Missing under piece to bumper/front lip?

Rusty · 04-04-2012, 11:33 PM

Joe, you still going to make one with the brake ducts?

Joe@ZSpeed · 04-05-2012, 06:38 AM

Quote:

Originally Posted by Rusty

Joe, you still going to make one with the brake ducts?

Rusty, It will be awhile, I need to catch up on some other things

Fuct, These are limited pieces. We'll see how it goes whether we make more or not.

Joe@ZSpeed · 04-05-2012, 10:33 PM

Powder Coated Black have arrived! (Very Limited QTY's)

Rusty · 04-05-2012, 10:53 PM

Quote:

Originally Posted by Rusty

Joe, you still going to make one with the brake ducts?

Quote:

Originally Posted by Joe@ZSpeed

Rusty, It will be awhile, I need to catch up on some other things

Fuct, These are limited pieces. We'll see how it goes whether we make more or not.

I'll hold off for awhile on doing anything (buying) until you decide what you want to do. OK?

_ace_ · 04-21-2012, 04:55 PM

A $400ish price is very reasonable for this product--especially considering how small the market is for this part.

I'm an engineer and have been working about 5 years. On a support contract, my company's external billing rate for my labor is $120/hour, so 3 months of my (full) time on a contract would cost just over $60k. ZSpeed will have to sell 150+ of these to bring in that much gross revenue. What are there, <5000 nismos out there?

Making parts like this isn't very profitable, but it's really a benefit for our community. Thanks for making it Joe. I don't need one, but if I do in the future I'll be giving you guys a call.

Rusty · 04-21-2012, 05:48 PM

Quote:

Originally Posted by Rusty

Joe, you still going to make one with the brake ducts?

Quote:

Originally Posted by Joe@ZSpeed

Rusty, It will be awhile, I need to catch up on some other things

Fuct, These are limited pieces. We'll see how it goes whether we make more or not.

Quote:

Originally Posted by Rusty

I'll hold off for awhile on doing anything (buying) until you decide what you want to do. OK?

Joe, if you make the one for the brake ducts. Will the center piece be the same. And the outside "wings" would be different with the ducts?

JJ-NISMO · 06-12-2012, 09:10 PM

Are these still available?

If so, I could use a PM with a price quote for the black and silver! I was on the highway a few days ago, heard a loud pop, and looked in my rearview to see the plastic piece flying down the highway.

Thank you Nissan. What a great design. Prior to losing the piece, I had to replace the full set of clips at least three times. The damn air pocket that is built up in that space causes the piece to pop off no matter what you do! Also, when it is off, I get a loud vibration from the entire front air damn vibrating if I go over 70 mph.

Thanks!

Joe@ZSpeed · 06-12-2012, 10:06 PM

Quote:

Originally Posted by JJ-NISMO

Are these still available?

If so, I could use a PM with a price quote for the black and silver! I was on the highway a few days ago, heard a loud pop, and looked in my rearview to see the plastic piece flying down the highway.

Thank you Nissan. What a great design. Prior to losing the piece, I had to replace the full set of clips at least three times. The damn air pocket that is built up in that space causes the piece to pop off no matter what you do! Also, when it is off, I get a loud vibration from the entire front air damn vibrating if I go over 70 mph.

Thanks!

They are both on the web site, Both versions are in stock at this time.
Aluminum under panels

2011 Nismo#91 · 06-17-2012, 08:16 AM

Well #2, replaced one already, just came off on the highway today. At least I can replaced them under warranty.

fuct · 06-18-2012, 09:07 AM

Quote:

Originally Posted by 2011 Nismo#91

Well #2, replaced one already, just came off on the highway today. At least I can replaced them under warranty.

G Fo12ce · 11-02-2013, 12:56 PM

I lost that stupid cover and now that I've lowered the car it seems to increase the problem where the under pan vibrates making a noise at freeway speeds.

That panel covers a recess I see is built into the ZSpeed pan as well, only the ZS one doesn't have a cover like stock. How does this effect the aero? Is anyone with a Nismo ZS version getting vibrations? Is that fact that the ZS pan is stiff preventing vibration but not providing the same aero? Just questions.

