rep Power: 27 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]() Quote:
What kit do you have? Why do you think you need bigger piping and UPREV MAFs. Will PM you on this one. I got on of these at auto zone for 32.00 to pull the Stillen pulleys off. Just take your time and if they wont budge heat the face of the pulley up with a propane torch from home depot. Do not heat the shaft, you don;t want to damage the bearings, just want to unseeze the pulleys from the key. ![]() ![]() Once you get them off you will reuse the Keys (Small Square Rod) with the Vortex Pulleys you have. Go to a hardware store and bring your the bolt that held the pulley on and get a longer one. 2.5 or 3 inch. You can use it to press the COGs on and use it as your new COG Drive pulley bolt. Next: If you don't want to through belts you have to brace the 1/4 aluminum plate the SC is mounted to. It flexes under gas. We want to stop the flexing. These pics are from Osiris: ![]() The gold hex rod is attached to the plate and to the firewall and is adjustable to enable you to get the belt to ride in the center of the pulleys. ![]() This is what I will use as my adjustable rod, you can get it off any chopper site that sells springer brake parts. ![]() I'll fab up a mounting plate and fire wall tabs to bolt it on.. Hope this helps, please let me know if you need more.. Ck out the photo album. Rep if you like.. ![]()
__________________
Did new cool science stuff to the car !!!
http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html Last edited by Nut_N_Much; 11-12-2012 at 03:56 PM. |
|
![]() |
![]() |
![]() |
#2 (permalink) |
A True Z Fanatic
![]() Join Date: Dec 2011
Location: Pensacola Florida
Posts: 1,696
Drives: Awesome Car
Rep Power: 27 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Should look like this when your done mounting them:
![]() ![]() ![]() Then painted to color match the car.. ![]() Good DIY KellyFields pointed me to is this: wortmeister re-wrote the Stillen Direction to help ID problem areas not written about by Stillen.. 370Z Stillen supercharger DIY instructions ![]()
__________________
Did new cool science stuff to the car !!!
http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html |
![]() |
![]() |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Stillen pulley review | indyn | Engine & Drivetrain | 21 | 10-05-2015 01:00 AM |
[FOR SALE] stillen crank pulley | Huan'z | Parts for sale (Private Classifieds) | 20 | 04-14-2012 10:01 PM |
stillen underdrive pulley ? | redroadster10 | Engine & Drivetrain | 5 | 04-08-2010 01:54 AM |
FI 12" Exhaust - Stillen G3 Intakes - Stillen UD Pulley - GAINED 28kw or 37HP | bezzita | Australia/New Zealand | 29 | 09-27-2009 12:53 PM |
FI 12" Exhaust - Stillen G3 Intakes - Stillen UD Pulley - GAINED 28kw or 37HP | bezzita | Engine & Drivetrain | 6 | 09-06-2009 05:20 PM |