NST (NonStopTuning) 370Z VQ37HR Pulley Kit Review w/ Dyno Charts

NonStopTuning · 04-17-2011, 02:12 PM

Quote:

Originally Posted by wstar

I put Stillen's underdrive pulley on my car ages ago (been on for 14K miles now btw, no issues at all with it, just FYI for those scared of pulleys). I'd rather stick with the Stillen one since it's already on the car, but I might try out your 10% overdriven alternator pulley just to bring my alternator back up to speed a bit (since I'm running that tiny PC680 battery as well).

Anyone have a clue about how belt fitment would work out on that combo? I'm guessing the tensioner can make up the difference using the belt length Stillen specified, doesn't look like a huge change on that little alternator pulley.

Using our alternator pulley would be a good idea with your setup. And yes, you can keep the same belt that you are using now. A shorter belt would not be necessary with your setup.

wstar · 05-02-2011, 10:02 PM

Quote:

Originally Posted by NonStopTuning

Using our alternator pulley would be a good idea with your setup. And yes, you can keep the same belt that you are using now. A shorter belt would not be necessary with your setup.

Just an update on this in case anyone else was considering this idea (adding NST's alternator pulley to an existing Stillen crank pulley): it works out fine with the belt Stillen recommends for their crank pulley (Gates K070776). The tension indicator on the tensioner shows up on the middle mark, which is just barely in range for a new belt according to the service manual (and then you still have some allowance for the belt to wear out over time).

NonStopTuning · 05-11-2011, 03:03 AM

Quote:

Originally Posted by wstar

Just an update on this in case anyone else was considering this idea (adding NST's alternator pulley to an existing Stillen crank pulley): it works out fine with the belt Stillen recommends for their crank pulley (Gates K070776). The tension indicator on the tensioner shows up on the middle mark, which is just barely in range for a new belt according to the service manual (and then you still have some allowance for the belt to wear out over time).

Good to go!

quicksilver08 · 08-12-2011, 09:13 AM

Quote:

Originally Posted by wstar

Just an update on this in case anyone else was considering this idea (adding NST's alternator pulley to an existing Stillen crank pulley): it works out fine with the belt Stillen recommends for their crank pulley (Gates K070776). The tension indicator on the tensioner shows up on the middle mark, which is just barely in range for a new belt according to the service manual (and then you still have some allowance for the belt to wear out over time).

Just ordered this belt from O'reilly's. Cost me $50.

XwChriswX · 08-12-2011, 09:19 AM

What is the belt number so I can go pick one up this afternoon?

wstar · 08-12-2011, 09:37 AM

Well the K070776 is what I used because I have a mixed pulley set (NST's OD alternator + my old Stillen UD crank that I had already installed ages ago). It's the same one you use with just Stillen's UD, and was still in range.

NST seems to recommend K070786, which is a very slightly longer belt (and their UD pulley is a little bit bigger, so that makes sense).

Check the belt tensioner's marks after install and you'll know if everything's kosher on belt tension (service manual page EM-13).

08-12-2011, 09:19 AM	#5 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 452	What is the belt number so I can go pick one up this afternoon? __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

08-12-2011, 09:37 AM	#6 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3595	Well the K070776 is what I used because I have a mixed pulley set (NST's OD alternator + my old Stillen UD crank that I had already installed ages ago). It's the same one you use with just Stillen's UD, and was still in range. NST seems to recommend K070786, which is a very slightly longer belt (and their UD pulley is a little bit bigger, so that makes sense). Check the belt tensioner's marks after install and you'll know if everything's kosher on belt tension (service manual page EM-13). __________________ 7AT Track Car! Journal thread / Car setup details

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
STILLEN Longtube G3 Intakes. Review, Dyno and Impressions.	RCZ	Intake/Exhaust	270	06-03-2015 02:25 PM
Stillen Underdrive Pulley - Review/Pics/Dyno/Vid	semtex	Engine & Drivetrain	73	11-24-2014 01:25 AM
Stillen Headers installed - Review/Pics/Vid/Dyno	semtex	Intake/Exhaust	120	06-25-2014 12:15 PM
Turbo-kits.com VQ37HR TT kit	nq23	Forced Induction	21	06-07-2009 12:25 PM
JWT Pop Chargers - Pictures - Review - Dyno	RCZ	Intake/Exhaust	31	03-30-2009 09:50 AM