Rusty · 11-02-2013, 01:14 PM

This is what I did to stop the vibration from the under tray. This will work with the stock tray too.

Fix for the rattling front under tray.

G Fo12ce · 11-07-2013, 01:05 PM

2 things. First, In addition to the missing cover I was missing the 3 clips underneath that cover that hold the center of the belly pan to the car. I replaced those and now the rattle is gone. Rusty's and his guide above are a correct fix.

Second, I was contemplating which way to go, replace the stock panel which I was told is $200, or go with the Z Speed diffuser/pan at $399. I'd have a hard time paying $200 for a panel I'll likely loose again so just to confirm I asked the parts guy to confirm the price while I was getting the clips. He said it's $167 (could be the difference in dealer parts dept pricing) and he said oh, it's been superseded to a new number...

"I'm say oh ya, do you know what's different"? He said "it looks like it now includes 5 nuts and bolts".

When I got under my car to pop in the 3 clips, I noticed there are 5 holes in the pan right in front of the holes for the clips that hold the missing cover to the pan. I bet Nissan is aware of this issue and made the cover longer to also bolt on and prevent it from flying off. If I decide to go this way I'll post the result.

Also this is just my opinion but if the stock belly pan has a cover for better air flow and to prevent vibration from pulling the clips out, I think the ZS diffuser should have a cover there also since they are claiming to have better airflow. It would have been easy too as there looks to be rivets there. They could have used bolts and had a simple flat piece cover the hole like factory

chops · 11-07-2013, 04:12 PM

Quote:

Originally Posted by G Fo12ce

2 things. First, In addition to the missing cover I was missing the 3 clips underneath that cover that hold the center of the belly pan to the car. I replaced those and now the rattle is gone. Rusty's and his guide above are a correct fix.

Second, I was contemplating which way to go, replace the stock panel which I was told is $200, or go with the Z Speed diffuser/pan at $399. I'd have a hard time paying $200 for a panel I'll likely loose again so just to confirm I asked the parts guy to confirm the price while I was getting the clips. He said it's $167 (could be the difference in dealer parts dept pricing) and he said oh, it's been superseded to a new number...

"I'm say oh ya, do you know what's different"? He said "it looks like it now includes 5 nuts and bolts".

When I got under my car to pop in the 3 clips, I noticed there are 5 holes in the pan right in front of the holes for the clips that hold the missing cover to the pan. I bet Nissan is aware of this issue and made the cover longer to also bolt on and prevent it from flying off. If I decide to go this way I'll post the result.

Also this is just my opinion but if the stock belly pan has a cover for better air flow and to prevent vibration from pulling the clips out, I think the ZS diffuser should have a cover there also since they are claiming to have better airflow. It would have been easy too as there looks to be rivets there. They could have used bolts and had a simple flat piece cover the hole like factory

i replaced the plastic cover for about 10bucks locally. if you have a plastic shop locally, just use these dimensions:

- 34.5" x 5.85" with 1/2" rounded corners.

like i said, cost me less than 10bucks to have it custom cut in 1/16" ABS plastic with the rounded corners and everything. all i had to do was remove the entire splash shield and drill holes.

04-04-2012, 11:33 PM	#76 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,544 Drives: 2011 Nismo GM 6M Rep Power: 2684439	Joe, you still going to make one with the brake ducts? __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

04-05-2012, 10:33 PM	#78 (permalink)
Joe@ZSpeed A True Z Fanatic Join Date: Mar 2011 Location: Ohio Posts: 1,304 Drives: Nissan Rep Power: 343000	Powder Coated Black have arrived! (Very Limited QTY's) __________________ http://photos.zspeedperformance.com/...ardsize=468x60 Phone *937-506-7224* E-Mail Sales@Zspeed.com www.ZSPEED.com

04-21-2012, 04:55 PM	#80 (permalink)
_ace_ Base Member Join Date: May 2011 Location: USA Posts: 140 Drives: 370Z Rep Power: 15	A $400ish price is very reasonable for this product--especially considering how small the market is for this part. I'm an engineer and have been working about 5 years. On a support contract, my company's external billing rate for my labor is $120/hour, so 3 months of my (full) time on a contract would cost just over $60k. ZSpeed will have to sell 150+ of these to bring in that much gross revenue. What are there, <5000 nismos out there? Making parts like this isn't very profitable, but it's really a benefit for our community. Thanks for making it Joe. I don't need one, but if I do in the future I'll be giving you guys a call. Last edited by _ace_; 04-21-2012 at 05:09 PM.

