-_-CarbonSignal Rear Spoiler-_-

Wiggins3377 · 12-28-2012, 10:48 AM

Quote:

Originally Posted by Huan'z

What is the best way to install this add on spoiler? Double sided type? Any suggestion guys!!

Id suggest 3m double sided tape and some 3m adhesive promotor wipes. The promotor wipes are key if you want to make sure the spoiler, front lip and rear diffuser stay on the car. I may be able to grab some of the wipes if you need them. Just send me a PM if you need some.

Huan'z · 12-28-2012, 11:07 AM

Quote:

Originally Posted by Wiggins3377

Id suggest 3m double sided tape and some 3m adhesive promotor wipes. The promotor wipes are key if you want to make sure the spoiler, front lip and rear diffuser stay on the car. I may be able to grab some of the wipes if you need them. Just send me a PM if you need some.

So I need to go Home Depot to get 3d sided tape and the 3m adhesive promoter. Clean the surface with promoter then apply the double sided tape? Let me know buddy. Thanks a lot!!

kinda worries about the front and the rear lip. The rear need to be partial paint before the install. How much does it cost to paint 2 sides of the rear lip? Any idea? Thanks a lot guys!!

KaienZ34 · 02-02-2013, 05:13 PM

Quote:

Originally Posted by Huan'z

What is the best way to install this add on spoiler? Double sided type? Any suggestion guys!!

So how did it turn out? Did you get it all installed?

GaleForce · 12-28-2012, 10:34 AM

Get some Norton SpeedGrip or something like it (like 3M's version)

GaleForce · 12-28-2012, 11:09 AM

Hopefully your front lip fits better than mine. I had a 2" gap on the drivers side. There was no way double sided tape would hold that.

Huan'z · 12-28-2012, 11:16 AM

Quote:

Originally Posted by GaleForce

Hopefully your front lip fits better than mine. I had a 2" gap on the drivers side. There was no way double sided tape would hold that.

Are u serious buddy? 2"??? Then how u install it?

GaleForce · 12-28-2012, 11:28 AM

Quote:

Originally Posted by Huan'z

Are u serious buddy? 2"??? Then how u install it?

Very serious. They told me it would fit better if I tried to install it with the bumper off. It didn't. The fit was the same. I used Norton SpeedGrip and 6 clamps.

Check the link to my build thread in my sig for pictures.

Wiggins3377 · 12-28-2012, 11:28 AM

Quote:

Originally Posted by Huan'z

So I need to go Home Depot to get 3d sided tape and the 3m adhesive promoter. Clean the surface with promoter then apply the double sided tape? Let me know buddy. Thanks a lot!!

kinda worries about the front and the rear lip. The rear need to be partial paint before the install. How much does it cost to paint 2 sides of the rear lip? Any idea? Thanks a lot guys!!

Yeah, make sure you clean any area that will touch the double sided tape well before applying the promotor, then apply the promotor to that same area. You'll need a few packets of it for everything you’ll be installing. Id grab 10 or so just to be safe. You'll also want to test fit the pieces well before applying anything, cause once you use the promotor its near impossible to remove the pieces. I had alot of trouble installing my rear spats simply because of the flex in the bumper. Id suggest taking the whole rear bumper off to install the diffuser. It makes the whole process a lot easier. I’ll post a pic of what I did. As far as paint, id suggest painting the whole thing first, that’s what I did and it turned out fine.

Quote:

Originally Posted by GaleForce

Hopefully your front lip fits better than mine. I had a 2" gap on the drivers side. There was no way double sided tape would hold that.

I have the same carbon signal lip and had heard about gap issues as well, however I had mine professional molded to the front bumper. That said I wasn’t made aware of any fitment issues.

Wiggins3377 · 12-28-2012, 11:32 AM

Here's a pic. I used two saw horses and c clamps to hold it while the spats set.

Huan'z · 12-28-2012, 11:43 AM

Quote:

Originally Posted by Wiggins3377

Yeah, make sure you clean any area that will touch the double sided tape well before applying the promotor, then apply the promotor to that same area. You'll need a few packets of it for everything you’ll be installing. Id grab 10 or so just to be safe. You'll also want to test fit the pieces well before applying anything, cause once you use the promotor its near impossible to remove the pieces. I had alot of trouble installing my rear spats simply because of the flex in the bumper. Id suggest taking the whole rear bumper off to install the diffuser. It makes the whole process a lot easier. I’ll post a pic of what I did. As far as paint, id suggest painting the whole thing first, that’s what I did and it turned out fine.

