AAM Intake Manifold Q

phunk · 02-04-2020, 02:26 PM

Never heard of a stock manifold failure. Im sure it will eventually let go if you keep increasing boost pressure.

Your signature says youre running 800ftlb torque.. that is approaching (if not well-in) the danger-zone for VQ headgaskets. You could be an exception. But if you are looking to stay on the safe side of things, I wouldnt be worried about your intake manifold I would be worried about your headgaskets.

Spooler · 02-04-2020, 03:06 PM

Quote:

Originally Posted by phunk

Never heard of a stock manifold failure. Im sure it will eventually let go if you keep increasing boost pressure.

Your signature says youre running 800ftlb torque.. that is approaching (if not well-in) the danger-zone for VQ headgaskets. You could be an exception. But if you are looking to stay on the safe side of things, I wouldnt be worried about your intake manifold I would be worried about your headgaskets.

700ft/lb at 4550 RPM and mine were done. It appears the higher the RPM the peak TQ is, the lesser of a problem it is.

phunk · 02-04-2020, 03:28 PM

Quote:

Originally Posted by Spooler

700ft/lb at 4550 RPM and mine were done. It appears the higher the RPM the peak TQ is, the lesser of a problem it is.

There could be some correlation, but I would be surprised if its extremely significant. Perhaps there is some resonant frequency or something occurring somewhere in the upper range that is rocking the cylinders. I would say that torque output is a far less convoluted indication of cylinder pressures than horsepower (torque at higher RPM) or boost levels.

Just because yours failed at 700 doesnt mean it couldnt hold 800-900-1000, or could have failed eventually at 600. Dont forget the fatigue and wear factor. Just like we can run a stock engine at 800 for a while... it will eventually fail, but when it does, you might only be running 600 at that moment.

Hotrodz · 02-04-2020, 05:53 PM

Quote:

Originally Posted by phunk

Never heard of a stock manifold failure. Im sure it will eventually let go if you keep increasing boost pressure.

Your signature says youre running 800ftlb torque.. that is approaching (if not well-in) the danger-zone for VQ headgaskets. You could be an exception. But if you are looking to stay on the safe side of things, I wouldnt be worried about your intake manifold I would be worried about your headgaskets.

Actually there was a guy on the forum several years ago Hojin and he had his manifold fail at least twice at 25 and 26 psi. I believe he was at 9:1 compression.

Sent from my SM-G965U using Tapatalk

phunk · 02-04-2020, 06:23 PM

Quote:

Originally Posted by Hotrodz

Actually there was a guy on the forum several years ago Hojin and he had his manifold fail at least twice at 25 and 26 psi. I believe he was at 9:1 compression.

Sent from my SM-G965U using Tapatalk

Compression ratio wouldn’t make a difference. 25-26 is pretty high for a VQ, as they will generally be nearly 1000whp by then if the turbo system is staying efficient. Probably an exceptional case. Seems like 1000hp is right on the tipping point in more ways than one.

Hotrodz · 02-04-2020, 06:30 PM

Quote:

Originally Posted by phunk

Compression ratio wouldn’t make a difference. 25-26 is pretty high for a VQ, as they will generally be nearly 1000whp by then if the turbo system is staying efficient. Probably an exceptional case. Seems like 1000hp is right on the tipping point in more ways than one.

Agreed, and that is what he was pushing.

Sent from my SM-G965U using Tapatalk

GeauxTigers1 · 02-04-2020, 07:13 PM

Quote:

Originally Posted by Hotrodz

Actually there was a guy on the forum several years ago Hojin and he had his manifold fail at least twice at 25 and 26 psi. I believe he was at 9:1 compression.

Sent from my SM-G965U using Tapatalk

I miss Hojin! Dude became a Dad and then *poof*. lol

I hadn't realized he had his manifold blow, wonder what he did to correct the issue. I'd imagine if it did crack, it's not a devastating repair.

Hotrodz · 02-04-2020, 08:10 PM

Quote:

Originally Posted by GeauxTigers1

I miss Hojin! Dude became a Dad and then *poof*. lol

I hadn't realized he had his manifold blow, wonder what he did to correct the issue. I'd imagine if it did crack, it's not a devastating repair.

He never recovered after the last failure. He said he was going get the car up and running again and then he had another baby.

Spooler · 02-05-2020, 11:31 AM

Quote:

Originally Posted by Hotrodz

He never recovered after the last failure. He said he was going get the car up and running again and then he had another baby.

Hopefully he still has it and didn't sell it.

