cog pulley and stillen kit plz advice

[Nissan370]

ok so mike(anmvq) sent me his cog pulley set-up for my stillen kit
besides spacers is there anything else i need to do to get this on the car and working
and if anyone has pictures that would be cool to thxs

also if i get the uprev maf's will i be fine or do i still need to some how upgrade to larger intake piping

[elperuano]

Smh... Make sure u got all ur piggy banks filled with quarters.

[Nissan370]

lol why you say that ? i have a built motor and i am using water/meth and my tuner is tuning for reliabilty i mean worst thing would be some kinda belt slippage

[elperuano]

You have a built motor and water/meth and ur using a stillen kit????

[Mr&Mrs]

Why post if your not going to help? Man people annoy me!

Anyway I do not know much about this but two people I know for sure that are very very nice, and will help out are: MrSqueeze and Nut_N_Much

Nut_N_Much is currently doing this on his own and has posted a few pics in his build journal so check it out Click Here. MrSqueeze was the first I know of to use this setup and has moved on to bigger better things. He is also a wealth of knowledge for this setup.

[Nissan370]

thxs mr&mrs lol

(still with stillen)ya i know but i am still trying to recover from dropping 9k on the kit installed and 8.5k on a new motor
maybe late spring early summer i can do turbo just working with what i got
stillen kit is not a great kit but the vortech is a good blower

[ANMVQ]

Hey man I have some pics on my phone from Mr.Sqeeze he helped me a lot, he still is helping, lol great guy.Just text me and ill shot you the pics. BTW nothing special to get them yo work just up grade the MAF'S and you should be good. I would look into a upgrade for the small heat exchanger too. if my car goes south Ill sell you Mine. I have been think about parting it out just incase.

[Nut_N_Much]

Originally Posted by Nissan370

ok so mike(anmvq) sent me his cog pulley set-up for my stillen kit
besides spacers is there anything else i need to do to get this on the car and working
and if anyone has pictures that would be cool to thxs

also if i get the uprev maf's will i be fine or do i still need to some how upgrade to larger intake piping

Hey brother,
What kit do you have? Why do you think you need bigger piping and UPREV MAFs. Will PM you on this one.

I got on of these at auto zone for 32.00 to pull the Stillen pulleys off. Just take your time and if they wont budge heat the face of the pulley up with a propane torch from home depot. Do not heat the shaft, you don;t want to damage the bearings, just want to unseeze the pulleys from the key.



Once you get them off you will reuse the Keys (Small Square Rod) with the Vortex Pulleys you have. Go to a hardware store and bring your the bolt that held the pulley on and get a longer one. 2.5 or 3 inch. You can use it to press the COGs on and use it as your new COG Drive pulley bolt.

Next: If you don't want to through belts you have to brace the 1/4 aluminum plate the SC is mounted to. It flexes under gas. We want to stop the flexing. These pics are from Osiris:

The gold hex rod is attached to the plate and to the firewall and is adjustable to enable you to get the belt to ride in the center of the pulleys.


This is what I will use as my adjustable rod, you can get it off any chopper site that sells springer brake parts.


I'll fab up a mounting plate and fire wall tabs to bolt it on..

Hope this helps, please let me know if you need more.. Ck out the photo album. Rep if you like..

[elperuano]

Originally Posted by Mr&Mrs

Why post if your not going to help? Man people annoy me!

Anyway I do not know much about this but two people I know for sure that are very very nice, and will help out are: MrSqueeze and Nut_N_Much

Nut_N_Much is currently doing this on his own and has posted a few pics in his build journal so check it out Click Here. MrSqueeze was the first I know of to use this setup and has moved on to bigger better things. He is also a wealth of knowledge for this setup.

What's annoying is to see a custom built motor and water/meth on an outdated kit. Put that thing to good use. If you guys wanna help him with that beast go get some groceries go ahead.. It's annoying to see such potential go to waste.. Carry on guys, don't forget to hold hands while u cross the street!

[Mr&Mrs]

He explained why, but you still continue to bash. High five buddy!

[Nut_N_Much]

Should look like this when your done mounting them:





Then painted to color match the car..

Good DIY KellyFields pointed me to is this: wortmeister re-wrote the Stillen Direction to help ID problem areas not written about by Stillen.. 370Z Stillen supercharger DIY instructions

[Mr&Mrs]

Very nice! That is going to look so sick!

[Nut_N_Much]

Originally Posted by elperuano

What's annoying is to see a custom built motor and water/meth on an outdated kit. Put that thing to good use. If you guys wanna help him with that beast go get some groceries go ahead.. It's annoying to see such potential go to waste.. Carry on guys, don't forget to hold hands while u cross the street!

Thats funny, you sure do ask a lot of questions in your public profile, last time I check, didn't see anyone give you a hard time in there. Do you do your own work or do you pay for someone to do it for you aka GreenGoblen and you put this guy down for working through it him self. Good job hope you feel good about your self, carry one !!!

[SharpByCoop]

Nice project. Glad to see these viable kits being used. 450+hp feels great no matter what the source is.

Haters gonna hate...! LOL!

Coop

[elperuano]

Didn't know he built his motor, good job on that OP. I paid my buddy Greengoblin to install my turbo kit. I also clearly stated that so don't know what you're getting there, but keep trying cuz ur failing. Simply said its sad to see the potential of this motor being toned down. If u guys wanna help this monster get groceries go ahead, it's still sad.
Anymore public info u find out and care to re-repeat after I post it go right ahead Captain Obvious.