DIY: ** Rear 20mm stud replacement spacers

radek7633 · 12-11-2011, 09:48 AM

^^ appreciated! yes I do have the viscous diff, so this saves me a bit of time this knowledge =) thanks!

ChrisSlicks · 12-11-2011, 11:29 AM

Quote:

Originally Posted by radek7633

^^ appreciated! yes I do have the viscous diff, so this saves me a bit of time this knowledge =) thanks!

You can do it with the sport model one wheel at a time as well, you just will have more resistance turning the hubs.

happytheman · 12-11-2011, 11:34 AM

Ahh, this is good to know for when I do mine! Thanks Chris!

wheee! · 12-11-2011, 12:56 PM

Quote:

Originally Posted by ChrisSlicks

You can do it with the sport model one wheel at a time as well, you just will have more resistance turning the hubs.

Thanks for the confirmation Chris +1! I wasn't sure if the diff would let it slip or not...

ChrisSlicks · 12-11-2011, 01:48 PM

Quote:

Originally Posted by wheee!

Thanks for the confirmation Chris +1! I wasn't sure if the diff would let it slip or not...

Yep, never a full lock up with the VSLD. It will be easier though if the fluid is warmed up from driving. If you do drive it to warm it up give it a few minutes before you start working to let the brakes cool off so you don't burn yourself on the rotors

MattP725 · 12-11-2011, 04:07 PM

Ditto on the VSLD however make sure you have the parking brake disengaged and the car in neutral... I was attempting to remove rotor with the parking brake still on...

The other thing is that since you are taking the car out of gear and removing the brake you better block the front wheels or jack the entire car at once to avoid rolling.

happytheman · 12-11-2011, 04:52 PM

Otherwise, this will happen! BWAHAHHAHAHA

wheee! · 12-11-2011, 08:18 PM

Anarky · 12-11-2011, 08:57 PM

Thanks for the right up

SiRay6 · 12-31-2011, 01:35 AM

Thanks, did my rears tonight and it was easy with your thread.

I didn't need an impact wrench for the rears but I'm sure I'll need one for the fronts which I'll do tomorrow morning.

I went with Z1 motorsports hub centric spacers.

-Ray

wheee! · 12-31-2011, 07:32 PM

You are most welcome!

ChrisSlicks · 12-31-2011, 09:22 PM

Quote:

Originally Posted by SiRay6

I didn't need an impact wrench for the rears but I'm sure I'll need one for the fronts which I'll do tomorrow morning.

Impact wrench isn't necessary on either end but it does make it a lot quicker. I replaced a set of front studs in the middle of an air field with just hand tools after I had one fail, and it was raining and only 50 degrees

Definitely prefer a warm garage though.

SiRay6 · 01-02-2012, 12:24 AM

Quote:

Originally Posted by ChrisSlicks

Impact wrench isn't necessary on either end but it does make it a lot quicker. I replaced a set of front studs in the middle of an air field with just hand tools after I had one fail, and it was raining and only 50 degrees

Definitely prefer a warm garage though.

Yea, I just learned about that yesterday. My impact wrench was not up to the job so I had to get creative without damaging the studs.

I used lug nuts and a breakbar to hold the hub steady so I could tighten down the new stud. All in all, pretty easy without an impact wrench as long as I sprayed some lubricant on the base of the new stud. I think I did the fronts without impact wrench in about 1 hour and a half or less.

-Ray

wheee! · 01-02-2012, 10:30 AM

Make sure you re-tourque those studs a few times in the next month. I don't like lubricating the studs themselves..... too much risk of them working loose.

SiRay6 · 01-03-2012, 12:41 AM

Quote:

Originally Posted by wheee!

Make sure you re-tourque those studs a few times in the next month. I don't like lubricating the studs themselves..... too much risk of them working loose.

Yea, definitely, I check them often because it is a new install...lubricant shouldn't affect it much...after all it is torqued on constantly so it wouldn't just slide out. If my lugs fall out, then I can see more of a chance the stud would back out, but since I check torque, that won't be a problem.

