QuickJack Lift System

JARblue · 05-18-2016, 09:27 AM

Quote:

Originally Posted by TBatt

I measured about 16.5 inches of clearance. You could get maybe another inch or two by adding in a piece of wood to the rubber lift block but that is about it. When I installed my FI CBE I had plenty of room to work under the car. I think you could drop the tranny but it would be by brute arm strength as there would be no room for a tranny jack.

Later this year when I do the clutch upgrade I'm planning on having it done by a local shop. I'm getting to old to do that kind of lifting. Back when I was in the USAF, I took the tranny out of my 1969 Volvo 142S by parking the car with two wheels on the curb. Where there is a will, there is a way. Especially when you are dead broke.

The Quickjack is still a great tool to have in the shop. There are lots and lots of things that you can use if for but major work is not going to be easy.

The specs on their website say you can get up to 20" of lift with stacked blocks. It's more of a convenient alternative to floor jack and jack stands. It's definitely not a lift that will allow for major engine and transmission works as you mention.

The transmission jack I got from HF had no problems holding the trans under the car during a CSC replacement. Even at 16.5" it would have been a tight fit but probably still doable.

squid267 · 05-18-2016, 01:31 PM

Aw man, back to the drawing board. Thanks for the info.

YzGyz · 05-18-2016, 04:54 PM

Maybe use the QJ to lift the car on jack stands. Then drop the QJ and add some 2x12 under them (maybe 2 layers worth to give an extra 3.5"). Turn lift the car again with the QJ now sitting on a higher foundation. The 2x will not crush and will be damn stable. That's potentially 21". I'd even screw the 2x together for more stability.

YzGyz

squid267 · 05-23-2016, 08:54 AM

Quote:

Originally Posted by YzGyz

Maybe use the QJ to lift the car on jack stands. Then drop the QJ and add some 2x12 under them (maybe 2 layers worth to give an extra 3.5"). Turn lift the car again with the QJ now sitting on a higher foundation. The 2x will not crush and will be damn stable. That's potentially 21". I'd even screw the 2x together for more stability.

YzGyz

Not a bad idea at all! Will report back with what I end up doing!

Edit: Did some searching and I found this on a porsche forum.

TBatt · 05-19-2016, 01:53 PM

Good idea, simple and cheap!

ramoszx12r · 05-28-2016, 05:11 PM

Any one have the 7000, and will it work on the Z. I will like to use it on my SUV to.

TBatt · 06-03-2016, 12:56 PM

Yesterday I used my QuickJack to lift my wife's Toyota Matrix. The A/C drain had gotten clogged up and I ran a coat hanger wire through it. Unfortunately that didn't reach correctly so I had to pull the glove box out to get to the drain. Finally got it cleared out with some compressed air. I bet a gallon of water drained out of there!

While the car was jacked up I went ahead and did an oil change. The lift still works like a champ! Each time I use it it takes less time to setup.

Next week is the Super Charger install so it will get a work out once again. I plan on keeping the car on the lift the whole time so that I don't have to bend over so far to work on it. Us old guys need all the help we can get!

TreeSemdyZee · 06-03-2016, 05:49 PM

Quote:

Originally Posted by TBatt

Yesterday I used my QuickJack to lift my wife's Toyota Matrix. The A/C drain had gotten clogged up and I ran a coat hanger wire through it. Unfortunately that didn't reach correctly so I had to pull the glove box out to get to the drain. Finally got it cleared out with some compressed air. I bet a gallon of water drained out of there!

While the car was jacked up I went ahead and did an oil change. The lift still works like a champ! Each time I use it it takes less time to setup.

Next week is the Super Charger install so it will get a work out once again. I plan on keeping the car on the lift the whole time so that I don't have to bend over so far to work on it. Us old guys need all the help we can get!

I had to clear the drain on a Toyota that I used to drive.
Note to anyone planning on doing this. Don't lay under the drain with your mouth open when trying to clear the clog.

YzGyz · 06-03-2016, 04:44 PM

I bet you still smile every time you press the button and the car starts to fly. I do when I lift my car. I always think, "Damn this is easy! Why didn't I get his years ago!"

YzGyz

TBatt · 06-04-2016, 04:15 PM

Quote:

Originally Posted by YzGyz

I bet you still smile every time you press the button and the car starts to fly. I do when I lift my car. I always think, "Damn this is easy! Why didn't I get his years ago!"

YzGyz

Amen, brother!

TBatt · 06-12-2016, 09:40 PM

Here I am using the QJ to install my new supercharger! I used the lower setting so I don't have to bend over so far while working under the hood. Works great!!

YzGyz · 06-13-2016, 02:03 AM

Looking darn good!! I'm curious how a supercharged z feels like. I might have to try and trade keys with a local if I find a willing local.

