![]() |
I shared this in another P1239 thread, but I figured I would share this here since this is apparently the main and well-linked thread I have a 2007 HR 350z
|
|||||||
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
|
#1 (permalink) |
|
Base Member
Join Date: Nov 2013
Location: DC
Posts: 28
Drives: 2007 350z
Rep Power: 13 ![]() |
I shared this in another P1239 thread, but I figured I would share this here since this is apparently the main and well-linked thread
I have a 2007 HR 350z now at about 60K mileage. Three years ago (Summer 2016), I had a local shop install the a Stillen/Vortech supercharger. I have some non-HP supporting mods in the engine, hi-flow cats, and a motordyne exhaust. I wanted a conservative tune since this my daily driver and only car, I have about 400 rwhp and 315 tq. Performance wise I'm very happy with it, and I don't abuse the car. Fun highway driving only. However, I have had multiple problems with the kit. Problem 1: Bad Throttle cables A few months after I bought it, Stillen came out with upgraded Throttle Body Extension cables but deigned not to mass inform their customers. These cables were improved to have a much thicker gauge since the original ones were crimping. Crimping may, and in my case did, cause the engine to not turn on, or go into 'limp mode'. We had to buy the new upgraded cables for $140 and install them. Still, this required a tow and a few days down time. All sets bought post winter 2016 will have these new cables Problem 2: Heat/EMI problems Maybe about 6-12 months after that, it happened again. Was driving just fine, the next morning for work, car turns on, then heavily lurches, dashboard is now a xmas tree. I get it towed to same shop, the check engine light is a P1239 code. This is a very famous code for this error, its all over google and Z forums. After conducting forum research, the 'new' cables Stillen provided still are susceptible to heat and electrical interference, so a heat/EMI sleeve was placed over the cables. Problem 3: Now ******* what? This morning (May 14 2019), the car went into limp mode again. Jesus ****ing christ what now? After several attempted restarts all fail, I call a tow. An hour later, the second the tow gets here, I start up car just fine and it seems perfect, like nothing is wrong albeit with check engine light. It's in the shop now, they are looking at it. So overall, I'm kinda not that happy with Stillen. The performance is great, but this is my only car, so I care more about reliability. Something is seriously wrong with their electrical division, but its the same problem now 3 ****ing times over the past few years. |
|
|
|
|
|
#2 (permalink) |
|
Base Member
Join Date: Jul 2010
Location: Fort Worth TX
Posts: 23
Drives: 10 370Z Sport PW MT
Rep Power: 16 ![]() |
I started this thread. I had a guy run a stop sign & T-bone me Nov. 2018 totalling the Z with 190k miles on it. Only issue I ever had was this p1239 code & limp. Stillen uses a Bosch recirc. valve. I replaced that valve with a turbosmart dual port BOV. Once I dialed the BOV in, I had far fewer issues with the p1239. When I would tighten up the BOV I would get the codes again. When I ran it loose, I had far fewer problems. I read once where Stillen runs the TS BOV on thier red SC car .... ps. when it goes limp, sometimes it will take 10-20 restarts before it will take throttle in neutral. Hit the start button & immeadiately start pumping the gas pedal, if it is limp, turn it off & try again until it revs properly, then get back on the road. My car never 'stranded' me .... just super anoying & made you NEVER want to have a passenger with you. I can almost promise you, if you run an adjustable BOV & it is adjusted too tight, you will be going limp like crazy. The Bosch recirc. valve from the kit will also go limp. I will say that all the cable/foil wrap/heat shielding never cured the problem as well as the Turbosmart dual-port BOV set at the loosest setting where idle vacuum would barely shut the piston. On boost the valve would shut fully from boost pressure, so no worries there. ALSO, NISSAN is to BLAME for the car going LIMP, not Stillen. This car should throw the code & engine light ONLY. Not sure why Nissan decides to KILL the car.
__________________
GTM STAGE II TT, EXTERNAL WASTEGATES, FI 3" TDX, BLITZ EBC, SZ HIGH 5, FI 500E FUEL RETURN, WALBRO 525, ID1050, ZEIT FLEXFUEL E85, SD TUNED with ECUTEK by SEB, SZ HIGH 5 CLUTCH, 2014 NISMO GUNMETAL WHEELS, 2015 NISMO FRONT, REAR, & SIDE SKIRTS Last edited by wymoteeZ; 05-15-2019 at 01:09 PM. |
|
|
|
![]() |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| P1239 throttle position sensor | ThamerZ370 | Tuning | 5 | 12-19-2015 12:47 PM |
| [WTB] stillen supercharger | mathys92 | Parts for sale (Private Classifieds) | 0 | 03-02-2015 08:03 AM |
| [FOR SALE] Stillen supercharger kit | mr-emv | Parts for sale (Private Classifieds) | 11 | 09-07-2013 11:07 AM |
| FS: Stillen Supercharger kit | Elysium | Canada | 11 | 03-31-2012 08:05 AM |
| Stillen or gtm supercharger? | germanattitud | Forced Induction | 34 | 08-07-2011 01:47 PM |