Thanks for the tip still

-Ray

12-11-2011, 11:34 AM	#153 (permalink)
happytheman A True Z Fanatic Join Date: Apr 2010 Location: Florida Posts: 10,737 Drives: MB 6M Tour/Sport Z34 Rep Power: 1823	Ahh, this is good to know for when I do mine! Thanks Chris! __________________ --Brantly-- *PowderCoating by Mike/Stillen/PWJDM/Shine Auto/NST* GTR/Michelin /Fast Intentions/Evo-R/Mobil 1/Motul/Z1 https://facebook.com/CentralFloridaZClub

12-11-2011, 04:52 PM	#157 (permalink)
happytheman A True Z Fanatic Join Date: Apr 2010 Location: Florida Posts: 10,737 Drives: MB 6M Tour/Sport Z34 Rep Power: 1823	Otherwise, this will happen! BWAHAHHAHAHA Ghostvette likes this. __________________ --Brantly-- *PowderCoating by Mike/Stillen/PWJDM/Shine Auto/NST* GTR/Michelin /Fast Intentions/Evo-R/Mobil 1/Motul/Z1 https://facebook.com/CentralFloridaZClub

12-11-2011, 08:18 PM	#158 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 58 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	__________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-31-2011, 07:32 PM	#161 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 58 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	You are most welcome! __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

01-02-2012, 10:30 AM	#164 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 58 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Make sure you re-tourque those studs a few times in the next month. I don't like lubricating the studs themselves..... too much risk of them working loose. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-11-2011, 09:48 AM	#151 (permalink)
radek7633 Base Member Join Date: Oct 2010 Location: Ontario Posts: 102 Drives: 09 Nissan 370 M6 Sp. Rep Power: 15	^^ appreciated! yes I do have the viscous diff, so this saves me a bit of time this knowledge =) thanks!

12-11-2011, 04:07 PM	#156 (permalink)
MattP725 A True Z Fanatic Join Date: May 2011 Location: Toms River, NJ Posts: 1,904 Drives: 2010 40th Rep Power: 18	Ditto on the VSLD however make sure you have the parking brake disengaged and the car in neutral... I was attempting to remove rotor with the parking brake still on... The other thing is that since you are taking the car out of gear and removing the brake you better block the front wheels or jack the entire car at once to avoid rolling.

12-11-2011, 08:57 PM	#159 (permalink)
Anarky Base Member Join Date: Aug 2010 Location: Salt Lake City Posts: 118 Drives: 2011 370Z MB M6 Rep Power: 15	Thanks for the right up

12-31-2011, 01:35 AM	#160 (permalink)
SiRay6 Base Member Join Date: Nov 2011 Location: Diamond Bar, CA Posts: 63 Drives: 12 370z Gunmetal 6MT Rep Power: 14	Thanks, did my rears tonight and it was easy with your thread. I didn't need an impact wrench for the rears but I'm sure I'll need one for the fronts which I'll do tomorrow morning. I went with Z1 motorsports hub centric spacers. -Ray

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
H&R 20mm Stud-Replacement Front Spacer Install	Alstann	Wheels & Tires	8	03-03-2019 05:39 PM
[WTB] 20mm DRS spacers!! (stud replacement)	ts-c63	Parts for sale (Private Classifieds)	2	03-25-2013 10:47 PM
[FOR SALE] 20mm h&r built in stud spacers	memorylasts	Parts for sale (Private Classifieds)	5	02-27-2012 05:29 PM
LTT H&R 10mm Stud Replacement Spacers for 15mm stud replacement H&R	chuckd05	Parts for sale (Private Classifieds)	5	02-16-2011 05:05 PM
FS: Ichiba V1 Stud Replacement 20mm Wheel Spacers	toxik	Parts for sale (Private Classifieds)	9	01-19-2011 05:11 PM