BP V 2.0 turbo kits...ROUND 3 place your order now

jax4557 · 05-05-2016, 11:37 PM

Quote:

Originally Posted by Boosted Performance

I am trying really hard to get #10 and #11 shipped tomorrow. Most of the stuff is packed up already, I just need to finish the manifolds for you guys.

If not tomorrow, it will go out on Monday next week for sure, which means it will arrive at your door on Friday the 13th.

No problems Sasha, we are just being children about having to wait. Speaks volumes about your kit in my opinion.

I know anyone who buys your kit feels the same as us at some point waiting

TcRocket · 05-05-2016, 03:21 PM

Lmfao I know I was

Sent from my Nexus 6P using Tapatalk

solidus · 05-05-2016, 03:26 PM

Now that I think about it, I asked Sasha to send it straight to my buddy's shop so I gotta go there and open up the boxes.

jwick · 05-06-2016, 06:56 AM

1150s? On a stock block?

TheWeez · 05-07-2016, 11:16 AM

Yea my idle is rough with the 3" pipes and 750s already

https://vimeo.com/165695521

Sent from my iPhone using Tapatalk

jwick · 05-07-2016, 11:49 AM

Best thing I did for my idle was completely remove the O2 sensors.

jax4557 · 05-07-2016, 06:29 PM

Quote:

Originally Posted by solidus

Make sure you explain the nature of the RJM clutch before the install if you have one. If you dont, you're gonna set it up again on your own and they're gonna have the worst time ever trying to bleed it.

I didnt get this right now but I will look into adding one later on.

Quote:

Originally Posted by jwick

Even for E85 and a future block I think 1150s are overkill. Guys are making into the 700whp with 1000s.

I could be wrong but I don't think the car will even idle with 1150s and the stock map. You tripled the injector size so it's going to triple the fuel its dumping.

I plan to push for 800 HP TQ on E85 in the future on the block so I just wanted to make sure I wasn't at the top of the duty cycle on injectors.

If nothing else I will do install and everything but injectors and charge pipes and run in garage to check for leaks,etc.

Guess ill be towing to tuner.

jwick · 05-07-2016, 10:16 PM

Quote:

Originally Posted by jax4557

I didnt get this right now but I will look into adding one later on.

I plan to push for 800 HP TQ on E85 in the future on the block so I just wanted to make sure I wasn't at the top of the duty cycle on injectors.

If nothing else I will do install and everything but injectors and charge pipes and run in garage to check for leaks,etc.

Guess ill be towing to tuner.

I hope you have a really good tuner. You are likely to have issues running 1150s on stock block.

TopgunZ · 05-07-2016, 10:59 PM

What are the issues? I maxed my 1000s out with both kits. My first being stock block. Might even still have that stock block if I went with 1150s.

solidus · 05-09-2016, 12:25 PM

Hey guys, for everyone that's done oil temp and oil pressure gauges , is there any adapter I need to get both gauge sensors connected outside of what's provided in the kit? I want to make sure I have those on hand so I don't have to hit the brakes waiting on parts to arrive. I'm running Oil Press, Oil Temp and Wideband in the stock pod and I actually have the gauges drop in ready minus the wiring harnesses. I had bought a salvage cluster on ebay and took that apart to set the gauges up so I just pop the oems out ( actuall break them up )and drop the new ones in.

jwick · 05-09-2016, 02:08 PM

You will need an additional Tee to take oil pressure from the factory location. It'll just be one more fitting added to where the turbo oil takeoff is for the kit. Sasha supplied that for me for a minor adder in cost.

Oil temperature is a little more difficult. You need a location to take it from. I'm currently teed off right before it enters the oil cooler. I had to buy a bunch of AN fittings and some brass plumbing fittings from Home Depot to make it work. Next time I pull the bumper I'm relocating that probe to my Phunk baffled oil pan.

solidus · 05-09-2016, 03:00 PM

Quote:

Originally Posted by jwick

You will need an additional Tee to take oil pressure from the factory location. It'll just be one more fitting added to where the turbo oil takeoff is for the kit. Sasha supplied that for me for a minor adder in cost.

Oil temperature is a little more difficult. You need a location to take it from. I'm currently teed off right before it enters the oil cooler. I had to buy a bunch of AN fittings and some brass plumbing fittings from Home Depot to make it work. Next time I pull the bumper I'm relocating that probe to my Phunk baffled oil pan.

Thanks man, starting ebay search now.

TcRocket · 05-09-2016, 03:04 PM

https://www.amazon.com/gp/aw/d/B000F...?ie=UTF8&psc=1

This is the T I used and I bought a 1/8" nipple

Sent from my Nexus 6P using Tapatalk

jax4557 · 05-09-2016, 06:29 PM

Im moving on to preparing for gauges.

Since im going to run ecutek and need the stock oil temp gauge can it be rewired or extended down into the nav cubby? If it can I will probably junk the volt and time gauges up top and put three new gauges in there ( real oil temp, oil pressure, fuel pressure)

I think im going to run the AEM 30-4900 AFR in the A pillar along with a turbosmart Eboost2.

On a side not I am running E85 but wouldn't need a gauge since it seems I can hijack the stock oil temp to display ethanol content on the fly?