I have the same carbon signal lip and had heard about gap issues as well, however I had mine professional molded to the front bumper. That said I wasn’t made aware of any fitment issues.

Good job buddy!!

I will do what u said. Will post picture when everything in place! Thanks a lot! Where can I get the promoter? Home Depot? Thanks a lot!!

Wiggins3377 · 12-28-2012, 11:57 AM

Quote:

Originally Posted by Huan'z

Good job buddy!!

I will do what u said. Will post picture when everything in place! Thanks a lot! Where can I get the promoter? Home Depot? Thanks a lot!!

I doubt home depot would have it. I also doubt autozone or a similar store would have it. Your best bet would be an automotive paint and supply specialty store. I think amazon has it as well. Like i said, if you need some let me know, there is a place not far from me that has it and i can grab it for you and put it in the mail tomorrow. They typically cost $3-$3.50 a packet.

GundamWZero · 01-14-2013, 10:07 PM

So whats the going price for this??

I want in.

CarbonSignal · 01-15-2013, 09:40 AM

send me your address on : carbonsignal@hotmail.com

Aznsensazn · 01-21-2013, 05:19 PM

Hi can I get a quote on this spoiler? Shipping to 77459, and can you give me a quote on both FRP and CF (N-Spec V2). Thank you.

TaylorRyan370 · 02-20-2013, 04:15 PM

PM for spoiler in CF shipped to 90620 Thanks!

12-28-2012, 10:34 AM	#4 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51866	Get some Norton SpeedGrip or something like it (like 3M's version) __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

12-28-2012, 11:09 AM	#5 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51866	Hopefully your front lip fits better than mine. I had a 2" gap on the drivers side. There was no way double sided tape would hold that. __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

01-14-2013, 10:07 PM	#12 (permalink)
GundamWZero Base Member Join Date: Jan 2013 Location: Ft. Bliss Posts: 21 Drives: '10 370Z Touring 7SP Rep Power: 14	So whats the going price for this?? I want in. __________________ SHIFT_ 2005/06 Nissan, Altima, 2007 Nissan Armada, 2010 Nissan 370Z

01-15-2013, 09:40 AM	#13 (permalink)
CarbonSignal A True Z Fanatic Join Date: Jan 2011 Location: Dubai/California Posts: 2,092 Drives: 370z Rep Power: 22	send me your address on : carbonsignal@hotmail.com __________________ CS 2018 Summer Nismo NEW GB............MOONBEAM Forum OFFER.....................09-14 CS Nismolipkit Forum OFFER Facebook.... Instagram ....Website

01-21-2013, 05:19 PM	#14 (permalink)
Aznsensazn Base Member Join Date: Dec 2012 Location: Texas Posts: 96 Drives: 12' PW Touring AT Rep Power: 14	Hi can I get a quote on this spoiler? Shipping to 77459, and can you give me a quote on both FRP and CF (N-Spec V2). Thank you. Last edited by Aznsensazn; 01-21-2013 at 05:24 PM.

02-20-2013, 04:15 PM	#15 (permalink)
TaylorRyan370 Enthusiast Member Join Date: Jan 2013 Location: Orange County, CA Posts: 285 Drives: 1969 Camaro Rep Power: 14	PM for spoiler in CF shipped to 90620 Thanks! __________________ Build Journal: 2012 370Z \| Magnetic Black \| Manual \| Sport Package

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB: Stock 370Z Hood, Rear Spoiler, Front spoiler	Mr350Z	Parts for sale (Private Classifieds)	7	03-12-2017 10:27 PM
CarbonSignal Amuse Rear installed	SeeyaBud86	Exterior & Interior	40	03-20-2011 10:20 AM
Rear spoiler?	Neo187H	Exterior & Interior	4	02-08-2010 09:40 PM
WTB: Stock 370 Hood, Rear Spoiler, Front spoiler	Mr350Z	Wanted	0	02-08-2010 07:19 PM
looking to buy PW rear spoiler	jookiyaya	Wanted	0	10-21-2009 07:25 AM

*-_-*CarbonSignal Rear Spoiler*-_-*

-_-CarbonSignal Rear Spoiler-_-