What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

redondoaveb · 04-28-2020, 06:02 PM

Quote:

Originally Posted by TheFLiP

Found it and ordered. Thanks fellas!

Sent from my SM-G975U using Tapatalk

You're welcome

TheFLiP · 05-14-2020, 12:12 AM

Quote:

Originally Posted by redondoaveb

You're welcome

How did you end up wiring the LED for the switch? I get that I can just use the Normally Closed and Common leads on the switch and it will work without the LED halo.

I'm just cautious to fry the yaw sensor by introducing a current improperly. Thanks!

redondoaveb · 05-14-2020, 03:57 PM

Quote:

Originally Posted by TheFLiP

How did you end up wiring the LED for the switch? I get that I can just use the Normally Closed and Common leads on the switch and it will work without the LED halo.

I'm just cautious to fry the yaw sensor by introducing a current improperly. Thanks!

Just saw this, here's how to wire it

Plug wires:

Black- Ground (there is a black ground wire going to the sensor, but could just be attached to chassis ground)
Green wire- 12 volt side of green sensor wire.
Red/Blue- Twist together but don't attach to anything.
Yellow- Other side of green sensor wire (sensor itself).

TheFLiP · 05-14-2020, 04:09 PM

Quote:

Originally Posted by redondoaveb

Just saw this, here's how to wire it

Plug wires:

Black- Ground (there is a black ground wire going to the sensor, but could just be attached to chassis ground)
Green wire- 12 volt side of green sensor wire.
Red/Blue- Twist together but don't attach to anything.
Yellow- Other side of green sensor wire (sensor itself).

Right on. It's what I figured after digging through the forum a few more hours. The 2012 manual doesn't give the wire color code of the Yaw Sensor

Thanks, man

Sent from my SM-G975U using Tapatalk

redondoaveb · 05-14-2020, 04:28 PM

Quote:

Originally Posted by TheFLiP

Right on. It's what I figured after digging through the forum a few more hours. The 2012 manual doesn't give the wire color code of the Yaw Sensor

Thanks, man

Sent from my SM-G975U using Tapatalk

You're welcome. I actually double checked the wiring with a multimeter to verify the yaw sensor wire and ground.

ABUNAI NISMO · 05-15-2020, 08:43 PM

Installed the Hotchkis rear sway bar today. This bar is adjustable. The hole on the very end is for the stiffest setting. The 3rd hole farthest from the end of the bar is for the softest. I used the middle hole! I also installed the Bell Raceworks differential brace too! I might as well have since I was down there anyhow!

The build is coming along. Slow but sure! I hope to 50% complete by the end of 2020!

WISHLIST

19X9.5
19X10.5 OMARI SPEC LMGT4 (gloss or satin black no preference)

alcheng · 05-16-2020, 02:24 PM

Quote:

Originally Posted by ABUNAI NISMO

Installed the Hotchkis rear sway bar today. This bar is adjustable. The hole on the very end is for the stiffest setting. The 3rd hole farthest from the end of the bar is for the softest. I used the middle hole! I also installed the Bell Raceworks differential brace too! I might as well have since I was down there anyhow!

The build is coming along. Slow but sure! I hope to 50% complete by the end of 2020!

WISHLIST

19X9.5
19X10.5 OMARI SPEC LMGT4 (gloss or satin black no preference)

question: how much downforce or hp do you gain with this Taco Mod..??

I am interested....

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[MAZOC] Official "Off-Topic" Discussion Thread	m4a1mustang	MAZOC	6670	09-06-2018 07:21 PM
What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10007	06-08-2017 09:48 AM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 08:57 AM
What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)	AK370Z	Nissan 370Z General Discussions	10148	06-19-2014 08:20 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 11:21 AM