TBatt

TBatt Wrote :
Last night I found the problem. A connector was not fully seated on the transmission harness that has the hookups for the O2 sensors. There is a single wire connector that goes up near the starter motor that was not seated all of the way. When it was fixed the car started up.
--------------------
Sorry to bug you 6 years after you posted this - but i have having the same trouble (No recent work done to the car)
I checked the switch with an ohm meter and checked the fuse and the only relay i could find in the IPDM.

The wire you referred to .... where did it come from / Go to?
Thanks Tons for any help you could offer.
Dylan

PM’d you !

Crazy enough I'm in Huntsville and have been looking for a new (to me) car. I had test drove a Nismo up at Jerry Damson but it sold before I got the go ahead from my wife. I was wondering if you where available next week to meet up so that I can check out the 370. I'm Montgomery this weekend but will be back in Huntsville on Monday.

-Edward

Sorry for the slow response but I've been crazy busy at work.

Send via PayPal. My account is tbatt@knology.net

Sounds good where do I send the payment and shipping info too?

The complete kit, with shipping in the US is $175.

Hi ,
How much do you charge for your stillen idler pulley and hd belt upgrade ?

Yes, but i don't have them with me at the moment, they are at my office.

Nice car- Roll Tide ('15)!

Can you share your offsets?

That is the best way to verify the correct oil level. Drain and install a full bottle.

You can limp the car around but driving isn't going to be fun with the Stillen tune. Mine ran absolutely terrible until I got my base tune from Seb and then, OH WOW! Vacuum will be lower because...

The silicone coupler coming out of the intercooler looks to be partially collapsed. I remember it being a bit of a pain to get right. I would take it back off and spray the joints with windex and...

Don't be alarmed at the rattling sound of the SC. It is normal for it to sound like it has marbles in it. Really! The gear drive has backlash by design and when the engine idles the SC has no load on...

The silicone coupler coming out of the intercooler looks to be partially collapsed. I remember it being a bit of a pain to get right. I would take it back off and spray the joints with windex and...

The silicone coupler coming out of the intercooler looks to be partially collapsed. I remember it being a bit of a pain to get right. I would take it back off and spray the joints with windex and...

Still loving my QuickJack 3500. Takes up almost no storage space. The lifts are leaned against the wall and the pump & hose box keeps them from sliding out. The lifts have wheels on them so you don't...

Manifold vacuum is what opens the BOV. If the throttles are closed (or barely open) the manifold vacuum goes up and that is what pulls the BOV open. So, at idle it should be open as well as steady...

If i remember correctly when I was chasing a fuel pump problem, when you turn the ignition on the pump will run a couple of seconds and then shutoff. It will not run again until the engine turns...

Just got off the phone with FI and will be going with resonated Test Pipes and the Mil-Spec Cats installed in the front pipes. 6-8 week lead time though........

It may just be me, but the fuel pump part of my install was the hardest part! You are down hill the rest of the way! Take your time and double check everything! Use WINDEX to install the...

In case you haven't run wires yet from the dash to the engine compartment, on the passenger side of the engine compartment is a big rubber seal where the wiring harness passes through. That is where...

AEM FailSafe AFR/Boost gauge. The sensor is on the gauge itself so you have to run a very small hose to the intake manifold and tee it with the BOV hose.

In case you haven't run wires yet from the dash to the engine compartment, on the passenger side of the engine compartment is a big rubber seal where the wiring harness passes through. That is where...

For mounting gauges in a Z, Galeforce is who you need to check into. Fantastic workmanship. http://www.the370z.com/exterior-interior/64959-custom-pillar-gauge-pod-lots-pictures.html