OEM shift knob removal (SEARCHED)

Liquid_G · 03-21-2011, 10:58 AM

Quote:

Originally Posted by FromG2Z

Thanks for the great idea. I might try that. Duct tape should be tacky enough that it won't slip, and I need to use enough layers to not indent the shift knob.

As far as the shift assembly, you lifted the console up and used vice grips right? So I'm assuming you pulled the boot down to expose the shifter surface, but did you use anything between the vise grips and the shifter itself? I tried a rag, but am experiencing slippage there too

Right, there was some sort of black ring down there or something that we used the vise grips on. I figured since its covered by the shift boot I didn't car about marring it up.. Just to be clear too I used Locking Vice grips, not just channel locks.

Also put a layer of masking tape first on the shift knob before the duct tape, help get the adhesive from the duct tape from stickying (is that a word) up the stock knob.

FromG2Z · 03-21-2011, 12:36 PM

Quote:

Originally Posted by Liquid_G

Right, there was some sort of black ring down there or something that we used the vise grips on. I figured since its covered by the shift boot I didn't car about marring it up.. Just to be clear too I used Locking Vice grips, not just channel locks.

Also put a layer of masking tape first on the shift knob before the duct tape, help get the adhesive from the duct tape from stickying (is that a word) up the stock knob.

Ok, I did some more research and came across this:

DIY Shift Boot Install

So I went ahead and purchased a strap wrench and those locking pliers. I needed the strap wrench for my oil filters anyways, so why not. So I might try this route... use the strap wrench on the shift knob to avoid marring it up.

So based on this picture below, is this also what you did? It looks like E-licous actually used the vise grip on the rubber boot ring, not on the shaft itself... Was that the same ring your were talking about? And you were certain that when your wife held the vise grip in place to the shifter shaft, it didn't slip or turn as you worked on the shift knob???

Liquid_G · 03-21-2011, 04:08 PM

Quote:

Originally Posted by FromG2Z

Ok, I did some more research and came across this:

DIY Shift Boot Install

So I went ahead and purchased a strap wrench and those locking pliers. I needed the strap wrench for my oil filters anyways, so why not. So I might try this route... use the strap wrench on the shift knob to avoid marring it up.

So based on this picture below, is this also what you did? It looks like E-licous actually used the vise grip on the rubber boot ring, not on the shaft itself... Was that the same ring your were talking about? And you were certain that when your wife held the vise grip in place to the shifter shaft, it didn't slip or turn as you worked on the shift knob???

Not 100% sure becuase I'm at work and can't see most pics (stupid fking websense web-filtering) I'll try to login in tonight and check. But I don't think it was on the boot ring.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: AT Shift knob removal/replacement	Imtired	DIY Section (Do-It-Yourself)	43	04-07-2016 10:24 AM
AT Knob Removal - Help.	chippy	Exterior & Interior	30	11-08-2010 02:58 PM
New Shift Knob... let's try this again!	m4a1mustang	Exterior & Interior	19	06-22-2009 06:41 PM
Shift knob HELp!	DJcuetip	Southern California Region	0	06-16-2009 06:58 AM
S2K Aluminum shift knob to replace OEM knob	initialgemini	Exterior & Interior	12	04-19-2009 02:56 PM