Homemade Tire Rack

wheee! · 03-06-2010, 05:42 PM

I built a rack for my tires to be stored on during winter. It turned out really good! I welded together some 1/8" angle iron and painted it black. I drilled some holes and used some chain to support the weight. Bolted it onto the stud in the wall with Lag bolts and, voila! Instant tire rack!

This one shows the small amount of space left between the tire and wall to avoid marking the drywall.

Here is the quick build until I can get a complete DIY up:

You will need:

4 x 4' lengths of 1/8" angle iron (fits sport wheels and tires for width)
2 x 2' lengths of 1/8" angle iron (Vertical setions)
2 x 20" lengths of 1/8" angle iron (extensions from wall)

Approx 5' of chain and 4 chain connectors

2 x 3/8" x 1" bolts with lock nuts

welder and paint

How to:

TOP SECTION

Lay the two vertical wall pieces (2') down first. Place the two horizontal 4' sections on top of these (overlapping) at the top and bottom of the vertical pieces, square up and tack into place.

Drill holes in the top sections for the chain to go thru. Try and be accurate for both sides to make it even.

BOTTOM SECTION

Grind the ends of the 20" pieces that will nestle into the rack so that they can rotate up INTO the vertical section for storage. In other words, round off the square end that will rotate so that it will not interfere with the rotation.

Place the two 20" pieces on the table and lay the 4' sections (that support the tires) over these (overlap). The first piece of angle iron is tacked at 8" from the wall and the second piece is at the end of the 20" section. That leaves a 12" "cup" for the tires to sit in and the tires DO NOT touch the wall. Square them up and tack into place. I made this section SLIGHTLY thinner (width wise) than the top section so it could rotate up and into the top section for storage when not in use. To do this I ground off 1/4 " from one end of the 4' sections on the bottom.

Line up the rounded ends with the top section, clamp into place and drill a hole thru both sections and bolt together at the bottom corner. Ensure you have proper clearance for rotation. Drill holes for chain in corners.

FINISHING

Paint the entire piece to prevent rust and to make it purdy. Add shiny chain with link adapters to top and bottom corner holes, making sure that the bottom assembly is SLIGHTLY tilted toward the wall.

Find the studs in your wall and drill holes thru the angle iron in the appropriate locations and Lag bolt to wall. Ensure assembly is level.

and YOU ARE DONE!

Hope this helps. I built mine in about 4 hours. I know it is not perfect and is far from a commercial item, but it looks good and is very strong and functional. I will redo this as a DIY with photos when time permits.

cheers!

dlmartin81 · 03-06-2010, 06:03 PM

I like that. It looks professionally done. Looks like you even painted it.

tbonesteak · 03-06-2010, 07:55 PM

awesome job!!! looks very nice.

cdawg410 · 03-06-2010, 08:46 PM

gonna need you to wash and dress those wheels soldier!!

Looks excellent, great job! Unfortunately I live in a condo so I'll have to convince my wife to let me build one and hang it above the bed.

Nikon FM · 03-06-2010, 08:57 PM

Quote:

Originally Posted by wheee!

I built a rack for my tires to be stored on during winter. It turned out really good! I welded together some 1/8" angle iron and painted it black. I drilled some holes and used some chain to support the weight. Bolted it onto the stud in the wall with Lag bolts and, voila! Instant tire rack!

Oh I like this! Can you provide dimensions? I'm going to build one too. My garage is a pretty tight squeeze and this idea is great!

schrack150 · 03-06-2010, 09:43 PM

nice....ship or can i pick it up
________
Lovely Wendie99

ZCarMan · 03-07-2010, 05:51 AM

Well done!

spearfish25 · 03-07-2010, 06:28 AM

Looks great. The only thing I would add is a back-board that goes along the wall. You're going to have four tire marks on the dry wall...

3SeventyZ · 03-07-2010, 07:03 AM

nice!

ChrisSlicks · 03-07-2010, 09:21 AM

Looks good! I need one that holds 16 tires/wheels please.

