FS Performance V1 Nismo splitter/undertray

redondoaveb · 01-03-2021, 05:12 PM

Quote:

Originally Posted by Spooler

What is the premium edge trim?

By the way, when I told him that a couple of us were interested, he said he would give us a discount

redondoaveb · 01-03-2021, 05:17 PM

Also, he said if there's anything custom or any changes you want made, he would do them.

Spooler · 01-03-2021, 05:22 PM

Quote:

Originally Posted by redondoaveb

Also, he said if there's anything custom or any changes you want made, he would do them.

I need to see a picture of how it integrates with the inner fender. My intakes and brake cooling ducts run through there and it is close.

redondoaveb · 01-03-2021, 05:34 PM

Quote:

Originally Posted by Spooler

I need to see a picture of how it integrates with the inner fender. My intakes and brake cooling ducts run through there and it is close.

It does have brake duct openings. I don't know if they'll be a benefit to you

Rusty · 01-03-2021, 05:44 PM

After looking at the pictures on their website. I have to give this a

The reasons. It doesn't stick out far enough to be effective. It is angled up in the front increasing lift at speed. It still uses the black plastic piece under the bumper.

redondoaveb · 01-03-2021, 05:50 PM

Quote:

Originally Posted by Rusty

After looking at the pictures on their website. I have to give this a

The reasons. It doesn't stick out far enough to be effective. It is angled up in the front increasing lift at speed. It still uses the black plastic piece under the bumper.

Did you remove your factory splitter?

Rusty · 01-03-2021, 05:59 PM

Quote:

Originally Posted by redondoaveb

Did you remove your factory splitter?

The black piece piece under the very front of the bumper? Yea. I'm using the ZSpeed under tray too.

redondoaveb · 01-03-2021, 06:02 PM

Quote:

Originally Posted by Rusty

The black piece piece under the very front of the bumper? Yea. I'm using the ZSpeed under tray too.

When the guy who's car is in the pictures comes in for the diffuser design, he will confirm it's level and not angled upward.

Spooler · 01-03-2021, 06:49 PM

Quote:

Originally Posted by Rusty

The black piece piece under the very front of the bumper? Yea. I'm using the ZSpeed under tray too.

Yeah, it sucks too. I freaking hate that the middle was not keep flat. Too disruptive to airflow. I am thinking about going back to stock.

Spooler · 01-03-2021, 05:26 PM

Anyway we can use different bolts. Bolt heads hanging down look like chit. Anyway we can use some type of flush mount bolts? I will drag those bolts heads off to a nub. LOL

redondoaveb · 01-03-2021, 05:37 PM

Quote:

Originally Posted by Spooler

Anyway we can use different bolts. Bolt heads hanging down look like chit. Anyway we can use some type of flush mount bolts? I will drag those bolts heads off to a nub. LOL

Check your Instgram messages, I sent you the pdf of their installation instructions with pics

Spooler · 01-03-2021, 07:35 PM

Thing for me is I don't want to buy somethings else that doesn't work as intended. I would rather spend more and have a quality piece that works.

redondoaveb · 01-03-2021, 07:55 PM

Quote:

Originally Posted by Spooler

Thing for me is I don't want to buy somethings else that doesn't work as intended. I would rather spend more and have a quality piece that works.

Without seeing wind tunnel tests, you really won't know without trying it and it could end up being a waste of money. In my case, I definitely want functionality but I'm not going to install one that sticks out 6 inches either. I'd rip that thing off the first time I pull into my carport and it just doesn't make sense for a daily driver. I'm kind of screwed. It looks like you can't have the best of both worlds. I'd have to go with this one (if I get one) and hope it provides some kind of functionality (it does look nice) because I can't/won't put a true track splitter on my daily driver because it wouldn't last a week.

Spooler · 01-03-2021, 08:18 PM

Quote:

Originally Posted by redondoaveb

Without seeing wind tunnel tests, you really won't know without trying it and it could end up being a waste of money. In my case, I definitely want functionality but I'm not going to install one that sticks out 6 inches either. I'd rip that thing off the first time I pull into my carport and it just doesn't make sense for a daily driver. I'm kind of screwed. It looks like you can't have the best of both worlds. I'd have to go with this one (if I get one) and hope it provides some kind of functionality (it does look nice) because I can't/won't put a true track splitter on my daily driver because it wouldn't last a week.

Exactly, I am not putting a 6in long one on my car either. They look stupid and they may or may not work. Plus, I drag mine a good many of places. Putting the car in my trailer would be even worse. Still not sure what I want to do yet.

redondoaveb · 01-03-2021, 08:28 PM

Quote:

Originally Posted by Spooler

Exactly, I am not putting a 6in long one on my car either. They look stupid and they may or may not work. Plus, I drag mine a good many of places. Putting the car in my trailer would be even worse. Still not sure what I want to do yet.

This one is one of the nicer ones I've seen for what it is. Looking at the pics in their pdf, it appears to be pretty good quality. Not sure what I'm going to do either but I just don't see a lot of better options out there. Not for the V1 bumper.

01-03-2021, 05:17 PM	#2 (permalink)
redondoaveb A True Z Fanatic Join Date: Apr 2017 Location: So. Commiefornia Posts: 6,386 Drives: 2014 Nismo Gunmetal Rep Power: 2684376	Also, he said if there's anything custom or any changes you want made, he would do them. Rusty and Hotrodz like this. __________________ Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 750whp/700ft.lbs

01-03-2021, 05:44 PM	#5 (permalink)
Rusty A True Z Fanatic Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 70 Posts: 35,579 Drives: 2011 Nismo GM 6M Rep Power: 2684440	After looking at the pictures on their website. I have to give this a The reasons. It doesn't stick out far enough to be effective. It is angled up in the front increasing lift at speed. It still uses the black plastic piece under the bumper. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

01-03-2021, 07:35 PM	#12 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 14,178 Drives: 2013 Nismo 370z Rep Power: 2684395	Thing for me is I don't want to buy somethings else that doesn't work as intended. I would rather spend more and have a quality piece that works. Rusty and redondoaveb like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Zspeed undertray for 2015+ nismo	OptionZero	Parts for sale (Private Classifieds)	14	07-17-2020 06:52 PM
[WTB] WTB: Nismo 09-14 Lip or undertray	NismoNick	Parts for sale (Private Classifieds)	0	06-07-2017 10:44 PM
[WTB] Nismo metal undertray	Kamillio	Parts for sale (Private Classifieds)	0	12-21-2016 08:03 AM
[WTB] ZSpeed Nismo undertray	ZeNato	Parts for sale (Private Classifieds)	6	10-30-2014 05:21 PM
[WTB] Nismo z speed undertray	kornflake7	Parts for sale (Private Classifieds)	3	09-02-2014 07:38 AM

01-03-2021, 05:26 PM	#10 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 14,178 Drives: 2013 Nismo 370z Rep Power: 2684395	Anyway we can use different bolts. Bolt heads hanging down look like chit. Anyway we can use some type of flush mount bolts? I will drag those bolts heads off to a nub. LOL