EVO-R Carbon Fiber front lip - Preview Teaser

VaGntlmn · 10-29-2010, 10:05 AM

I just sent EVOR a PM asking for the 1 piece cf lip!!!

PapoZalsa · 10-30-2010, 08:47 PM

Here is mine but I got from a different vendor and cheaper:

NewYorkJon34 · 10-30-2010, 08:53 PM

What different vendor? It's an evo-r product unless you got it from the Z store

Cmike2780 · 11-01-2010, 08:31 PM

Some nightime pics:

Cmike2780 · 11-03-2010, 04:34 PM

Wrote this up for somebody and thought it might be helpful to others:

Installing is easy but just take your time. As with any aftermarket body parts install, test fit everything first.

-Clean the all the piece and apply double sided tape.

-Clean the bumper with some Bug & Tar remover and make sure there is no residue left over.

-Install one of the side pieces first, not the center. It should line up pretty well with the bumper's lines. Attach with just the double sided tape.

-The center piece is next. This is a key step. Peel off just enough tape
backing so you can peel it off with the center piece set flush to the bumper later on. You want to be able to adjust the center piece from side to side, so don't fully apply it to the bumper just yet.

-Have a friend hold the center piece in place while you put the other side piece on (again with just double sided tape). The side pieces will hold the center piece in place.

-Center the "center piece" so the gaps on either side are equal and peel off the rest of the tape backing.

-Step back and admire for a minute

Not done yet.

-You will need to jack-up the car to put the screws in. The factory jack works fine if you do one side at a time.

-Using a 1/16" drill bit or any drill bit slightly smaller than the provided screws, carefully drill out some pilot holes into the bumper using the holes already on the lip as a guide.

-The provided screws are self tapping. Using a hand screw driver only (no power tools!) tighten until flush.

-All done, enjoy!

kenchan · 11-03-2010, 04:41 PM

i use rubbing alcohol to remove any wax before i apply any adhesives.

also heat it very well... like ambient temps over 75F and let it cure at least 24hrs.
best if you can get the mounting surface very warm (almost hot) to the touch using the sun or IR heater/heat gun.

no water, no rain, etc. keep it dry for 24hrs.

Chris_1 · 11-03-2010, 11:31 PM

Why dont people remove the stock bottom sport lip thing< I feel like it looks odd with this lip, and I bet it would flow better if that piece wasnt their.

ddvette9 · 11-03-2010, 11:43 PM

anyone not have to paint the black side pieces. are they holding up okay?

Boost_lee · 11-03-2010, 11:55 PM

I didnt paint mine, cross your fingers lol. It's only been a few days of driving though.

98intrigue · 11-04-2010, 01:35 PM

Quote:

Originally Posted by Chris@WheelsDirectOnline.com

Why dont people remove the stock bottom sport lip thing< I feel like it looks odd with this lip, and I bet it would flow better if that piece wasnt their.

Yeah... after seeing my pictures, I started to wonder how it would look without the sport lip.

ddvette9 · 11-04-2010, 02:06 PM

thezstore left out my screws. what kinda screws do i need to go get and how many. Someone please chime in

phunk · 11-10-2010, 03:22 PM

trying to buy this... dont see it on thezstores website... and cant get ahold of evo-r (website down and no PM replys)

i could order it on ebay i guess but it costs more there... the first post of this thread shows it as a bit less expensive. ideas?

Cmike2780 · 11-10-2010, 03:45 PM

Quote:

Originally Posted by phunk

trying to buy this... dont see it on thezstores website... and cant get ahold of evo-r (website down and no PM replys)

i could order it on ebay i guess but it costs more there... the first post of this thread shows it as a bit less expensive. ideas?

The Z store has it under new items.

Linked here: The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts: Latest 370Z Products

WhiskeyHotel · 11-10-2010, 03:46 PM

The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts: EVO-R Front Lip, Type II, 09-10 370Z

EVOR · 11-10-2010, 04:43 PM

Sorry guys, my Domain has expired. Trying to get it back. I'm in Mexico now...

10-29-2010, 10:05 AM	#886 (permalink)
VaGntlmn Enthusiast Member Join Date: May 2010 Location: Centreville, Va Age: 63 Posts: 377 Drives: '10 Tour/Sport, 6MT Rep Power: 15	I just sent EVOR a PM asking for the 1 piece cf lip!!! __________________ Bill 2010 370z; Tour/Sport; 6mt; BlackCherry/Grey; 318 rwhp; 265 lbs rwtq. To view a list of my mods, click here; To view a photo journal of the mods, click here.

10-30-2010, 08:47 PM	#887 (permalink)
PapoZalsa A True Z Fanatic Join Date: Nov 2009 Location: Not in Sunny Florida Posts: 6,358 Drives: 16 Nismo w/Tech Pack Rep Power: 4499	Here is mine but I got from a different vendor and cheaper: __________________ 2009 370Z MB Base w/Sport Package 6MT Modshack's Custom Air Intakes /3M Clear Bra/ Illuminated Kick Plates / F. I CBE w/12" resonators / EVO-R Front Lip / Rear Hatch Wing / Tein S-Tech Springs /Ilegal Tint in the Rep. of VA/4x20mm Z1 Spacers/ Vinyl Roof/Liquid Carbon Designs Last edited by PapoZalsa; 10-30-2010 at 08:50 PM.

