Front bumper splintering? + Wheel well destroyed itself

gnznroses · 04-02-2021, 04:37 PM

Ahh, to get the holes to line up I have to lift up hard, and now I see why -- on both sides of the car there's also a clip missing on top, closer to the shocks. These plastic clips are so garbage

JARblue · 04-03-2021, 07:58 AM

It's not the liner that gets warped. I've certainly never had any issues in the Texas heat. But the heat does get to the clips and they get brittle and break easily. Typically they'll hold together until you remove them at which point they'll break, but sometimes they'll just break on their own from vibration. I replace clips all the time; I rarely am able to reuse clips I remove but even when I can I go ahead and replace them with new ones. I'm guessing I have probably replaced every clip for the fender liners at least 4-5 times over the life of the car; going on about 15 replacements of those three clips in the middle of the undershroud.

Ghostvette · 04-13-2021, 01:43 PM

Quote:

Originally Posted by JARblue

It's not the liner that gets warped. I've certainly never had any issues in the Texas heat. But the heat does get to the clips and they get brittle and break easily. Typically they'll hold together until you remove them at which point they'll break, but sometimes they'll just break on their own from vibration. I replace clips all the time; I rarely am able to reuse clips I remove but even when I can I go ahead and replace them with new ones. I'm guessing I have probably replaced every clip for the fender liners at least 4-5 times over the life of the car; going on about 15 replacements of those three clips in the middle of the undershroud.

Like JAR said:

You can get a bag of these clips off of Amazon. Start with a Google search for Courtesy Nissan in Texas, look through the pictures to find the clips, copy down the Nissan part number, then Google the part number. You should be able to find them on Amazon after that.

Ghostvette · 04-13-2021, 01:51 PM

Quote:

Originally Posted by Ghostvette

Like JAR said:

You can get a bag of these clips off of Amazon. Start with a Google search for Courtesy Nissan in Texas, look through the pictures to find the clips, copy down the Nissan part number, then Google the part number. You should be able to find them on Amazon after that.

Well, I got my last set off of Ebay;

https://www.ebay.com/itm/Engine-Spla...5/151260577894

Nissan PN for the fender well clips: 01553-2DR9A $.38 each.

alcheng · 04-13-2021, 03:45 PM

Quote:

Originally Posted by gnznroses

Took a relatively short road trip, and just before getting home I went to clean the windshield again with wipers/spray, and no fluid came out. Figuring it was empty, got home and started filling the reservoir, only to realize it was puddling on the ground. Found two areas of damage:

1. The black plastic in the wheel well, at the front right, was all shredded up. [PIC] The hose for the wiper fluid runs through here and it was severed. My first thought was I'd run over something, but on closer inspection, I don't think so. This black plastic piece has been kinda loose for about two years, and I'd keep pushing it back into place, but I didn't see any way to fasten it or why exactly it was coming loose. It looks like it came really loose during my drive and touched the wheel, because there's a big section shredded up and kinda melted looking.

2. Along my front bumper there's these lines running horizontal. [PIC] They're either scratches (I dunno what could scratch it in that direction), or the plastic is splintering. I'm thinking it's the latter. I've certainly scraped my front end on low driveways and such, many times over the years, but these are new.

On my drive I did hit a hell of a rough railroad crossing, but that's all I can think of lately.

This is really out of my curiosity, you let it loose for 2 year and have no mechanic/shop to look at it or fix it?

robbieZ208 · 04-13-2021, 11:31 PM

Best link for a front passenger fender liner other than z1 that fits good? Mine ripped off too

Sent from my LM-Q730 using Tapatalk

gnznroses · 04-14-2021, 06:13 AM

Thanks all, I'll buy em from Amazon next time.

I bought mine at Advance. Turns out the fender liner clips and the engine splash guard clips are different, as they sell both, but they both fit.

I got to looking better and there were several missing. Like three on one side. Or maybe not all holes have clips in from the factory

gnznroses · 04-14-2021, 06:15 AM

Quote:

Originally Posted by alcheng

This is really out of my curiosity, you let it loose for 2 year and have no mechanic/shop to look at it or fix it?

Haha, yeahhh, I just thought it wouldn't get worse and that I could get it checked out if it did. Figured it'd be $$$ for something small and inconsequential

I was wrong heh. But only slowly wrong

3.7 ZPA · 04-14-2021, 06:23 AM

I had the same thing happen to the liner on the driver side recently. It's completely shredded, so I ordered new liner from Z1. It was about $55. I also ordered new hardware. I think I can chalk it up to 9 years of NY roads, autox, and general abuse.

