Topgunz - air to air upgrade

nic370 · 02-10-2017, 03:20 PM

Quote:

Originally Posted by TopgunZ

Did he take the intercooler out of the manifold? If that is in there it will plug it up and make more backpressure/boost.

Yeah we took that out
And I'm running invidia Gemini with de cats

He asked me if I'd changed the pulleys

Sent from my SM-G920F using Tapatalk

mikey1600 · 02-10-2017, 10:09 PM

Hey mate, good to see a fellow Aussie doing it!

were you already custom tuned before installing the A2A? if so that's a pretty damn good increase to be honest.

I'm looking to do the same except adding E85 + Si trim upgrade on the charger

Quote:

Originally Posted by Optimiser

Well finally after months of waiting for and stuffing around with parts from the US and lots of $$$ my shop has finally completed my A to A upgrade!

Some things to note were that the Stillen fuel pump ran out of pressure when engine was at 5500RPM and was replaced with a 340LPH pump. I've ended up using a 3.00" improved traction SC pulley, stock jack shaft pulley and a 2.80"improved traction serp pulley, giving me 10PSI. I replaced both the SC and serp belts and used the extra idler pulley (with special spacer), that was supplied to me by the most helpful and friendly "TBatt". This is to try and stop any belt slippage on serp side. I am also using the Tial BPV.
The Stillen fuel injectors did not need replacing and I'm using BP "Ultimate" 98 RON fuel which is the best you can get here in Australia. The injectors didn't max out and are fine with my current tune. I'm also Uprev tuned and using the stock MAF's, so no SD tuning on this. The dyno is a "Dynapack chassis dyno which are popular in Japan. They are the "static" ones where your (driven) wheels are removed and connected to a unit that spins a hydraulic pump/motor. The wobbles on the dyno graph's lines are due to the Dynapack's sensor which fluctuates a bit in hotter weather (it's middle of summer here down under) and is therefore not at all to do with fluctuations with the engine, so ignore them. The tune is very stable and smooth and the engine idles perfectly.
Overall I was hoping to get a bit more power than this, but around 450 (safe) WHP and about 352 wheel torque, it's still great and I'm happy. I'm also glad it's all over and I have my car back finally! You can see the before (Standard Stillen setup) and after (TopGunz A to A upgrade) results on the dyno charts.

shadow85 · 02-11-2017, 01:59 AM

Quote:

Originally Posted by mikey1600

Hey mate, good to see a fellow Aussie doing it!

were you already custom tuned before installing the A2A? if so that's a pretty damn good increase to be honest.

I'm looking to do the same except adding E85 + Si trim upgrade on the charger

How much extra power would the Si trim upgrade net you?

ChaseZ · 02-11-2017, 04:12 AM

Quote:

Originally Posted by shadow85

How much extra power would the Si trim upgrade net you?

Si adds about 2-3psi, in theory should be extra 40-60whp. That's not contemplating the e85 don't know what that would add by itself.

MoulaZ · 02-11-2017, 04:51 AM

Quote:

Originally Posted by ChaseZ

Si adds about 2-3psi, in theory should be extra 40-60whp. That's not contemplating the e85 don't know what that would add by itself.

Well since we now have a reasonable idea of 10 psi + A2A kit nets about 320rwkw, and there is a guy on the original 6 psi kit with e85 making a hair past 300rwkw... I'm going to stab for fun and say 12 psi + e85 + A2A + good tune will hit ~360rwkw (~480rwhp).

In a couple of weeks, I'll have my own results of 10 psi + A2A as well.

shadow85 · 02-11-2017, 07:02 AM

Quote:

Originally Posted by MoulaZ

Well since we now have a reasonable idea of 10 psi + A2A kit nets about 320rwkw, and there is a guy on the original 6 psi kit with e85 making a hair past 300rwkw... I'm going to stab for fun and say 12 psi + e85 + A2A + good tune will hit ~360rwkw (~480rwhp).

In a couple of weeks, I'll have my own results of 10 psi + A2A as well.

Do you think I will be able to hit 360 rwkw with the AAM TT Kit on 10psi? No e85

TopgunZ · 02-11-2017, 08:09 AM

Stillenz84 made 556whp with the above.
Frandy made 540whp with stillen fuel components, pump gas plus meth.
Sudip made 515whp. I just posted his dyno a few pages back. It's not hard to get past 500.

TopgunZ · 02-11-2017, 08:39 AM

Quote:

Originally Posted by ChaseZ

Si adds about 2-3psi, in theory should be extra 40-60whp. That's not contemplating the e85 don't know what that would add by itself.