Mike · 03-07-2010, 09:22 AM

great job!

m4a1mustang · 03-07-2010, 09:29 AM

That's really cool, good job. But you should clean off your wheels and tires before you put them up there to make them look nice and purdy.

B1nks · 03-07-2010, 09:51 AM

I'm pleasantly surprised at how well this looks, good job !

wheee! · 03-07-2010, 10:54 AM

Quote:

Originally Posted by cdawg410

gonna need you to wash and dress those wheels soldier!!

Looks excellent, great job! Unfortunately I live in a condo so I'll have to convince my wife to let me build one and hang it above the bed.

OK OK! I was VERY busy that day and had just enough time to hang the rack! The tires and wheels were in plastic bags STRAIGHT from the dealer as I had them install the winter tires there. I had no idea they were so mucky! I noticed it too and I feel a little embarrassed....

Quote:

Originally Posted by spearfish25

Looks great. The only thing I would add is a back-board that goes along the wall. You're going to have four tire marks on the dry wall...

Not at all. The rack is designed with angle iron and the bottom rack is spaced 8" from the back and the front one is 20" from the wall, leaving a perfect hollow for the tires to rest in. There is a approximately 3/4" between the rubber and the wall. NO CONTACT!

Thanks for all the positive feedback! I will post the dimensions/instructions here soon. Got to go to church this morning.....

kdoske · 03-07-2010, 01:51 PM

looks great!

03-06-2010, 05:42 PM	#1 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40181	Homemade Tire Rack I built a rack for my tires to be stored on during winter. It turned out really good! I welded together some 1/8" angle iron and painted it black. I drilled some holes and used some chain to support the weight. Bolted it onto the stud in the wall with Lag bolts and, voila! Instant tire rack! This one shows the small amount of space left between the tire and wall to avoid marking the drywall. Here is the quick build until I can get a complete DIY up: You will need: 4 x 4' lengths of 1/8" angle iron (fits sport wheels and tires for width) 2 x 2' lengths of 1/8" angle iron (Vertical setions) 2 x 20" lengths of 1/8" angle iron (extensions from wall) Approx 5' of chain and 4 chain connectors 2 x 3/8" x 1" bolts with lock nuts welder and paint How to: TOP SECTION Lay the two vertical wall pieces (2') down first. Place the two horizontal 4' sections on top of these (overlapping) at the top and bottom of the vertical pieces, square up and tack into place. Drill holes in the top sections for the chain to go thru. Try and be accurate for both sides to make it even. BOTTOM SECTION Grind the ends of the 20" pieces that will nestle into the rack so that they can rotate up INTO the vertical section for storage. In other words, round off the square end that will rotate so that it will not interfere with the rotation. Place the two 20" pieces on the table and lay the 4' sections (that support the tires) over these (overlap). The first piece of angle iron is tacked at 8" from the wall and the second piece is at the end of the 20" section. That leaves a 12" "cup" for the tires to sit in and the tires DO NOT touch the wall. Square them up and tack into place. I made this section SLIGHTLY thinner (width wise) than the top section so it could rotate up and into the top section for storage when not in use. To do this I ground off 1/4 " from one end of the 4' sections on the bottom. Line up the rounded ends with the top section, clamp into place and drill a hole thru both sections and bolt together at the bottom corner. Ensure you have proper clearance for rotation. Drill holes for chain in corners. FINISHING Paint the entire piece to prevent rust and to make it purdy. Add shiny chain with link adapters to top and bottom corner holes, making sure that the bottom assembly is SLIGHTLY tilted toward the wall. Find the studs in your wall and drill holes thru the angle iron in the appropriate locations and Lag bolt to wall. Ensure assembly is level. and YOU ARE DONE! Hope this helps. I built mine in about 4 hours. I know it is not perfect and is far from a commercial item, but it looks good and is very strong and functional. I will redo this as a DIY with photos when time permits. cheers! JARblue and LAVA like this. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal Last edited by wheee!; 03-25-2010 at 04:59 PM. Reason: added bottom view pics

03-06-2010, 09:43 PM	#6 (permalink)
schrack150 Track Member Join Date: Jan 2010 Location: Wheeling, West Virginia Age: 37 Posts: 590 Drives: 09 370z PW Rep Power: 16	nice....ship or can i pick it up ________ Lovely Wendie99 Last edited by schrack150; 04-11-2011 at 01:20 AM.

