Modshack

Hey Modshack. I did my oil cooler install many years ago based on your write-up. It's been working just fine, although sometimes driven hard at the track, temps could still go up high enough to require me to take a break before the session is over. My car is at a shop now and the guy working on it says the cooler should never be installed with the fittings facing down. Is this true?? I'll ask him in more detail when I get there, but over the phone he said it's not right and needs to be corrected so that the fittings face up. I've never heard this before. What do you think??

Just curious where you got the flanges for the fang vent mod, I would like to try duplicating your results but not too sure where to get the materials.

I saw a post you made on a thread where it was discussing short throw shifters. I also saw your custom redline boot you had installed on your Z with a new knob. I ordered an AMS short throw and I have the BLOX torch blue shift ball for it. I emailed them and asked about the two section boot as you have and the factory nissan has. However in an email that he sent back he asked me what circumfrence I need. I would assume it would be the same circumfrence as the shaft that has the threads. Is this what you used?

Thanks for the trouble

hey mod i was wondering if you had anymore of the scanguage II brackets? and also can it measure air fuel ratio?

Thanks for ur help, Modshack!

Hi Modshack, thanks for the help last time! i am buy spacers with my advan RS wheels. What spacers do you recommend? My wheel specs are 19x9 +22 front and 19x10 +25. Also, do u kno the bore of our wheels. I heard it is 66.1. Thanks very much.
Btw, you should check out my album of my new wheels.
Thanks
Kevin

DIY of the day: Login | Facebook

Congrats sir. DIY of the day The370Z Forum | Facebook

thanks so much!

Hey Modshack, I have seen almost all your posts and I really admire your knowledge in intakes! I have a question for you. I am getting K&N drop-ins on my stock intake system. Do you think this $100 is a good investment? Will I be able to feel any difference than stock air filters? The stock filters looks remarkably clean even after 10,000 miles!
Thanks
kevin

Update on the SRP pedals. Machine work done and they're in the mail to me...Should receive tomorrow or Saturday as they're just across the State in Charlotte. More when I do the install! Here...

Lots of us have looked at the block off plates by the fangs and wondered why. They are a perfect high pressure area to tap for some cooling. It's not hard, takes about $75 in parts and a few hours...

Lots of us have looked at the block off plates by the fangs and wondered why. They are a perfect high pressure area to tap for some cooling. It's not hard, takes about $75 in parts and a few hours...

While a few guys have done this, I haven't seen a DIY so here goes. Adding 15mm spacers with extended studs requires jumping through a few hoops.. First, Buy (2) M12 x 1.25 lug nuts (open style)...

Flexibility I'd guess..Most cars use a flex pipe between the engine that moves on its mounts and the airbox that is usually hard mounted to the chassis..

Lots of us have looked at the block off plates by the fangs and wondered why. They are a perfect high pressure area to tap for some cooling. It's not hard, takes about $75 in parts and a few hours...

Just a simple warning....Always remove, or at least loosen, the fill plug FIRST. Nothing worse than having drained your fluids and then not being able to get the new stuff in caust the fill plug is...

Well.....since that was shown I've designed a flip out holder. Pivots out from the cubby and will hold Nav or Phone set-ups. Her it is with my Droid Incredible in an iPhone 3 holder: ...

Lots of us have looked at the block off plates by the fangs and wondered why. They are a perfect high pressure area to tap for some cooling. It's not hard, takes about $75 in parts and a few hours...

While a few guys have done this, I haven't seen a DIY so here goes. Adding 15mm spacers with extended studs requires jumping through a few hoops.. First, Buy (2) M12 x 1.25 lug nuts (open style)...

That might be a little difficult with the routing clearances and plastic/metal in the way, but here are some other ideas that would work for a track setup using the same hoses and flanges and a few...

Lots of us have looked at the block off plates by the fangs and wondered why. They are a perfect high pressure area to tap for some cooling. It's not hard, takes about $75 in parts and a few hours...

For those of us with the standard and sport options, the pedals are nothing to write home about. A little dowdy and a little plain. To upgrade to the Touring aluminum "trimmed" pedals costs almost...

While a few guys have done this, I haven't seen a DIY so here goes. Adding 15mm spacers with extended studs requires jumping through a few hoops.. First, Buy (2) M12 x 1.25 lug nuts (open style)...

http://images51.fotki.com/v1560/photos/5/7305/7658982/IMG_2051-vi.jpg and: http://images9.fotki.com/v449/photos/5/7305/8438315/IMG_2471-vi.jpg