It won't get you 50whp. It flows 1150cfm vs 1050 so around 10% more. It will be closer to 2 psi which will be around 30-35whp.

jwick · 02-11-2017, 09:25 AM

Quote:

Originally Posted by shadow85

Do you think I will be able to hit 360 rwkw with the AAM TT Kit on 10psi? No e85

Wrong thread. This thread is about Guns A2A kit.

ChaseZ · 02-11-2017, 09:43 AM

Quote:

Originally Posted by TopgunZ

It won't get you 50whp. It flows 1150cfm vs 1050 so around 10% more. It will be closer to 2 psi which will be around 30-35whp.

Makes sense. I was just using the typical average of 20 per psi
Obviously you have more specific information in this case. Good to know, helps me get an idea of what to expect on mine too

MoulaZ · 02-11-2017, 04:26 PM

Quote:

Originally Posted by TopgunZ

Stillenz84 made 556whp with the above.
Frandy made 540whp with stillen fuel components, pump gas plus meth.
Sudip made 515whp. I just posted his dyno a few pages back. It's not hard to get past 500.

I don't disagree mate, I'm only accounting for the bizarre fact US Dynos & Aussie Dynos have never in their history ever read the same. When I got it back after the first Tune it netted just 265rwkw, which is 355whp. Got a video of a pull I did on a hot night. Before you comment, watch it.

I'm curious, in 'your' eyes, what does this look/seem like?

https://youtu.be/rL1vkYbfEdw

Kzonts · 02-11-2017, 05:25 PM

Stopping at 6K in 4th gear is not a complete run. Right?

MoulaZ · 02-11-2017, 05:41 PM

Quote:

Originally Posted by Kzonts

Stopping at 6K in 4th gear is not a complete run. Right?

Yeah I backed off.

Kzonts · 02-11-2017, 07:18 PM

Quote:

Originally Posted by MoulaZ

Yeah I backed off.

Ignore my stupidity. I though the vid was done on the dyno...

Optimiser · 02-11-2017, 09:03 PM

[QUOTE=MoulaZ;3614575]I don't disagree mate, I'm only accounting for the bizarre fact US Dynos & Aussie Dynos have never in their history ever read the same. When I got it back after the first Tune it netted just 265rwkw, which is 355whp. Got a video of a pull I did on a hot night. Before you comment, watch it.

I'm curious about this too. If the Dyno readings were similar is the US to AUS, shouldn't I be closer to 500WHP with my A to A setup? If not what is holding me back from being closer to 500WHP as I thought my setup now is very similar to some of the US ones that are making around 500WHP? Mine showing about 450WHP on a "Dynapack" dyno.

02-11-2017, 08:09 AM	#1492 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6833	Stillenz84 made 556whp with the above. Frandy made 540whp with stillen fuel components, pump gas plus meth. Sudip made 515whp. I just posted his dyno a few pages back. It's not hard to get past 500. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM Last edited by TopgunZ; 02-11-2017 at 08:18 AM.

02-11-2017, 05:25 PM	#1497 (permalink)
Kzonts Track Member Join Date: Mar 2015 Location: Greenville, SC Age: 60 Posts: 712 Drives: 2019 Roadster Rep Power: 104555	Stopping at 6K in 4th gear is not a complete run. Right? __________________ 2019 Magnetic Black Roadster FI Exhaust \| EVO-R Rear Diffuser \| Artwork Bodyshop Front Splitter \| Tuned By Specialty Z

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Best upgrade/mod for 200-300$?	louiey370z	Engine & Drivetrain	10	06-09-2015 11:59 PM
Upgrade?	Dzel	Other Vehicles	83	03-08-2014 05:55 PM
Upgrade	Darryl79	New Roadster 370Z Owner	7	08-23-2012 02:21 PM
Big 3 upgrade ???	dbkustomz	Audio & Video	6	06-30-2012 07:00 AM

02-11-2017, 09:03 PM	#1500 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 453 Drives: 2012 Nissan 370Z MT Rep Power: 20144	[QUOTE=MoulaZ;3614575]I don't disagree mate, I'm only accounting for the bizarre fact US Dynos & Aussie Dynos have never in their history ever read the same. When I got it back after the first Tune it netted just 265rwkw, which is 355whp. Got a video of a pull I did on a hot night. Before you comment, watch it. I'm curious about this too. If the Dyno readings were similar is the US to AUS, shouldn't I be closer to 500WHP with my A to A setup? If not what is holding me back from being closer to 500WHP as I thought my setup now is very similar to some of the US ones that are making around 500WHP? Mine showing about 450WHP on a "Dynapack" dyno.