synolimit

Hi, Synolimit. I was reaching out to get some info about porting manifolds, but another member told me you haven't been active on this forum for a while. Seeing the other messages on your profile let's me know you've been inactive for quite some time. I hope everything is OK and you are doing well!

This is your id scott? Just say hi!

there are people trying to get hold of you. Me too eventually when u have a manifold ported since the car is my DD. Hope all is well

i saw on a post that you are running obx long tube headers. You mind giving me a full review on them like whp, torque, and installation etc? i was thinking about getting those myself.

Hey man I have 2 bnib driver side throttle bodies for sale if you're interested. I bought one left and one right but they sent me two driver's side tbs and this was the same week my mother passed and I didn't get around to returning the one in time then found out I didn't need either one in the first place. Make an offer I'll do them for a good price

so you have obx lth did you had to do any mods other than tuning? ex: extending 02 sensor? or something else?

hey，im sheng，i want ask u how GT wing R u use ？

Hello,

would you meet half way from dulles at wheeling WV?
jb

hello,

do you still have them?
josephbalon@gmail.com

Hello. I have been following your thread on ported upper and lower intakes
And t bodies for a while. I have an extra set of throttle chambers and an upper intake plenum for sale if you are interested in them. It looks like you have made good gains on the dyno. I would like to see how they work with test pipes. Let me know if you are interested in the parts. I will be using your throttle body porting on my own vehicle very soon as well. Thanks and good luck at the dyno next time.

This is the hood I would love to have. It's about perfect for removing heat from the radiator. If you could make duct work from the radiator to these vents without letting too much air into the...

Well I think the science behind it is that Heat flows from hot to cold. Heat will draw to cold like a magnet. As colder air running under the car also creates a draft/ suction effect pulling some of...

I'd assume that the air exits underneath the car behind the undertray. There's really nowhere else it could go, right?

Airflow in that direction may interfere with the airflow through the radiator. You want air being pulled out of the engine bay, not going in.

Sure, you could have a good shop make some kind of scoop. I think the one in the pic is too far back. My guess is that the best solution from a function standpoint would be a vent with an...

Still making small bits of progress on various things here and there, mostly waiting to get the cage done before I move on to other post-cage items. A friend and I spent several hours yesterday on...

That's very doable

Here is a pic when I had the 10mm spacer up front. It's not a huge difference with it off to be honest. I have Eibach springs and camber is something like -2.5 front -1.6 rear. Those are an approx...

i love the polished strut bar, but the wire protectors look kinda cheapy.

Great build Sy! Subbed! :tiphat:

Great detailed build. Really like the DIY hood vent.

Check ebay for the cup holder assembly. I have seen one sell for as little as $15. The part number for the blanks is 96916H. Unit price is ~$10 each. MASK-SWITCH HOLE - 350Z (Z33) 2003-2008 ::...

Would never of thought to do this. Too bad I like my DRLs too much =\

nice build dude! I live near westlake, have to check out the car some day!

http://i1109.photobucket.com/albums/h437/chrislspohn/Exterior%20Parts/Rims005_zpsf0556e84.jpg (http://s1109.photobucket.com/user/chrislspohn/media/Exterior%20Parts/Rims005_zpsf0556e84.jpg.html) ...