GeauxTigers1 · 02-04-2020, 07:11 PM

Quote:

Originally Posted by Spooler

I wouldn't do a GTR manifold conversion. The runners are too long and will cause issues in the midrange.

Yea as Bob (hotrodz) mentioned, if it aint broke, don't fix it. lol. I was trying to fix BEFORE it broke but it sounds like many are having great look with the OEM manifold. Really appreciate the feedback all that the stock manifold can hang

Quote:

Originally Posted by phunk

Never heard of a stock manifold failure. Im sure it will eventually let go if you keep increasing boost pressure.

Your signature says youre running 800ftlb torque.. that is approaching (if not well-in) the danger-zone for VQ headgaskets. You could be an exception. But if you are looking to stay on the safe side of things, I wouldnt be worried about your intake manifold I would be worried about your headgaskets.

Wouldn't the closed deck and the Cosworth upgraded Head Gasket help with that?

phunk · 02-04-2020, 07:33 PM

Quote:

Originally Posted by GeauxTigers1

Yea as Bob (hotrodz) mentioned, if it aint broke, don't fix it. lol. I was trying to fix BEFORE it broke but it sounds like many are having great look with the OEM manifold. Really appreciate the feedback all that the stock manifold can hang

Wouldn't the closed deck and the Cosworth upgraded Head Gasket help with that?

They may help or extend the life of the headgasket seal, but we have discovered they are not an end-all fix for the 1000+ HP VQ. They are still letting go in that power range.

GeauxTigers1 · 02-05-2020, 11:50 AM

Quote:

Originally Posted by phunk

They may help or extend the life of the headgasket seal, but we have discovered they are not an end-all fix for the 1000+ HP VQ. They are still letting go in that power range.

We talking whp range or base? Really liking being able to keep the Z at that 875whp Mark. It’s so beautiful. Lol

phunk · 02-05-2020, 02:10 PM

Quote:

Originally Posted by GeauxTigers1

We talking whp range or base? Really liking being able to keep the Z at that 875whp Mark. It’s so beautiful. Lol

Since its a gray area you could consider it either/or. 875whp is beyond what some cars have lost headgaskets at already.

Spooler · 02-05-2020, 02:22 PM

Quote:

Originally Posted by GeauxTigers1

We talking whp range or base? Really liking being able to keep the Z at that 875whp Mark. It’s so beautiful. Lol

Just be aware, it can cost you 20k if a headgasket let's go and a long wait. You may get lucky and have no block damage which means it will be cheaper if you want the same result. It's a crap shoot.

Spooler · 02-04-2020, 07:38 PM

Quote:

Originally Posted by GeauxTigers1

Yea as Bob (hotrodz) mentioned, if it aint broke, don't fix it. lol. I was trying to fix BEFORE it broke but it sounds like many are having great look with the OEM manifold. Really appreciate the feedback all that the stock manifold can hang

Wouldn't the closed deck and the Cosworth upgraded Head Gasket help with that?

Bob sold him his GTR manifold upgrade a long time ago. LOL
As far as the Cosworth head gasket. There is a better quality one out there. Seb knows which one it is. I gave that info to him and he ordered one to check it out. He liked it from what I gathered.

02-04-2020, 02:26 PM	#1 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,669 Drives: 370 Rep Power: 974725	Never heard of a stock manifold failure. Im sure it will eventually let go if you keep increasing boost pressure. Your signature says youre running 800ftlb torque.. that is approaching (if not well-in) the danger-zone for VQ headgaskets. You could be an exception. But if you are looking to stay on the safe side of things, I wouldnt be worried about your intake manifold I would be worried about your headgaskets. GeauxTigers1, Rusty and Spooler like this. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph Last edited by phunk; 02-04-2020 at 02:42 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] $500 both Stillen Gen 3 intake & Z1 Upper Intake Manifold	SC370	Parts for sale (Private Classifieds)	3	10-08-2018 02:52 PM
[FOR SALE] Motordyne 370z Intake Manifold and NEW OEM Lower Intake	Carbon_z	Parts for sale (Private Classifieds)	3	07-10-2018 04:34 PM
3" Short Intake + M370 Manifold vs 3" CAI + Z1 Manifold Dyno Comparison	MoncefVQ	Intake/Exhaust	11	02-26-2018 01:21 PM
[FOR SALE] (BNIB) OEM Intake Manifold Gaskets///Exhaust Manifold Gaskets	BlkNismo	Parts for sale (Private Classifieds)	19	08-13-2016 12:01 PM
selling used stillen G3 intake.Motordyne M370 Intake Manifold	01206	Canada	4	04-14-2016 01:31 AM