Turbosmart Dual Port BPV With Stillen Kit

x2o · 11-23-2015, 04:16 PM

Okay so today I took out the BPV included by stillen (plastic

) and put in the turbosmart dual port valve, and the extra soft blue spring that I've read people had to use. After a lot of slight turns dialing in the adjustment, i finally got a strong steady idle.

I noticed that when the valve wasn't quite dialed in, I wouldn't get the initial gauge sweep even though no SES lights or anything came on. I got it in a position now where it idles steady and gives me the gauge sweep and all.

However, when I free rev the engine, it still bogs down just a little below idle. Since I'm so close I don't want to adjust it the wrong way and lose the steady idle lol. Should I tighten or loosen it bit by bit to get it right?

Appreciate any possible help

TopgunZ · 11-23-2015, 05:03 PM

Gauge sweep? You don't have your bpv hooked to a gauge do you?

x2o · 11-23-2015, 05:07 PM

Quote:

Originally Posted by TopgunZ

Gauge sweep? You don't have your bpv hooked to a gauge do you?

No, by gauge sweep I'm referring to the tach/oil temp/voltage when you first power the car on. they go from min to max except they didn't when the idle was rough.

Not sure if this means anything even, just thought I'd mention

x2o · 11-23-2015, 05:19 PM

Is it possible it requires a retune compared to the bosch style bpv? I feel like it's so close but I just can't get it perfect

gonna bring the laptop out tomorrow and grab a data log

StillenZ84 · 11-23-2015, 06:07 PM

Just keep turning it 1/2 a turn more and more hard until it doesn't dip below idle. Its really easy to adjust. Do you have a a/f gauge?

x2o · 11-23-2015, 06:38 PM

Quote:

Originally Posted by StillenZ84

Just keep turning it 1/2 a turn more and more hard until it doesn't dip below idle. Its really easy to adjust. Do you have a a/f gauge?

Okay sounds like I've been on the right track then. I don't have an a/f or boost gauge yet, been using uprev to log a/f although I know that's not the most accurate method.

Wanted to make sure that tighter was the way to go

StillenZ84 · 11-23-2015, 06:43 PM

Cool. Yeah you are on the right path. You are probably 1/2 turn to 1 1/2 turns from being spot on from the sounds of it.

x2o · 11-23-2015, 07:35 PM

Think I got it ! Went just a bit less than 1 full turn (1/4 turn at a time) and now it seems to be holding steady after rev. Will take it for a datalog and test drive tomorrow

Love the sound!

Guess I made the thread a bit hastily, was panicking when I couldn't get it after a few hours of tweaking lol.

Thanks

StillenZ84 · 11-23-2015, 08:06 PM

Good deal. Hey I was the same way when I first installed mine.

BOLIO 671 · 11-23-2015, 09:45 PM

Quote:

Originally Posted by x2o

Is it possible it requires a retune compared to the bosch style bpv?

I would also like to know this about the retune....I have read about this upgrade... Still trying to grip it all...I know that the BPV on the Stillen unit just recirculates the excess boost back into the system versus changing out to the Turbosmart Dual BOV allows you to vent to atmosphere.....so the question I have Is it just cosmetic/aesthetic for sound, or does it improve performance over the bosch style By Pass Valve....There's been different opinions about this....I know a handful of guys have done it and recall Diego@Vossen citing that Kyle Millen even had this upgrade on his Black 370Z....but Stillen never really gave a clear answer on the performance aspect of the BPV vs BOV....

Do any of you have a pic of where this part goes when replacing the stillen unit?

TopgunZ · 11-23-2015, 10:06 PM

Your plastic bosch one is good up to 10psi. You can take the hoses off too but it will run like crap just like the turbosmart one would if you don't put the recirc hoses on.

Unless your going 11+ psi then it's just for sound.

StillenZ84 · 11-23-2015, 10:18 PM

Yep exactly what Top said. Unless you plan on the impeller upgrade or smaller pulleys it is basically just for sound. It is definitely a higher quality part for sure though. Billet aluminum vs. plastic. Don't know how accurate or true this is but my former tuner told me that it also helps to release some heat from the intake tube that the supercharger produces. Sounds like it makes sense but don't know that it is proven.

TopgunZ · 11-23-2015, 10:29 PM

Why would that make sense? Unless he is saying that since its metal it is acting as a heat sink and draws heat away from the pipe, the pipe that is in a very hot engine bay.

Doesn't make sense to me.

zmanelite · 11-23-2015, 10:46 PM

I have one on my set up and Stillen actually had to retune the car with it till it worked properly with the Stillen SC

StillenZ84 · 11-23-2015, 11:42 PM

Yeah top he could have just been blowing smoke but it sounded legit at the time. Made it sound like opening the door to an oven would help the temperature of the air inside the intake decrease.

