Only one: HFC, Gen3 Intake, or CBE?

sensi09 · 06-17-2009, 02:24 PM

Quote:

Originally Posted by in.the.dark

Where's the option for the ECU flash? If you are serious about performance, that is your best bet. My first call will likely be to Technosquare for a 93 octane specific performance map.

If you don't care as much, anything you have is fine because the change in sound/performance will likely satisfy your i-modified-my-car jones.

If you're going somewhere like technosquare, it will be more cost-effective to get all bolt-ons done prior to doing a reflash.

semtex · 06-17-2009, 02:32 PM

Quote:

Originally Posted by sensi09

If you're going somewhere like technosquare, it will be more cost-effective to get all bolt-ons done prior to doing a reflash.

I was about to say the same thing. Getting a reflash prior to completing all your bolt-ons is a complete waste of money.

spearfish25 · 06-17-2009, 03:20 PM

Thanks guys, definitely appreciating the advice and look forward to anyone elses opinions.

I haven't found any clips of Berk HFCs alone. At this point, I have no problem with having a louder exhaust as long as my car doesn't sound like a rice cooker. Do the HFCs alone have a nasty buzz or does the sound mature with some time to keep a good, sporty note?

As you noted, the HFCs are cost effective and none of these bolt-ons sound like a challenging install.

semtex · 06-17-2009, 04:10 PM

Quote:

Originally Posted by spearfish25

Thanks guys, definitely appreciating the advice and look forward to anyone elses opinions.

I haven't found any clips of Berk HFCs alone.

What?? Get with the program, man!

YouTube - Project 370Z Sound Clip - Berk Technology High Flow Cats

YouTube - Project 370Z Dyno Test: Berk Technology High Flow Cats

Scribe · 06-18-2009, 09:22 AM

Quote:

Originally Posted by semtex

I was about to say the same thing. Getting a reflash prior to completing all your bolt-ons is a complete waste of money.

Semtex, you can disagree all you want, but the fact of the matter is that changing the tune first will yield good gains. In addition, much of the gains in power from the aftermarket intakes isn't from additional airflow, the stockers flow just fine, it is actually from changing the MAF signal to read less air is flowing and thus leans out the charge to a more ideal ratio. Those disputed tests where the guys at 370z.com held the air-fuel ratio at stock levels proved that the power gained from additional flow was minimal. This points to where the intakes make most of their real power, which is changing the reading and thus the combustion mixture, not from additional airflow. If you were to take a stock 370z and flash it, you will see good gains.

And as further proof, this has been done and tested at 370zdotcom.

Had they gone with a better map, their gains would have been greater.

View Poll Results: Which bolt-on should be done first (most bang for the buck)?
Stillen Gen3 Intake	9	18.75%
Berk HFCs	27	56.25%
Stillen CBE	8	16.67%
Don't do anything unless you're doing more than one.	4	8.33%
Voters: 48. You may not vote on this poll

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust	axio	Intake/Exhaust	82	07-31-2009 12:41 PM
Nismo intake??	JonnieN	Intake/Exhaust	1	06-08-2009 06:26 PM
Intake?	AG370z	Intake/Exhaust	5	05-10-2009 08:37 PM
New Intake/Exhausts	BPAuto	Intake/Exhaust	10	03-18-2009 07:58 PM

06-17-2009, 03:20 PM	#3 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1858	Thanks guys, definitely appreciating the advice and look forward to anyone elses opinions. I haven't found any clips of Berk HFCs alone. At this point, I have no problem with having a louder exhaust as long as my car doesn't sound like a rice cooker. Do the HFCs alone have a nasty buzz or does the sound mature with some time to keep a good, sporty note? As you noted, the HFCs are cost effective and none of these bolt-ons sound like a challenging install.