:bowrofl:

Um, I'm broke now. :rofl2:

:iagree: :yum: thank you sir.

Well, there was that one time... Oh... Uh... :p

:icon18:

Dude! Stifler's Mom! Milf!

You're working too hard! Time for a break. :bowrofl:

Rape train eh? :icon14:

It's alright, the girls are safe.

And all the men are willing so it's kind of a misnomer. :bowrofl:

I would leave now but it's monsoon raining and there's a broken down bus on the highway I need to drive... no point in leaving just to sit in that crap.

Ah yes, I just remembered what forum I'm on. :rofl2:

Took the car out after relocating the temp sensor away from the oil cooler this morning. Got it up to running temps and then pulled some data logs for UpRev to dial in the tune again. It was a beautiful sunny day today too! Perfect day for a cruise....

Well, that's what I keep telling myself! :ughdance:

Ha. Me too. I am going to be 52 this year and I am in the "My mind says YES and my body says MAYBE" mode.

Ok, this isn't exactly matching up. Any advice?

Sent from my PC36100 using Tapatalk 2

work it

You have to remove the machined aluminum piece on the Z1 tube. Not sure why they included those :confused:

Seriously? This would have been helpful to know. Thanks!

Sent from my PC36100 using Tapatalk 2

Np, glad I could help :tup:

A few other things that made the install smoother for me...
I removed the strut bar. Unless you want to be in the garage cussing for a few hours, it's worth the time taking this off first.
I trimmed the tubes up 1/4" on the airbox side. Again, same thing as strut bar.
I also unbolted the airboxes. This made it easier to maneuver the tube onto the throttle body, once connected.
It's also easier with two people.

Strut bar was removed, working with a friend to finish it. Taking a break right now.

Woman working on sports car :yum:

Done! I think.
Questions: Should I be feeling air from the spot where my hand is?
Does that other part im holding get removed for good?
Sorry for the bad picture, flash sucks.
Also, need to now figure out how to get this broken bolt out and replaced.
Sent from my Xoom using Tapatalk 2

+1

Not sure about the air bit, but it doesn't necessarily surprise me.

That's a resonator, and yes..you're done with it.

D'oh on the broken bolt! :facepalm:

Sure does look tasty! :yum: What's your immediate take?

Oh, did you do it yourself?

Oh yeah..Nice Hand! You should be a hand model!

Haven't taken it out for a spin yet. I wanted to check in and make sure the air issue was normal.

I did it with the help of a friend. He did most of the disassembling, I fitted the tubes, we both reassembled.

I should be a hand model! Lol

Check my :ninja3:

Make sure your airbox is seated properly. There's a rubber/foam gasket in the front there where the inlet is that feeds air to the airbox. I had to readjust mine so the gasket had a good seal going to the front of the airbox.

It's too dark out now. I'll have to see if he can help me again. I didn't disconnect the sensors but was able to pull up the boxes and move around a bit, could have sworn we had that side lined up though.

What happens if i don't fix it?

Just tossed on my 20mm powertrix spacers in the front to even out with 25mm in the back.

Sent from my SAMSUNG-SGH-I777 using Tapatalk 2

Looks great Tibal. :)

Is that stock ride height?

:iagree:

Thank you very much! :D

I'm dropped on H+Rs. The angle and zoom is altering the image a bit I noticed. If you look at my sig pic you can see it more clearly.

Sent from my SAMSUNG-SGH-I777 using Tapatalk 2

If there's a way to get more air flow, then it's worth your while to fix it. It's not going to hurt anything though until you do.

:( I really am not looking forward to removing that thing again. Blah!

new mods for today
 

put in my lower rear control arm with a -3 camber re painted my strut bar and engine cover bought new tires and mounted them on got 2 hotchkis sway bars and installed it, bought new cold air intakes by AEM because i got some off brand intakes and got pulled over and got a ticket for my intakes not having a carb sticker... ******* cop... bought the front camber arms now just waiting for intakes and front camber arm...

Wished I could of washed my Z today but alas, miami's weather did not agree with that. Will be cleaning/detailing her over the weekend.

:worthless:

I'm just sayin'!:tup:

Am I the only one doing this? Lol

:tup:

Yes.

Whoops, wrong room!

:wtf2:

I got challenged by a Juke, of all things, heading back from UCD tonight. Wait, I just looked at the picture I snapped with my Droid. That's Mrs. onzedge, that's our Juke. Oops.

You have -3 after rear camber arms???

Finally got exhaust yay!!! M7 Japan... :driving: