![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() juld0zer
|
Last Activity: 11-07-2017 06:15 AM
- User Lists
Visitor Messages
Showing Visitor Messages 1 to 1 of 1
-
08-09-2021 01:28 PM - permalinkdribble1975Hey bud. I read your fix for the axle click using the Kawasaki nut. Has it still held up? No noise? Any issues with this fix?
Likes Received
107 Likes
-
DIGItonium liked post by juld0zer On thread : HELP! Severe acceleration lagOk, so i finally had some time to do some experiments - because driving around with no brake lights or brake lights constantly on is not cool. In short, i was eventually able to replicate the...Liked On: 06-23-2014, 01:38 PM
Posted On: 06-23-2014, 10:52 AM6spd liked post by juld0zer On thread : FIXED: Rear axle click clunk noiseHey guys, As some of you will know, i've been battling these clicking axles for a while. I have tried: - Lazy fix - basically removing the big nut, pushing the axle in as far as possible and...Liked On: 06-23-2014, 10:25 AM
Posted On: 06-23-2014, 10:21 AMesfourteen liked post by juld0zer On thread : HELP! Severe acceleration lagi'll load the stock map into one of the slots and see how it goea. as for oil level - it's as full as it was when i changed oil 3000km/2 months agoLiked On: 06-12-2014, 05:35 PM
Posted On: 06-12-2014, 05:28 PMJordo! liked post by juld0zer On thread : Oil temps: 335 comparitive observation.Jordo! Good demonstration of how the undertray does not need to be removed for an oil change! I only discovered this at my last oil change & it saves many minutes messing around with the million...Liked On: 06-07-2014, 04:23 PM
Posted On: 06-07-2014, 05:19 AMJordo! liked post by juld0zer On thread : Oil temps: 335 comparitive observation.I've read heaps about the DLC and it's relationship with ester based oils. It must be a Nissan USA thing to mandate ester oil for the earlier model 370z (up until 2010 model iirc). In Australia, you...Liked On: 05-21-2014, 03:02 PM
Posted On: 05-21-2014, 06:19 AMJordo! liked post by juld0zer On thread : Deleting the Crankcase vent?deleting 6 and 14 is a bad idea for NA as you'll get idling issues. look here: http://www.the370z.com/engine-drivetrain/5977-help-please-engine-idle-problem.html even if you disconnected them...Liked On: 03-06-2014, 05:38 PM
Posted On: 03-05-2014, 05:19 PMMandingo liked post by juld0zer On thread : NST Pulley - Installed and Reviewed! (Crank bolt removal tip inside!)I'm onto night #2 of my pulley install. First night was pretty fruitless. Bolt stuck on hard. Tried penetrating lubricant and jolting the starter but i must've chickened out & let go of the clutch...Liked On: 12-06-2013, 11:35 PM
Posted On: 12-04-2013, 09:14 AMFountainhead liked post by juld0zer On thread : Magnetic drain plug for 6MT gearboxHey guys, Just thought I'd share my success with installing a magnetic drain plug into my 6MT gearbox. The plug i used is a Dimple M18 x 1.5 x 12 intended for a Harley, BMW or Mini. Thanks for a...Liked On: 10-14-2013, 09:02 AM
Posted On: 10-13-2013, 10:09 PMfuct liked post by juld0zer On thread : Magnetic drain plug for 6MT gearboxHey guys, Just thought I'd share my success with installing a magnetic drain plug into my 6MT gearbox. The plug i used is a Dimple M18 x 1.5 x 12 intended for a Harley, BMW or Mini. Thanks for a...Liked On: 10-14-2013, 08:49 AM
Posted On: 10-13-2013, 10:09 PMgSwift liked post by juld0zer On thread : Magnetic drain plug for 6MT gearboxHey guys, Just thought I'd share my success with installing a magnetic drain plug into my 6MT gearbox. The plug i used is a Dimple M18 x 1.5 x 12 intended for a Harley, BMW or Mini. Thanks for a...Liked On: 10-13-2013, 10:24 PM
Posted On: 10-13-2013, 10:09 PMwheee! liked post by juld0zer On thread : Intermittent failure to start...my SRM issue turned out to be the Input Speed Sensor on the gearbox. It had some blobs of fine metal particles stuck to it (it's a magnetic flux type device). Cleaned it up and shifting has never...Liked On: 10-09-2013, 09:36 PM
Posted On: 10-09-2013, 05:58 PMSouthArk370Z liked post by juld0zer On thread : Intermittent failure to start...my SRM issue turned out to be the Input Speed Sensor on the gearbox. It had some blobs of fine metal particles stuck to it (it's a magnetic flux type device). Cleaned it up and shifting has never...Liked On: 10-09-2013, 06:23 PM
Posted On: 10-09-2013, 05:58 PMZbrah liked post by juld0zer On thread : Side skirt removal?Here's the album with the images in chronological order: ImageShack Album - 10 images (http://imageshack.us/g/1/10336251/) 1st pic is of the stubby ratcheting screwdriver i used to avoid having...Liked On: 09-30-2013, 12:52 AM
Posted On: 09-30-2013, 12:31 AMDIGItonium liked post by juld0zer On thread : Rear Axle Clunk (Please Report Here!)ok, so the regreasing fixed my clunking. unfortunately for me it wasnt a 35min per side job. getting the axle nut off and applying the grease as per the 350z UK forum was the easiest part. the...Liked On: 09-08-2013, 11:52 PM
Posted On: 09-08-2013, 07:44 AMCronus liked post by juld0zer On thread : DIY: STILLEN G3 IntakesThe ECU will be reset as a result of extended loss of battery power, however it's easier and quicker to just do a pedal dance reset if all you require is an ECU reset.Liked On: 06-26-2013, 10:34 PM
Posted On: 06-26-2013, 07:52 PM
All times are GMT -5. The time now is 10:33 PM.






Likes Received