Pulleys

redondoaveb · 11-05-2019, 09:08 AM

Quote:

Originally Posted by BOLIO 671

Sounds like a great idea....I’ll reach out to him before we send the charger out to 928. Thanks again Pat. If the waste gate doesn’t happen what pulleys would I need to change out to get up to 13psi? I’m currently at about 8 to 8.3psi with the 9lb SC pulley that Stillen sent me which is on the Jack-Serp side. This low boost has tk die wit my location, weather and sea level factors

I used the 9lb and a 2.85 supercharger pulley to get to 13 psi (12.86 to be exact). You'll have to go to a 3.00 idler on the supercharger side if you go with the 2.85.

BOLIO 671 · 11-06-2019, 12:44 AM

Quote:

Originally Posted by redondoaveb

I used the 9lb and a 2.85 supercharger pulley to get to 13 psi (12.86 to be exact). You'll have to go to a 3.00 idler on the supercharger side if you go with the 2.85.

Awesome... Will these pulley changes require the spacers mentioned by Cupcakez? I know it was mentioned earlier On the thread I believe by by imazman that it was a pretty tight fit on the idler pulley (SC Side).

"Z"en · 11-06-2019, 06:18 PM

Quote:

Originally Posted by BOLIO 671

Awesome... Will these pulley changes require the spacers mentioned by Cupcakez? I know it was mentioned earlier On the thread I believe by by imazman that it was a pretty tight fit on the idler pulley (SC Side).

As long as you do not change the jackshaft pulley on the supercharger side, you won't need the spacers. You may need the RPM belt instead if your goal is 13psi and you put the filter on, depending on the belt tension and impeller.

redondoaveb · 11-06-2019, 06:28 PM

Quote:

Originally Posted by BOLIO 671

Awesome... Will these pulley changes require the spacers mentioned by Cupcakez? I know it was mentioned earlier On the thread I believe by by imazman that it was a pretty tight fit on the idler pulley (SC Side).

As mentioned by"Z"en, you won't need spacers unless you change the jackshaft pulley, sc side. Also, the idler wasn't a tight fit at all. No issues using the 3" idler.

TopgunZ · 11-06-2019, 07:12 AM

Remember that your SC will not come with a warranty if you send it to 928. If you send it to Vortech and get the Si impeller then it does come with a warranty.

redondoaveb · 11-06-2019, 06:24 PM

Quote:

Originally Posted by TopgunZ

Remember that your SC will not come with a warranty if you send it to 928. If you send it to Vortech and get the Si impeller then it does come with a warranty.

Good point. It's too bad Vortech won't do ceramic bearings in the V3 though.

BOLIO 671 · 11-07-2019, 03:12 AM

Quote:

Originally Posted by redondoaveb

Good point. It's too bad Vortech won't do ceramic bearings in the V3 though.

This was my next question.

"Z"en · 11-07-2019, 04:22 AM

Quote:

Originally Posted by BOLIO 671

This was my next question.

Mine is Vortech Si with ceramic bearings (928 internal).

11-06-2019, 07:12 AM	#5 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Remember that your SC will not come with a warranty if you send it to 928. If you send it to Vortech and get the Si impeller then it does come with a warranty. BOLIO 671, wideglideleon, Senna-F1 and 1 others like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unorthodox Racing Crank Pulley VS Stock Crank Pulley (weight only)	bewhitey	Engine & Drivetrain	3	08-25-2017 07:26 PM
I wanna pound the shyt outta Demi Lovato.	UNKNOWN_370	Movies / Celebrity Gossip / Entertainment / Music	4	08-01-2016 08:32 AM
Pulley	paratrooper	Engine & Drivetrain	8	05-19-2014 12:20 PM
NST Pulley	dimitarm	Intake/Exhaust	27	05-06-2014 06:51 AM