Ronin06Base Member |
Last Activity: 01-18-2023 03:50 PM
- User Lists
Friends
Showing Friends 1 to 1 of 1
-
- SwissCheese
- Track Member
Likes Given
35 Likes
-
Ronin06 liked post by igota21incher On thread : Holy Understeer!The rear end is just so darn grippy in corners compared to the front, which leads to the front not being able to communicate the turn leading to the 'pushing' feeling. Would increased camber up...Liked On: 07-20-2022, 09:15 AM
Posted On: 07-10-2018, 04:12 PMRonin06 liked post by L33T Z34 On thread : crackcase vent filters??Henry I hacked the POS OEM plastic box to use the pipeing. I then just used the OEM 16mm vac hose, slightly twisted it downward and attached the 5/8" K&N crank case breather. Plugged the OEM...Liked On: 07-19-2022, 03:00 PM
Posted On: 02-29-2012, 06:26 PMRonin06 liked post by xsnapshot On thread : crackcase vent filters??^What? Don't spread miss-information. The ECU does NOT take into account "fuel vapor" as part of the fueling process. And how does "fuel vapor" come from oil? It doesn't. What happens if one engine...Liked On: 07-19-2022, 02:57 PM
Posted On: 02-06-2011, 11:56 AMRonin06 liked post by L33T Z34 On thread : crackcase vent filters??I have two K&N 62-1340 on my Z. No problems.Liked On: 07-19-2022, 02:56 PM
Posted On: 02-01-2011, 06:06 AMRonin06 liked post by synolimit On thread : OBX long tube Headers?Fans boys you mean? Think that sums it up. Welds can crack , I've seen it on all, does that mean everyone's stuff is junk? Who cares about gaskets? They all use the same crap unless you buy...Liked On: 09-10-2021, 01:13 PM
Posted On: 12-04-2015, 03:50 PMRonin06 liked post by BGTV8 On thread : Help me pick my Rotors and pad (Akebono stock replacement) + Motive Bleeder & fluidWhy not use DOT 5.1 ...... I would have thought don't use DOT 5 which is silicone-based and prone to frothing in an ABS system with the predictable outcome. DOT 5.1 is not to be confused with DOT...Liked On: 07-06-2021, 04:36 PM
Posted On: 09-21-2012, 08:14 PMRonin06 liked post by kenchan On thread : Wheel Nut Torque Specs80-85ft/lbs is your target, msbc. :tup:Liked On: 07-05-2020, 01:53 PM
Posted On: 08-15-2013, 08:56 PMRonin06 liked post by ChrisSlicks On thread : 370Z Clutch Line Upgrade - Experiences?Believe it or not RBF600 actually has a higher boiling point both wet and dry vs AP 5.1. AP 5.1 is excellent performance for the money though, so it is a good fluid to use and a fair bit cheaper. ...Liked On: 07-02-2020, 11:55 AM
Posted On: 06-27-2012, 06:56 AMRonin06 liked post by ChrisSlicks On thread : 370Z Clutch Line Upgrade - Experiences?The #1 thing is swapping out the fluid, it doesn't hurt to do the line but high temp fluid plus a little bit of insulation will make 99% of the difference. Put some MOTUL RBF600 in there and bleed...Liked On: 07-02-2020, 11:54 AM
Posted On: 06-26-2012, 03:12 PMRonin06 liked post by ChrisSlicks On thread : DIY: Fix your crappy Parking Brake...make it work!Nice write up. I don't understand why they come so far out of adjustment from the factory. Mine isn't as bad as some but I still have to pull it up further than I should.Liked On: 07-02-2020, 11:18 AM
Posted On: 05-27-2011, 04:59 PMRonin06 liked post by spearfish25 On thread : DIY: Fix your crappy Parking Brake...make it work!Since I got my car two years ago, I've thought my parking brake was horrible. I had to pull the damn thing as hard as I could to even begin to slow the car. It took multiple successive yanks to...Liked On: 07-02-2020, 11:17 AM
Posted On: 05-27-2011, 04:36 PMRonin06 liked post by MarkGideon On thread : jacking points:D But I did go through a few hockey pucks before the lift. ...Liked On: 06-27-2020, 03:34 PM
Posted On: 01-28-2019, 06:35 PMRonin06 liked post by AK370Z On thread : DIY: How to Bleed Your Brake Fluid Using Motive Power Bleeder 0117 (AK370Z)I have been meaning to post this DIY for few weeks now. I did this couple weeks ago. Those of you who go to track regularly, I'm sure you've done this many times. I still decided to post this perhaps...Liked On: 09-30-2018, 06:55 AM
Posted On: 04-09-2013, 11:43 PMRonin06 liked post by djtodd On thread : DIY: Replacing Your Clutch, Pressure Plate, Flywheel, and CSC (Zspeed HD CSC)Hey folks, Here's a DIY on replacing your flywheel, PP, clutch disc, and CSC. I remember looking for a DIY and not seeing one back when I first went through this. So I thought I would try to...Liked On: 07-12-2018, 03:31 PM
Posted On: 09-14-2013, 01:52 AMRonin06 liked post by forza370z On thread : Opinions needed:ZSpeed HD CSC or Z1 Motorsports Slave DeleteThis is a good thread. I was asking this question over here and facebook group a couple weeks ago since I need to replace my CSC asap. But unfortunately didn't get much feed back. But here is what...Liked On: 05-13-2017, 11:41 AM
Posted On: 01-21-2015, 01:32 PM
All times are GMT -5. The time now is 05:30 PM.