Open to any suggestions, changes or new gauges.

Thanks guys,

jwick · 05-09-2016, 07:57 PM

Quote:

Originally Posted by jax4557

Im moving on to preparing for gauges.

Since im going to run ecutek and need the stock oil temp gauge can it be rewired or extended down into the nav cubby? If it can I will probably junk the volt and time gauges up top and put three new gauges in there ( real oil temp, oil pressure, fuel pressure)

I think im going to run the AEM 30-4900 AFR in the A pillar along with a turbosmart Eboost2.

On a side not I am running E85 but wouldn't need a gauge since it seems I can hijack the stock oil temp to display ethanol content on the fly?

Open to any suggestions, changes or new gauges.

Thanks guys,

I was under the impression that you can't divide up the stock gauges, either they all stay or all go.

05-06-2016, 06:56 AM	#4 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465058	1150s? On a stock block? __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-07-2016, 11:16 AM	#5 (permalink)
TheWeez Base Member Join Date: Oct 2015 Location: Tampa Posts: 246 Drives: 370Z PG 6M ST Rep Power: 25	BP V 2.0 turbo kits...ROUND 3 place your order now Yea my idle is rough with the 3" pipes and 750s already https://vimeo.com/165695521 Sent from my iPhone using Tapatalk __________________ "It's not fast enough" - Edgar J. Hoover

05-07-2016, 11:49 AM	#6 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465058	Best thing I did for my idle was completely remove the O2 sensors. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-07-2016, 10:59 PM	#9 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6836	What are the issues? I maxed my 1000s out with both kits. My first being stock block. Might even still have that stock block if I went with 1150s. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

05-09-2016, 02:08 PM	#11 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465058	BP V 2.0 turbo kits...ROUND 3 place your order now You will need an additional Tee to take oil pressure from the factory location. It'll just be one more fitting added to where the turbo oil takeoff is for the kit. Sasha supplied that for me for a minor adder in cost. Oil temperature is a little more difficult. You need a location to take it from. I'm currently teed off right before it enters the oil cooler. I had to buy a bunch of AN fittings and some brass plumbing fittings from Home Depot to make it work. Next time I pull the bumper I'm relocating that probe to my Phunk baffled oil pan. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-05-2016, 03:21 PM	#2 (permalink)
TcRocket Base Member Join Date: Sep 2015 Location: Coldwater MI Posts: 165 Drives: 2010 370z Nismo Rep Power: 11	Lmfao I know I was Sent from my Nexus 6P using Tapatalk

05-05-2016, 03:26 PM	#3 (permalink)
solidus Track Member Join Date: Oct 2014 Location: Orlando, Florida Posts: 694 Drives: 15' Nismo Black 6MT Rep Power: 10082	Now that I think about it, I asked Sasha to send it straight to my buddy's shop so I gotta go there and open up the boxes.

05-09-2016, 12:25 PM	#10 (permalink)
solidus Track Member Join Date: Oct 2014 Location: Orlando, Florida Posts: 694 Drives: 15' Nismo Black 6MT Rep Power: 10082	Hey guys, for everyone that's done oil temp and oil pressure gauges , is there any adapter I need to get both gauge sensors connected outside of what's provided in the kit? I want to make sure I have those on hand so I don't have to hit the brakes waiting on parts to arrive. I'm running Oil Press, Oil Temp and Wideband in the stock pod and I actually have the gauges drop in ready minus the wiring harnesses. I had bought a salvage cluster on ebay and took that apart to set the gauges up so I just pop the oems out ( actuall break them up )and drop the new ones in.

05-09-2016, 03:04 PM	#13 (permalink)
TcRocket Base Member Join Date: Sep 2015 Location: Coldwater MI Posts: 165 Drives: 2010 370z Nismo Rep Power: 11	https://www.amazon.com/gp/aw/d/B000F...?ie=UTF8&psc=1 This is the T I used and I bought a 1/8" nipple Sent from my Nexus 6P using Tapatalk

05-09-2016, 06:29 PM	#14 (permalink)
jax4557 Base Member Join Date: Nov 2014 Location: Jacksonville Posts: 102 Drives: 2014 370z Sport M6 Rep Power: 12	Im moving on to preparing for gauges. Since im going to run ecutek and need the stock oil temp gauge can it be rewired or extended down into the nav cubby? If it can I will probably junk the volt and time gauges up top and put three new gauges in there ( real oil temp, oil pressure, fuel pressure) I think im going to run the AEM 30-4900 AFR in the A pillar along with a turbosmart Eboost2. On a side not I am running E85 but wouldn't need a gauge since it seems I can hijack the stock oil temp to display ethanol content on the fly? Open to any suggestions, changes or new gauges. Thanks guys,

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Your favorite place to order wire online?	madwi	The Lounge (Off Topic)	11	06-22-2014 10:29 AM
anyone know a place in the GTA that makes CUSTOM body kits?	Z11	Canada	3	07-10-2012 05:53 PM
Can't place order for new Z	texunsam	Nissan 370Z Pricing / Ordering Discussions	9	01-28-2011 06:27 PM
OEM spoiler... best place to order from? Any non-OEM alternatives?	rl in florida	Exterior & Interior	1	12-18-2009 12:23 PM