YzGyz

TBatt · 07-19-2016, 02:17 PM

Quote:

Originally Posted by YzGyz

Looking darn good!! I'm curious how a supercharged z feels like. I might have to try and trade keys with a local if I find a willing local.

YzGyz

While I have yet to do any WOT pulls, it is feeling like a caged beast! Half to three quarter throttle pulls are a blast. So far I have only gotten in the 4 psi range but you CAN FEEL IT! I'm having the car remote tuned so it is a slow process but I have the best guy out there doing the tune and I will follow his directions to the letter. I want this tune right.

What is so cool about this setup is that it drives very much like it did stock except for a much more sensitive throttle response. After a little practice with the new throttle feel, I can drive it so anyone riding with me would not know the potential of the car.

TBatt · 06-15-2016, 01:29 PM

With the 9 psi pulley and TopgunZ's air to air intercooler mod, I'm hoping for around 450 rwhp. The EcuTek dyno tune is scheduled for the 25th. It should be a blast!

TBatt · 08-08-2016, 05:23 PM

First dyno pull was 400whp. The boost was 8.4 psi which is lower than expected so I'm in search of a leak. The boost should be around 10 psi. The car is still a beast.

Now that the car is fast I needed to slow it down as well. I used my QJ this weekend to install the Akebono sport brakes. They sure look good with the red calipers!

I can now setup the QJ from a stored location in about 5-7 minutes. It really is a Quick Jack!

05-18-2016, 04:54 PM	#3 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 64	Maybe use the QJ to lift the car on jack stands. Then drop the QJ and add some 2x12 under them (maybe 2 layers worth to give an extra 3.5"). Turn lift the car again with the QJ now sitting on a higher foundation. The 2x will not crush and will be damn stable. That's potentially 21". I'd even screw the 2x together for more stability. YzGyz Zbrah likes this. __________________ http://www.the370z.com/members-370z-...gyzs-turn.html YzGyz

05-19-2016, 01:53 PM	#5 (permalink)
TBatt Track Member Join Date: Apr 2013 Location: Huntsville, AL Posts: 832 Drives: 2019 GT-R Rep Power: 20170	Good idea, simple and cheap! __________________ RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE!

05-28-2016, 05:11 PM	#6 (permalink)
ramoszx12r Track Member Join Date: Sep 2015 Location: Carneys point NJ Posts: 665 Drives: 16 370Z Nismo White. Rep Power: 1429	Any one have the 7000, and will it work on the Z. I will like to use it on my SUV to. __________________ Tony Ramos

06-03-2016, 12:56 PM	#7 (permalink)
TBatt Track Member Join Date: Apr 2013 Location: Huntsville, AL Posts: 832 Drives: 2019 GT-R Rep Power: 20170	Yesterday I used my QuickJack to lift my wife's Toyota Matrix. The A/C drain had gotten clogged up and I ran a coat hanger wire through it. Unfortunately that didn't reach correctly so I had to pull the glove box out to get to the drain. Finally got it cleared out with some compressed air. I bet a gallon of water drained out of there! While the car was jacked up I went ahead and did an oil change. The lift still works like a champ! Each time I use it it takes less time to setup. Next week is the Super Charger install so it will get a work out once again. I plan on keeping the car on the lift the whole time so that I don't have to bend over so far to work on it. Us old guys need all the help we can get! YzGyz, Memphis370Z, old guy and 1 others like this. __________________ RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE!

06-03-2016, 04:44 PM	#9 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 64	I bet you still smile every time you press the button and the car starts to fly. I do when I lift my car. I always think, "Damn this is easy! Why didn't I get his years ago!" YzGyz TBatt likes this. __________________ http://www.the370z.com/members-370z-...gyzs-turn.html YzGyz

05-18-2016, 01:31 PM	#2 (permalink)
squid267 Base Member Join Date: May 2013 Location: Worcester, MA Posts: 207 Drives: 12 Nismo 370Z PW M6 Rep Power: 40	Aw man, back to the drawing board. Thanks for the info.

06-13-2016, 02:03 AM	#12 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 64	Looking darn good!! I'm curious how a supercharged z feels like. I might have to try and trade keys with a local if I find a willing local. YzGyz __________________ http://www.the370z.com/members-370z-...gyzs-turn.html YzGyz

06-15-2016, 01:29 PM	#14 (permalink)
TBatt Track Member Join Date: Apr 2013 Location: Huntsville, AL Posts: 832 Drives: 2019 GT-R Rep Power: 20170	With the 9 psi pulley and TopgunZ's air to air intercooler mod, I'm hoping for around 450 rwhp. The EcuTek dyno tune is scheduled for the 25th. It should be a blast! __________________ RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
KW HLS (Hydraulic Lift System)	CLOUD10	Brakes & Suspension	45	02-09-2017 10:18 AM
Too low to lift car	laricb	Brakes & Suspension	18	01-07-2012 03:12 PM
Garage Lift System	maxtodorov	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	9	06-05-2010 06:26 PM