Nissan 370Z Forum  

Innovate dlg1

Anyone running an innovate dlg1? How the heck did you get the wires routed through the firewall. I tried going the same way I have my fuel pump power wire

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain


Like Tree3Likes
  • 2 Post By madwi
  • 1 Post By Rusty

Reply
 
LinkBack Thread Tools Display Modes
Old 05-11-2021, 12:35 AM   #1 (permalink)
Enthusiast Member
 
Join Date: Nov 2016
Location: Washington
Posts: 285
Drives: 2014 Nismo
Rep Power: 27364
DrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond repute
Default Innovate dlg1

Anyone running an innovate dlg1? How the heck did you get the wires routed through the firewall. I tried going the same way I have my fuel pump power wire routed (behind the battery) but the connector is pretty thick, I would have to enlarge the hole a fair bit (there's two cables/connectors that must pass through, one for each bank o2 sensor).

DrBacon is offline   Reply With Quote
Old 05-11-2021, 12:39 AM   #2 (permalink)
A True Z Fanatic
 
madwi's Avatar
 
Join Date: Sep 2012
Location: West Michigan
Posts: 31,400
Drives: Granma red Z
Rep Power: 2684428
madwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond reputemadwi has a reputation beyond repute
Default

The large grommet behind the battery area is where I pass all my wires and crap through. Stole these pics from oil pressure gauge thread.


Rusty and DrBacon like this.
madwi is offline   Reply With Quote
Old 05-11-2021, 10:11 AM   #3 (permalink)
Ronin Samurai - Assassin
 
Rusty's Avatar
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 68
Posts: 34,812
Drives: 2011 Nismo GM 6M
Rep Power: 2684436
Rusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond repute
Talking

After you pass the wires through where Madwi showed. Put some RTV around the hole so that it doesn't leak.
DrBacon likes this.
__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html
Rusty is offline   Reply With Quote
Old 05-18-2021, 10:38 PM   #4 (permalink)
Enthusiast Member
 
Join Date: Nov 2016
Location: Washington
Posts: 285
Drives: 2014 Nismo
Rep Power: 27364
DrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond reputeDrBacon has a reputation beyond repute
Default

So, not directly related to my initial question but if anyone comes across this thread in the future while looking up the dlg-1: If you install the o2 sensors slightly down stream (mine are just after the test pipes, in the Y pipe), the cable from the o2 sensors will not reach the gauge no matter how much of a direct path you try to take, it's off by 1-2 feet. You'll need an extension (not sure one exists). Innovate sells an 18foot cable that will work, you'll just have to hide the excess under the carpet or something I guess.

Last edited by DrBacon; 05-20-2021 at 06:55 PM.
DrBacon is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
[FOR SALE] Innovate A/F gauge gsg740 Parts for sale (Private Classifieds) 0 06-26-2020 12:19 PM
innovate scg-1 arnoldas Forced Induction 4 04-11-2019 03:59 PM
[FOR SALE] Innovate Boost Gauge and Innovate Dual Wideband Kit Tusharp83 Parts for sale (Private Classifieds) 4 02-27-2019 08:18 PM
innovate wideband LC-1 Cell Exterior & Interior 6 08-28-2013 08:49 AM
Innovate djtodd Exterior & Interior 3 12-10-2012 09:42 AM


All times are GMT -5. The time now is 11:15 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2