Sent from my SM-G991U using Tapatalk

victorofhavoc · 04-14-2021, 06:38 AM

What sucks is when bits of your bumper are ripped off with the liner when it makes contact with the wheel

.

The liner and the clips all kind of work together to hold shape. You can lose a few clips, here and there, but they're all basically needed and cheap. I only have the clips break after they've been reused, so I treat them like disposables. Most people use a flathead to pry them open, but I've found this damages them. There's a special tool for popping them out, but at 6$ for a bag of 50 for the clips, it seems not worth it

04-03-2021, 07:58 AM	#17 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,449 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	It's not the liner that gets warped. I've certainly never had any issues in the Texas heat. But the heat does get to the clips and they get brittle and break easily. Typically they'll hold together until you remove them at which point they'll break, but sometimes they'll just break on their own from vibration. I replace clips all the time; I rarely am able to reuse clips I remove but even when I can I go ahead and replace them with new ones. I'm guessing I have probably replaced every clip for the fender liners at least 4-5 times over the life of the car; going on about 15 replacements of those three clips in the middle of the undershroud. gnznroses likes this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

04-14-2021, 06:23 AM	#24 (permalink)
3.7 ZPA Enthusiast Member Join Date: Sep 2012 Location: Connecticut Posts: 352 Drives: '09 370Z 6MT Rep Power: 12	I had the same thing happen to the liner on the driver side recently. It's completely shredded, so I ordered new liner from Z1. It was about $55. I also ordered new hardware. I think I can chalk it up to 9 years of NY roads, autox, and general abuse. Sent from my SM-G991U using Tapatalk __________________ 2009 6MT Touring Sport Z1///Tanabe///ZSpeed///EVO-R///Michelin

04-14-2021, 06:38 AM	#25 (permalink)
victorofhavoc Base Member Join Date: Oct 2011 Location: Kansas City Posts: 229 Drives: 2014 370z Rep Power: 13	What sucks is when bits of your bumper are ripped off with the liner when it makes contact with the wheel . The liner and the clips all kind of work together to hold shape. You can lose a few clips, here and there, but they're all basically needed and cheap. I only have the clips break after they've been reused, so I treat them like disposables. Most people use a flathead to pry them open, but I've found this damages them. There's a special tool for popping them out, but at 6$ for a bag of 50 for the clips, it seems not worth it __________________ Had a 2010 WRX- boy was it quick in a straight line, got a 2014 Z- man is she grippy in the corners-- then left the Z and later got a GTI, now back in an 09 racecar Z!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] 09-14 FRONT BUMPER DIFFUSER NISMO!/ UNDERTRAY / Wheel well protectors	Tomzed	Parts for sale (Private Classifieds)	0	06-30-2018 12:09 AM
WTB: Steering wheel with Airbag, Aftermarket Front bumper,	berrydingle	Wanted	0	06-09-2016 09:43 AM
[WTB] Nismo front bumper assy, steering wheel airbag, windshield reservoir	11nism0	Parts for sale (Private Classifieds)	0	11-16-2015 03:23 PM
[WTB] 2014 PW Nismo Front Bumper and Passenger Side Wheel Lining	Soysauce23	Parts for sale (Private Classifieds)	2	03-24-2015 01:44 PM
[WTB] WTB Amuse Front Bumper, Volks Wheel Red, Stock Navi	tnguyen7787	Parts for sale (Private Classifieds)	36	12-22-2014 09:12 PM

04-02-2021, 04:37 PM	#16 (permalink)
gnznroses Base Member Join Date: Feb 2011 Location: Texas Posts: 51 Drives: '11 Sprt/Trng Loaded Rep Power: 14	Ahh, to get the holes to line up I have to lift up hard, and now I see why -- on both sides of the car there's also a clip missing on top, closer to the shocks. These plastic clips are so garbage

04-13-2021, 11:31 PM	#21 (permalink)
robbieZ208 Base Member Join Date: Sep 2020 Location: idaho Posts: 19 Drives: 09 nissan 370z bl m6 Rep Power: 4	Best link for a front passenger fender liner other than z1 that fits good? Mine ripped off too Sent from my LM-Q730 using Tapatalk

04-14-2021, 06:13 AM	#22 (permalink)
gnznroses Base Member Join Date: Feb 2011 Location: Texas Posts: 51 Drives: '11 Sprt/Trng Loaded Rep Power: 14	Thanks all, I'll buy em from Amazon next time. I bought mine at Advance. Turns out the fender liner clips and the engine splash guard clips are different, as they sell both, but they both fit. I got to looking better and there were several missing. Like three on one side. Or maybe not all holes have clips in from the factory