Future Release : ARK PERFORMANCE INC HFC & GRIP TYPE 2 v2

TeamARK · 02-02-2012, 03:41 PM

HFC samples are coming in next week. We will be releasing the HFC's for G37,370z, FX, 350z, and G35 all at once.

Alex

sixpax · 02-02-2012, 07:16 PM

Free bump ... added an "after" proper adjustment photo to my earlier post.

sixpax · 02-02-2012, 07:39 PM

...lower angle. Ignore the filthy car, but that is one SECKSI exhaust !

marrim · 02-02-2012, 11:49 PM

Quote:

Originally Posted by sixpax

Free bump ... added an "after" proper adjustment photo to my earlier post.

you sovled the issue by using the right tools. Jack stands are hard to get this aligned right. Lift so much easier. BTW Looks great.

bleufiend · 02-03-2012, 05:53 AM

So after having the exhaust on my car for two weeks I'll HIV an honest review of three ups and three downs.

Ups
1. Burnt tips with laser etching look good.
2. Loud when I get on it and quiet when I'm cruising.
3. Packaged very well when shipped so no damaged components when I recieved it.

Downs
1. The fitment still isn't right. The left and right side exhaust tips on mine can be made to sit even if I rotate the left side exhaust canister counter clockwise but then this causes it to hit the differential on rough roads or going over bumps.
2. The right side resonator flat layer on the rear body cross member no matter what and I had to trim it with a 2x2 inch cut to make the exhaust resonator not hit.
3. Ark you need to have better communication with your customers in the future about the progress of bringing a new product to market. Post in the vendor thread about where you are in getting te product and the process of getting it ready to ship to your paying customers. The original sale ad said eta before Christmas. Then that turned into the week between Christmas and new years which then became January followed by three different people promising the exhaust would ship the next day on three different phone calls.

All in all I'm satisfied with the exhaust and happy with my purchase save for having to modify cross member which I wasn't to comfy with. Thank you TeamArk for your commitment to our car and providing parts for it.

TeamARK · 02-03-2012, 04:16 PM

One more suggestion with the installation, Raise the Ypipe and bolt it down. There should be more than enough clearance on that.

bleufiend · 02-04-2012, 02:39 AM

I adjusted the y pipe up as far as I could and the right side resonator was still contacting. I may just be my car or I got one exhaust that the resonator was to far back. There was only one other guy I saw in this thread earlier on that had the same issue with the exhaust contacting the cross member.

TeamARK · 02-04-2012, 01:26 PM

That is the V1. You have the V2. All batch has been tested on our Jig here before it is shipped out.

To provide you better support, please email me some pictures to alex@arkperformanceusa.com

In addition, I will have my staff start on installation guides and videos to ensure perfect fitment.

Alex

bleufiend · 02-05-2012, 07:15 AM

Well I'll wait on your videos to show the process of adjustment. I've already had to cut the cross member but maybe I am missing something. Thank you for the effort.

pf62 · 02-05-2012, 08:11 AM

When mine were being put on the mid pipes were not labled left or right. The exhaust hit the cross member and the tips didn't line up until we switched them.

sixpax · 02-05-2012, 08:25 AM

Quote:

Originally Posted by pf62

When mine were being put on the mid pipes were not labled left or right. The exhaust hit the cross member and the tips didn't line up until we switched them.

Interesting. I thought mine had a little white label on it that said "DRIVERSIDE" but I could be mistaken.

MoChu · 02-05-2012, 12:28 PM

Same problem. Had to cut my cross member. Still can't align the tips

dozerdc · 02-05-2012, 05:45 PM

Pics of issue? Worried potential buyer here.

TeamARK · 02-06-2012, 12:15 PM

Please email us the pictures. alex@arkperformanceusa.com. There is no issues with the V2 whatsoever.

sixpax · 02-06-2012, 02:35 PM

Quote:

Originally Posted by G37sHKS

Why your making it soo complicated?

They all know how to install Catback, over 500 VHR cars with fast intention exhaust and none used what ever you wanna call it (guides and videos) and none of them had unbalanced mufflers...

And now Motordyne has come... none will have unbalanced mufflers.. mark my word

Not sure I get what your point is, but your post is rather uncalled for.

My fitment issues have been resolved to my satisfaction, and were caused by me not doing the installation correctly.