11-23-2015, 04:16 PM	#1 (permalink)
x2o Base Member Join Date: Aug 2015 Location: Florida Posts: 80 Drives: Boosted 370z Rep Power: 242	Turbosmart Dual Port BPV With Stillen Kit Okay so today I took out the BPV included by stillen (plastic ) and put in the turbosmart dual port valve, and the extra soft blue spring that I've read people had to use. After a lot of slight turns dialing in the adjustment, i finally got a strong steady idle. I noticed that when the valve wasn't quite dialed in, I wouldn't get the initial gauge sweep even though no SES lights or anything came on. I got it in a position now where it idles steady and gives me the gauge sweep and all. However, when I free rev the engine, it still bogs down just a little below idle. Since I'm so close I don't want to adjust it the wrong way and lose the steady idle lol. Should I tighten or loosen it bit by bit to get it right? Appreciate any possible help __________________ 2011 370z Supercharged Sport Touring 7AT Stillen: Supercharger Kit \| Cat Back/TP \| Oil/AT Coolers GTM: Hardened 7AT (valve body+torque converter) Whiteline: 27mm Front \| 24mm Rear \| Swift Springs

11-23-2015, 05:03 PM	#2 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6833	Gauge sweep? You don't have your bpv hooked to a gauge do you? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

11-23-2015, 05:19 PM	#4 (permalink)
x2o Base Member Join Date: Aug 2015 Location: Florida Posts: 80 Drives: Boosted 370z Rep Power: 242	Is it possible it requires a retune compared to the bosch style bpv? I feel like it's so close but I just can't get it perfect gonna bring the laptop out tomorrow and grab a data log __________________ 2011 370z Supercharged Sport Touring 7AT Stillen: Supercharger Kit \| Cat Back/TP \| Oil/AT Coolers GTM: Hardened 7AT (valve body+torque converter) Whiteline: 27mm Front \| 24mm Rear \| Swift Springs Last edited by x2o; 11-23-2015 at 05:23 PM.

11-23-2015, 06:07 PM	#5 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Just keep turning it 1/2 a turn more and more hard until it doesn't dip below idle. Its really easy to adjust. Do you have a a/f gauge? __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

11-23-2015, 06:43 PM	#7 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Cool. Yeah you are on the right path. You are probably 1/2 turn to 1 1/2 turns from being spot on from the sounds of it. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

11-23-2015, 07:35 PM	#8 (permalink)
x2o Base Member Join Date: Aug 2015 Location: Florida Posts: 80 Drives: Boosted 370z Rep Power: 242	Think I got it ! Went just a bit less than 1 full turn (1/4 turn at a time) and now it seems to be holding steady after rev. Will take it for a datalog and test drive tomorrow Love the sound! Guess I made the thread a bit hastily, was panicking when I couldn't get it after a few hours of tweaking lol. Thanks StillenZ84 likes this. __________________ 2011 370z Supercharged Sport Touring 7AT Stillen: Supercharger Kit \| Cat Back/TP \| Oil/AT Coolers GTM: Hardened 7AT (valve body+torque converter) Whiteline: 27mm Front \| 24mm Rear \| Swift Springs

11-23-2015, 08:06 PM	#9 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Good deal. Hey I was the same way when I first installed mine. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

11-23-2015, 10:06 PM	#11 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6833	Your plastic bosch one is good up to 10psi. You can take the hoses off too but it will run like crap just like the turbosmart one would if you don't put the recirc hoses on. Unless your going 11+ psi then it's just for sound. BOLIO 671 and StillenZ84 like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

11-23-2015, 10:18 PM	#12 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Yep exactly what Top said. Unless you plan on the impeller upgrade or smaller pulleys it is basically just for sound. It is definitely a higher quality part for sure though. Billet aluminum vs. plastic. Don't know how accurate or true this is but my former tuner told me that it also helps to release some heat from the intake tube that the supercharger produces. Sounds like it makes sense but don't know that it is proven. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

11-23-2015, 10:29 PM	#13 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6833	Why would that make sense? Unless he is saying that since its metal it is acting as a heat sink and draws heat away from the pipe, the pipe that is in a very hot engine bay. Doesn't make sense to me. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

11-23-2015, 10:46 PM	#14 (permalink)
zmanelite Track Member Join Date: Nov 2013 Location: Anaheim Posts: 753 Drives: 370 Z Nismo Rep Power: 36	I have one on my set up and Stillen actually had to retune the car with it till it worked properly with the Stillen SC __________________ Instagram @zmanscm

11-23-2015, 11:42 PM	#15 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Yeah top he could have just been blowing smoke but it sounded legit at the time. Made it sound like opening the door to an oven would help the temperature of the air inside the intake decrease. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] NEW JERSEY.. Stillen G3 Intake AND Stillen Dual Exhaust	Gman91111	Parts for sale (Private Classifieds)	15	09-13-2013 01:25 AM
[FOR SALE] Stillen Dual Exhaust & Stillen front plate holder Pick up in Bay Area	A7594217	Parts for sale (Private Classifieds)	17	08-04-2013 11:27 PM
STILLEN Stillen Gen 3 Ultra Long Tube Dual Intake Kit Nissan 370Z	alright	Forced Induction	4	03-20-2013 02:38 PM
Berk HFC's, Stillen Intake, and a Stillen Dual Exhaust....	2theextreme	The Lounge (Off Topic)	8	06-18-2009 10:01 PM