11-01-2010, 08:31 PM	#889 (permalink)
Cmike2780 A True Z Fanatic Join Date: Jun 2010 Location: Long Island Posts: 5,059 Drives: slowwww Rep Power: 29	Some nightime pics: __________________ [09][MB][6-Spd MT][Touring][Stillen Gen III][K&N][Borla CBE][Evo-R] [ArchitTEK Photography]

11-03-2010, 04:34 PM	#890 (permalink)
Cmike2780 A True Z Fanatic Join Date: Jun 2010 Location: Long Island Posts: 5,059 Drives: slowwww Rep Power: 29	Wrote this up for somebody and thought it might be helpful to others: Installing is easy but just take your time. As with any aftermarket body parts install, test fit everything first. -Clean the all the piece and apply double sided tape. -Clean the bumper with some Bug & Tar remover and make sure there is no residue left over. -Install one of the side pieces first, not the center. It should line up pretty well with the bumper's lines. Attach with just the double sided tape. -The center piece is next. This is a key step. Peel off just enough tape backing so you can peel it off with the center piece set flush to the bumper later on. You want to be able to adjust the center piece from side to side, so don't fully apply it to the bumper just yet. -Have a friend hold the center piece in place while you put the other side piece on (again with just double sided tape). The side pieces will hold the center piece in place. -Center the "center piece" so the gaps on either side are equal and peel off the rest of the tape backing. -Step back and admire for a minute Not done yet. -You will need to jack-up the car to put the screws in. The factory jack works fine if you do one side at a time. -Using a 1/16" drill bit or any drill bit slightly smaller than the provided screws, carefully drill out some pilot holes into the bumper using the holes already on the lip as a guide. -The provided screws are self tapping. Using a hand screw driver only (no power tools!) tighten until flush. -All done, enjoy! __________________ [09][MB][6-Spd MT][Touring][Stillen Gen III][K&N][Borla CBE][Evo-R] [ArchitTEK Photography]

11-10-2010, 03:22 PM	#897 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,659 Drives: 370 Rep Power: 954590	trying to buy this... dont see it on thezstores website... and cant get ahold of evo-r (website down and no PM replys) i could order it on ebay i guess but it costs more there... the first post of this thread shows it as a bit less expensive. ideas? __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

10-30-2010, 08:53 PM	#888 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	What different vendor? It's an evo-r product unless you got it from the Z store

11-03-2010, 04:41 PM	#891 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141520	i use rubbing alcohol to remove any wax before i apply any adhesives. also heat it very well... like ambient temps over 75F and let it cure at least 24hrs. best if you can get the mounting surface very warm (almost hot) to the touch using the sun or IR heater/heat gun. no water, no rain, etc. keep it dry for 24hrs.

11-03-2010, 11:31 PM	#892 (permalink)
Chris_1 Track Member Join Date: Mar 2010 Location: Statewide Posts: 838 Drives: Nissan 370Z Roadster Rep Power: 16	Why dont people remove the stock bottom sport lip thing< I feel like it looks odd with this lip, and I bet it would flow better if that piece wasnt their.

11-03-2010, 11:43 PM	#893 (permalink)
ddvette9 Track Member Join Date: May 2009 Location: Florida Posts: 823 Drives: 2013 Scion FRS Rep Power: 17	anyone not have to paint the black side pieces. are they holding up okay?

11-03-2010, 11:55 PM	#894 (permalink)
Boost_lee A True Z Fanatic Join Date: Feb 2009 Location: SATX Posts: 2,813 Drives: 09 370Z TT 6MT Rep Power: 29	I didnt paint mine, cross your fingers lol. It's only been a few days of driving though.

11-04-2010, 02:06 PM	#896 (permalink)
ddvette9 Track Member Join Date: May 2009 Location: Florida Posts: 823 Drives: 2013 Scion FRS Rep Power: 17	thezstore left out my screws. what kinda screws do i need to go get and how many. Someone please chime in

11-10-2010, 03:46 PM	#899 (permalink)
WhiskeyHotel Track Member Join Date: Nov 2009 Location: Oklahoma Posts: 530 Drives: 2015 GT-R PW Premium Rep Power: 16	The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts: EVO-R Front Lip, Type II, 09-10 370Z

11-10-2010, 04:43 PM	#900 (permalink)
EVOR A True Z Fanatic Join Date: Sep 2009 Location: New York Posts: 1,647 Drives: 09 Nismo 370Z #80 Rep Power: 44	Sorry guys, my Domain has expired. Trying to get it back. I'm in Mexico now... __________________ WWW.EVO-R.NET

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
carbon fiber front liecense area cover	darkseed	Nissan 370Z General Discussions	9	03-05-2010 06:55 AM
Carbon Fiber front fascia?	kannibul	Exterior & Interior	21	09-30-2009 01:19 AM
Sneak Peak, Carbon Fiber Front Lip, From The 370ZSOURCE!!!!	Michael@TheZStore	Exterior & Interior	31	04-19-2009 12:51 PM