11-02-2013, 12:56 PM	#86 (permalink)
G Fo12ce Premium Member Join Date: Nov 2009 Location: Socal Posts: 996 Drives: Sold! Rep Power: 52	I lost that stupid cover and now that I've lowered the car it seems to increase the problem where the under pan vibrates making a noise at freeway speeds. That panel covers a recess I see is built into the ZSpeed pan as well, only the ZS one doesn't have a cover like stock. How does this effect the aero? Is anyone with a Nismo ZS version getting vibrations? Is that fact that the ZS pan is stiff preventing vibration but not providing the same aero? Just questions. __________________ Nismo Suspension: New Owners Check Here!

11-02-2013, 01:14 PM	#87 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,544 Drives: 2011 Nismo GM 6M Rep Power: 2684439	This is what I did to stop the vibration from the under tray. This will work with the stock tray too. Fix for the rattling front under tray. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

06-12-2012, 09:10 PM	#82 (permalink)
JJ-NISMO Enthusiast Member Join Date: Feb 2010 Location: SoCal Posts: 276 Drives: 09 NISMO 370Z PG Rep Power: 243	Are these still available? If so, I could use a PM with a price quote for the black and silver! I was on the highway a few days ago, heard a loud pop, and looked in my rearview to see the plastic piece flying down the highway. Thank you Nissan. What a great design. Prior to losing the piece, I had to replace the full set of clips at least three times. The damn air pocket that is built up in that space causes the piece to pop off no matter what you do! Also, when it is off, I get a loud vibration from the entire front air damn vibrating if I go over 70 mph. Thanks!

06-17-2012, 08:16 AM	#84 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,413 Drives: slowly Rep Power: 40570	Well #2, replaced one already, just came off on the highway today. At least I can replaced them under warranty.

11-07-2013, 01:05 PM	#88 (permalink)
G Fo12ce Premium Member Join Date: Nov 2009 Location: Socal Posts: 996 Drives: Sold! Rep Power: 52	2 things. First, In addition to the missing cover I was missing the 3 clips underneath that cover that hold the center of the belly pan to the car. I replaced those and now the rattle is gone. Rusty's and his guide above are a correct fix. Second, I was contemplating which way to go, replace the stock panel which I was told is $200, or go with the Z Speed diffuser/pan at $399. I'd have a hard time paying $200 for a panel I'll likely loose again so just to confirm I asked the parts guy to confirm the price while I was getting the clips. He said it's $167 (could be the difference in dealer parts dept pricing) and he said oh, it's been superseded to a new number... "I'm say oh ya, do you know what's different"? He said "it looks like it now includes 5 nuts and bolts". When I got under my car to pop in the 3 clips, I noticed there are 5 holes in the pan right in front of the holes for the clips that hold the missing cover to the pan. I bet Nissan is aware of this issue and made the cover longer to also bolt on and prevent it from flying off. If I decide to go this way I'll post the result. Also this is just my opinion but if the stock belly pan has a cover for better air flow and to prevent vibration from pulling the clips out, I think the ZS diffuser should have a cover there also since they are claiming to have better airflow. It would have been easy too as there looks to be rivets there. They could have used bolts and had a simple flat piece cover the hole like factory fuct and Rusty like this. __________________ Nismo Suspension: New Owners Check Here! Last edited by G Fo12ce; 11-07-2013 at 01:40 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
need help with missing/broken body piece	Pharmacist	Exterior & Interior	14	10-30-2011 09:51 AM
[FOR SALE] Evo-R CF Diffuser & Front Upper Bumper Piece	AllForTheCash	Parts for sale (Private Classifieds)	11	05-24-2011 03:59 PM
Anyone ever get stopped for missing front plate?	darrinps	Nissan 370Z General Discussions	48	07-01-2010 03:02 PM
Missing front spoiler	Lemers	Exterior & Interior	13	04-01-2010 11:26 PM