03-07-2010, 05:51 AM	#7 (permalink)
ZCarMan A True Z Fanatic Join Date: Jun 2009 Location: MD Posts: 4,488 Drives: 09 Z34, 13 F-150 Rep Power: 25	Well done! __________________ Jon Swift \| SPC \| Stillen \| Motordyne \| AAM \| Cobb \| Hawk \| Volk Racing \| Bridgestone Green Demon Eyes

03-07-2010, 06:28 AM	#8 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1856	Looks great. The only thing I would add is a back-board that goes along the wall. You're going to have four tire marks on the dry wall... __________________ 2013 Cadillac V-Wagon, RIP Z

03-07-2010, 07:03 AM	#9 (permalink)
3SeventyZ Track Member Join Date: Dec 2008 Location: MD/DE Posts: 626 Drives: 350Z, 370Z, SRT8 Rep Power: 475	nice! __________________ 2009 Magnetic Black 370Z Sport 6MT

03-06-2010, 06:03 PM	#2 (permalink)
dlmartin81 Track Member Join Date: Dec 2008 Location: Chalfont, PA Age: 42 Posts: 923 Drives: 09 370Z Rep Power: 607	I like that. It looks professionally done. Looks like you even painted it.

03-06-2010, 07:55 PM	#3 (permalink)
tbonesteak Track Member Join Date: Mar 2009 Location: Socal Posts: 914 Drives: MY09 MB 6MT Rep Power: 375	awesome job!!! looks very nice.

03-06-2010, 08:46 PM	#4 (permalink)
cdawg410 Base Member Join Date: May 2009 Location: alexandria, va Posts: 238 Drives: 2009 370z Rep Power: 15	gonna need you to wash and dress those wheels soldier!! Looks excellent, great job! Unfortunately I live in a condo so I'll have to convince my wife to let me build one and hang it above the bed.

03-07-2010, 09:21 AM	#10 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	Looks good! I need one that holds 16 tires/wheels please. MagmaRed370z likes this.

03-07-2010, 09:22 AM	#11 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	great job! __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

03-07-2010, 09:29 AM	#12 (permalink)
m4a1mustang A True Z Fanatic Join Date: Feb 2009 Location: Northern VA Posts: 55,385 Drives: on two wheels Rep Power: 6962	That's really cool, good job. But you should clean off your wheels and tires before you put them up there to make them look nice and purdy. __________________ - Steve Zs & Coffee - Saturdays at 10AM in Fairfax, VA and Columbia, MD (Click the banner!) LIKE us on Facebook!

03-07-2010, 09:51 AM	#13 (permalink)
B1nks Track Member Join Date: Apr 2009 Location: Houston,Tx Posts: 721 Drives: 2009 370Z Base 6MT Rep Power: 507	I'm pleasantly surprised at how well this looks, good job !

03-07-2010, 01:51 PM	#15 (permalink)
kdoske Track Member Join Date: Jul 2009 Location: Louisiana Posts: 541 Drives: 800whp Unicorn FI Z Rep Power: 16	looks great!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to carry a bicycle? bike rack question	FlashBazbo	Nissan 370Z General Discussions	116	09-17-2014 06:50 PM
Wire ties on steering rack boot?	ferrari_rich	Nissan 370Z General Discussions	6	02-02-2010 07:56 PM
Homemade exhaust....if you can get past the wing, that is	2theextreme	The Lounge (Off Topic)	12	07-22-2009 06:50 AM
Tire Pressure Monitoring System; Do you get details on each tire?	raps101	Wheels & Tires	20	06-29-2009 09:17 AM
Tire Rack Wheel Options	spearfish25	Wheels & Tires	5	05-26-2009 12:13 PM