Greddy Oil Pan

Neo187H · 04-28-2012, 02:00 PM

Quote:

Originally Posted by Baer383

I have a 25 row oil cooler,as far as air temps go ,I'm F.I so it wouldn't be the same.

Ah I thought you meant your oil temps were so low just from the oil pan, got me excited for a minute. Though ambient temp always matters as far as cool goes, the issue is just compounded when you add FI to the mix.

fuct · 04-28-2012, 02:09 PM

Quote:

Originally Posted by Neo187H

Ah I thought you meant your oil temps were so low just from the oil pan, got me excited for a minute. Though ambient temp always matters as far as cool goes, the issue is just compounded when you add FI to the mix.

yea no kidding. i was talking about adding it WITHOUT an oil cooler.

Baer383 · 04-28-2012, 02:15 PM

Quote:

Originally Posted by fuct

yea no kidding. i was talking about adding it WITHOUT an oil cooler.

You have to have a oil cooler at the very least to control oil temps,it should have been a red flag that Nissan put a oil "temp" gauge,

The reason why the oil temps are high is b/c the oil pan is very shallow so that most of the oil sits up inside the engine block with it being fed heat at a constant basis.

VSS370z · 04-28-2012, 08:10 PM

Thanks a lot guys for the info, just wanted to ask since i decided i want to start buying a few of the supporting mods first that are necessary or at least recommended for FI

ZBro16 · 05-17-2012, 12:19 PM

Anyone have this Greddy pan with the ZSpeed undershroud with the oil change access door? I'm guessing this won't fit with that on... but then again if the Greddy pan is made to fit underneath the stock undershould then it should fit. Thoughts?

Baer383 · 05-17-2012, 01:26 PM

Quote:

Originally Posted by ZBro16

Anyone have this Greddy pan with the ZSpeed undershroud with the oil change access door? I'm guessing this won't fit with that on... but then again if the Greddy pan is made to fit underneath the stock undershould then it should fit. Thoughts?

I have the Greddy pan and it fits with a stock splash shield,but it is close I was going to buy the Z speed under shroud but it is to close I thought it might rub so I didn't buy it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Greddy Turbo TI-C or Greddy Spectrum Elite?	Andy124	Intake/Exhaust	32	06-05-2011 02:34 PM
Greddy ti-c vs. Greddy se for (na's)	NizzyBoy	Intake/Exhaust	3	09-22-2010 12:16 PM
Greddy Tuner Turbo Kit - limited time special! - FREE Ti-C Greddy turbo exhaust!	GT Motoring	Forced Induction	2	07-17-2010 05:57 AM
Greddy Tuner Turbo Kit - limited time special! - FREE Ti-C Greddy turbo exhaust!	GT Motoring	Drivetrain/Engine	0	07-16-2010 07:26 PM
Greddy TT	Zsteve	Forced Induction	29	04-13-2010 10:09 PM

04-28-2012, 08:10 PM	#4 (permalink)
VSS370z Enthusiast Member Join Date: Apr 2012 Location: Puerto Rico Posts: 380 Drives: 09 Nissan 370z CY M6 Rep Power: 15	Thanks a lot guys for the info, just wanted to ask since i decided i want to start buying a few of the supporting mods first that are necessary or at least recommended for FI

05-17-2012, 12:19 PM	#5 (permalink)
ZBro16 Enthusiast Member Join Date: Nov 2011 Location: Huntsville, AL Posts: 370 Drives: A Z. Rep Power: 15	Anyone have this Greddy pan with the ZSpeed undershroud with the oil change access door? I'm guessing this won't fit with that on... but then again if the Greddy pan is made to fit underneath the stock undershould then it should fit. Thoughts?