TBatt

TBatt Wrote :
Last night I found the problem. A connector was not fully seated on the transmission harness that has the hookups for the O2 sensors. There is a single wire connector that goes up near the starter motor that was not seated all of the way. When it was fixed the car started up.
--------------------
Sorry to bug you 6 years after you posted this - but i have having the same trouble (No recent work done to the car)
I checked the switch with an ohm meter and checked the fuse and the only relay i could find in the IPDM.

The wire you referred to .... where did it come from / Go to?
Thanks Tons for any help you could offer.
Dylan

PM’d you !

Crazy enough I'm in Huntsville and have been looking for a new (to me) car. I had test drove a Nismo up at Jerry Damson but it sold before I got the go ahead from my wife. I was wondering if you where available next week to meet up so that I can check out the 370. I'm Montgomery this weekend but will be back in Huntsville on Monday.

-Edward

Sorry for the slow response but I've been crazy busy at work.

Send via PayPal. My account is tbatt@knology.net

Sounds good where do I send the payment and shipping info too?

The complete kit, with shipping in the US is $175.

Hi ,
How much do you charge for your stillen idler pulley and hd belt upgrade ?

Yes, but i don't have them with me at the moment, they are at my office.

Nice car- Roll Tide ('15)!

Can you share your offsets?

I'm thinking of this as the next phase in my life. After battling with throat cancer the past year I need this (the GTR)!

I'm thinking of this as the next phase in my life. After battling with throat cancer the past year I need this (the GTR)!

Would you be interested in sharing your design file or at least an STL of the design? I have a spool of carbon fiber nylon that I would like to make the part with.

If you change the stock pulley ratio to increase boost you will likely start having belt slip but I have a cure for that. The Stillen belt drive system has a problem in that the belt wrap is very...

If you change the stock pulley ratio to increase boost you will likely start having belt slip but I have a cure for that. The Stillen belt drive system has a problem in that the belt wrap is very...

Have you thought of using a spring inside the silicone tube? It works great with radiator hoses to keep them from collapsing.

Have you thought of using a spring inside the silicone tube? It works great with radiator hoses to keep them from collapsing.

Sorry but you are confused by the two drive belts. My kit goes on the serpentine belt that is driven by the crankshaft pulley. That is why I include a longer belt. The other belt that connects to...

I had a rat chew up my wiring to the left front turn signal. Cost me $200 at the dealer. I put out rat poison and the little bast*rd got in my wife's car and died in the cabin air intake. Another...

Not so much arguing as it is discussing. The end result of both is more power but a different way to get there and a different driving experience. A factory turbo car these days is pretty well...

I've been running the Stillen/TopZ system for several years now and about 8K miles problem free. Here is what I have observed: My SC is setup with the 9psi pulley on the SC. At ~3000 rpm the SC is...

Yes, my install was the first as a clean install. All of the others up to that point were replacing the water system with the A2A. Also, Aaron was just getting into production and that always has...

Not so much arguing as it is discussing. The end result of both is more power but a different way to get there and a different driving experience. A factory turbo car these days is pretty well...

I got to drive the first generation 930 turbo and that car was a hoot! The owner told me that as soon as the tach hits 4000 rpm, shift. I still would hit the rev limiter. The time it took the engine...

Not so much arguing as it is discussing. The end result of both is more power but a different way to get there and a different driving experience. A factory turbo car these days is pretty well...