Nissan 370Z Forum - Topgunz - air to air upgrade

Hard to explain, and will try and get a clip but the best I could describe is like when an idler pulley is on it's way out.

I did notice a little bit of green on the very 1-2mm edge of the idler pulley you supply when installed. Easily rubbed off with a finger though.

Give it a few miles (kilometers in your case) to get broken in.

Check the idler and see if it is running hot. That could indicate that the bearing is bad.

redondoaveb

01-20-2018 12:16 PM

My car made Specialty Z's Instagram page. :happydance:
https://www.instagram.com/p/BeKIpuljVDU/

Senna-F1

01-20-2018 12:42 PM

Quote:

Originally Posted by redondoaveb (Post 3723418)

My car made Specialty Z's Instagram page. :happydance:
https://www.instagram.com/p/BeKIpuljVDU/

Fantastic! Do you know why he eased off the throttle at 7000 RPM?

redondoaveb

01-20-2018 01:37 PM

Quote:

Originally Posted by Senna-F1 (Post 3723425)

Fantastic! Do you know why he eased off the throttle at 7000 RPM?

Thanks. I haven't asked him about that.

overtureZ

01-20-2018 03:12 PM

Hey Aaron, the Tial you provide comes with the correct spring right?

TopgunZ

01-20-2018 03:36 PM

The correct spring is 1.5psi. It would have came with that.

brucelidat

01-20-2018 05:44 PM

Is this about what we should be expecting from the kit? Do you ave a dyno you can post?

Quote:

Originally Posted by redondoaveb (Post 3723418)

My car made Specialty Z's Instagram page. :happydance:
https://www.instagram.com/p/BeKIpuljVDU/

redondoaveb

01-20-2018 06:03 PM

Quote:

Originally Posted by brucelidat (Post 3723468)

Is this about what we should be expecting from the kit? Do you ave a dyno you can post?

I think topgunz could better answer the first question. If you scroll through the 4 pages of the instagram link you'll see dyno results.

brucelidat

01-20-2018 06:09 PM

nice, man

Senna-F1

01-20-2018 06:16 PM

1 Attachment(s)

Quote:

Originally Posted by brucelidat (Post 3723468)

Is this about what we should be expecting from the kit? Do you ave a dyno you can post?

Here you go.

redondoaveb

01-20-2018 06:21 PM

Quote:

Originally Posted by brucelidat (Post 3723475)

nice, man

Thank you

overtureZ

01-23-2018 06:58 PM

Aaron, did you get my PM about buying your leak test setup?

TopgunZ

01-23-2018 08:03 PM

http://www.the370z.com/members/topgu...3-19-49-42.png

Here you go. Get a 2.5" pvc cap. Schaeder valve, nut and a rubber washer. Make it look like this. Place it in the intercooler inlet. Pressurize it with compressor. Call me with questions.

overtureZ

01-24-2018 11:08 AM

Think a bike pump will work?

TopgunZ

01-24-2018 11:21 AM

Quote:

Originally Posted by overtureZ (Post 3724432)

Think a bike pump will work?

Well, you wouldnt need to get on the treadmill afterwards. :tup:

All times are GMT -5. The time now is 04:24 PM.

Page 150 of 187

« First