Noise coming from Endlinks

z34von82 · 07-02-2020, 08:58 PM

Quote:

Originally Posted by Rusty

They do move around some. Everytime I look at mine. They're different. The main thing is that they are allowed to move. You don't want bound up. Where you have one all the way one way, and the other all the way the other way. You want them centered after adjustment and locked.

Could you provide pictures how your sways and end links look? I'm now worried about how mine looks since both sides look different :S and I don't think it is normal so hope you can also answer to this..

Rusty · 07-02-2020, 09:03 PM

Quote:

Originally Posted by z34von82

Could you provide pictures how your sways and end links look? I'm now worried about how mine looks since both sides look different :S and I don't think it is normal so hope you can also answer to this..

In your pictures that you posted.The 1st pic looks fine. The 2nd pic. It's fine too. You can just twist it a little to center both ends up.

z34von82 · 07-02-2020, 10:13 PM

Quote:

Originally Posted by Rusty

In your pictures that you posted.The 1st pic looks fine. The 2nd pic. It's fine too. You can just twist it a little to center both ends up.

Will do

thank you sir!

Rusty · 07-02-2020, 10:14 PM

Quote:

Originally Posted by z34von82

Will do

thank you sir!

ZoomZ · 02-21-2021, 03:28 PM

Aren't the conical aluminum spacer supposed to be on the control arm end?

zz

k67p67 · 02-21-2021, 04:28 PM

The conical aluminum spacers belong on the sway bar end of the endlink.

From SPL site:

ZoomZ · 02-21-2021, 04:50 PM

Quote:

Originally Posted by k67p67

The conical aluminum spacers belong on the sway bar end of the endlink.

From SPL site:

Interesting. 2018 SPL install seems to contradict itself in steps 3 and 4. Looking at your image, seems that the angle at the control arm end is not Perpendicular, and is in fact putting an unwanted twist to rod-end. Would make sense to put spacer there to alleviate that. According to image.

IMG_2084 (1).JPG

02-21-2021, 03:28 PM	#5 (permalink)
ZoomZ Track Member Join Date: Jan 2017 Location: Vancouver, BC Posts: 808 Drives: 17' 370Z Nismo Rep Power: 40657	Aren't the conical aluminum spacer supposed to be on the control arm end? zz Last edited by ZoomZ; 02-21-2021 at 03:32 PM.

02-21-2021, 04:28 PM	#6 (permalink)
k67p67 Enthusiast Member Join Date: Oct 2016 Location: Rancho Cucamonga, CA Posts: 315 Drives: 2017 Nismo Tech 6MT Rep Power: 3938	The conical aluminum spacers belong on the sway bar end of the endlink. From SPL site: ZoomZ likes this. __________________ SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work \| Motordyne \| Powertrix \| Swift \| Michelin \| Takeda \| Hotchkis \| RJM \| Voodoo13 \| SPL \| SPC \| Z1 Motorsports \| ZSpeed \| Morimoto \| Craft Square

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
noise when coming to a stop	Limeybastard	Engine & Drivetrain	8	10-29-2014 05:13 PM
Noise coming from exhaust pipes?	zefaulter	Intake/Exhaust	10	09-18-2014 11:23 PM
Noise coming from Transmission and rear	limited733	Engine & Drivetrain	1	03-04-2014 10:53 AM
High pitched noise coming from speakers	invader19	Audio & Video	11	11-12-2012 05:24 PM
Rattle noise coming from real after ark CBE and NOn T/P installed!!	370zjames	Intake/Exhaust	5	08-31-2011 10:24 PM