02-03-2012, 05:53 AM	#80 (permalink)
bleufiend Base Member Join Date: Jan 2011 Location: Miami, FL Posts: 200 Drives: 370z MB Spt/Tour 6sp Rep Power: 14	So after having the exhaust on my car for two weeks I'll HIV an honest review of three ups and three downs. Ups 1. Burnt tips with laser etching look good. 2. Loud when I get on it and quiet when I'm cruising. 3. Packaged very well when shipped so no damaged components when I recieved it. Downs 1. The fitment still isn't right. The left and right side exhaust tips on mine can be made to sit even if I rotate the left side exhaust canister counter clockwise but then this causes it to hit the differential on rough roads or going over bumps. 2. The right side resonator flat layer on the rear body cross member no matter what and I had to trim it with a 2x2 inch cut to make the exhaust resonator not hit. 3. Ark you need to have better communication with your customers in the future about the progress of bringing a new product to market. Post in the vendor thread about where you are in getting te product and the process of getting it ready to ship to your paying customers. The original sale ad said eta before Christmas. Then that turned into the week between Christmas and new years which then became January followed by three different people promising the exhaust would ship the next day on three different phone calls. All in all I'm satisfied with the exhaust and happy with my purchase save for having to modify cross member which I wasn't to comfy with. Thank you TeamArk for your commitment to our car and providing parts for it. __________________ Z34 owner formerly Z33. OZOC FTW.

02-04-2012, 02:39 AM	#82 (permalink)
bleufiend Base Member Join Date: Jan 2011 Location: Miami, FL Posts: 200 Drives: 370z MB Spt/Tour 6sp Rep Power: 14	I adjusted the y pipe up as far as I could and the right side resonator was still contacting. I may just be my car or I got one exhaust that the resonator was to far back. There was only one other guy I saw in this thread earlier on that had the same issue with the exhaust contacting the cross member. __________________ Z34 owner formerly Z33. OZOC FTW.

02-05-2012, 07:15 AM	#84 (permalink)
bleufiend Base Member Join Date: Jan 2011 Location: Miami, FL Posts: 200 Drives: 370z MB Spt/Tour 6sp Rep Power: 14	Well I'll wait on your videos to show the process of adjustment. I've already had to cut the cross member but maybe I am missing something. Thank you for the effort. __________________ Z34 owner formerly Z33. OZOC FTW.

02-05-2012, 12:28 PM	#87 (permalink)
MoChu Base Member Join Date: Aug 2009 Location: Colorado Posts: 108 Drives: Pearl NisSan 370z Rep Power: 15	Same problem. Had to cut my cross member. Still can't align the tips __________________ MoChu

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ARK Grip Type 2 - Review + Pics	detroadster	Intake/Exhaust	34	07-30-2013 03:03 AM
[FOR SALE] ARK Grip Type 2 CBE FS - South Jersey	TonyBPD	Parts for sale (Private Classifieds)	78	11-16-2011 08:06 PM
Just received the new Ark Type 2 Grip True Dual exhaust	Zeto	Intake/Exhaust	74	09-03-2011 03:10 AM
Some More updates on the Type 2 ARK GRIP Exhaust	TeamARK	Intake/Exhaust	3	08-23-2011 11:24 AM
FS: Ark Grip Type 2 Exhaust - NEW	Raven	Parts for sale (Private Classifieds)	26	02-07-2011 10:57 AM

02-02-2012, 03:41 PM	#76 (permalink)
TeamARK Track Member Join Date: Jul 2009 Location: CHINO Posts: 957 Drives: Black 350z/370z Rep Power: 16	HFC samples are coming in next week. We will be releasing the HFC's for G37,370z, FX, 350z, and G35 all at once. Alex

02-03-2012, 04:16 PM	#81 (permalink)
TeamARK Track Member Join Date: Jul 2009 Location: CHINO Posts: 957 Drives: Black 350z/370z Rep Power: 16	One more suggestion with the installation, Raise the Ypipe and bolt it down. There should be more than enough clearance on that.

02-04-2012, 01:26 PM	#83 (permalink)
TeamARK Track Member Join Date: Jul 2009 Location: CHINO Posts: 957 Drives: Black 350z/370z Rep Power: 16	That is the V1. You have the V2. All batch has been tested on our Jig here before it is shipped out. To provide you better support, please email me some pictures to alex@arkperformanceusa.com In addition, I will have my staff start on installation guides and videos to ensure perfect fitment. Alex

02-05-2012, 08:11 AM	#85 (permalink)
pf62 Base Member Join Date: Aug 2011 Location: Allentown,PA Posts: 42 Drives: 2010 370z 7at blk ch Rep Power: 13	When mine were being put on the mid pipes were not labled left or right. The exhaust hit the cross member and the tips didn't line up until we switched them.

02-05-2012, 05:45 PM	#88 (permalink)
dozerdc Base Member Join Date: Jan 2012 Location: DC Posts: 60 Drives: 09 370z Sport Rep Power: 13	Pics of issue? Worried potential buyer here.

02-06-2012, 12:15 PM	#89 (permalink)
TeamARK Track Member Join Date: Jul 2009 Location: CHINO Posts: 957 Drives: Black 350z/370z Rep Power: 16	Please email us the pictures. alex@arkperformanceusa.com. There is no issues with the V2 whatsoever.