What are you Teeing off of for your gauge pressure source?

I tapped the front of the intake manifold and have a line running to the BOV. I was thinking of t-ing into that.
I bought a 1/4 x 1/4 x 3/16 T fitting.

That should work. I just wouldn’t recommend teeing off the line that runs to the waste gates if you are running an EBC teed off that line too. I tapped the manifold and ran a dedicated line to the boost gauge.

I thought about doing that but didnt want to pull the manifold off, again. :icon17:

rear of manifold@brake booster connection :tup:

Front where we tapped in the brass fitting.

Madwi's picture dump and crap
 

Don’t think that will work with the Tee he bought. I think that hose is 3/8 or 1/2”.

A lot of people put a manifold in right there for all their needs. Like this:

https://www.on3performance.com/shop/...ibution-block/

I like that.

dang, now I gotta rethink this lol.

That was just a quick search for vacuum blocks. They make better ones so don’t necessarily buy that one. It’s probably a waste now that you’ve tapped for the BOV. Would of been a good solution at the beginning. Unless you have future needs for pressure source, I wouldn’t bother.

I actually havent cut the line yet. :tup: I am searching google now for the blocks.

The company Sasha gets the FMICs from has a pretty good one. Just can’t think of the company name at the moment.

Just went through this whole build. VERY nice! We will need to meet up next summer.

I agree! I cant wait to see that beast of a build you got in the shop! :driving:

CJ motorsports Motor mounts came in today. Will order poly trans mount in near. Who know when they will go in as I dont want to rip everything apart now that it is almost put back together. :icon17:
https://i.imgur.com/dk67zjCl.jpg

Decided to get off my fat *** and get the bumper fitted around the intercooler and FI tow bar. Yep, same bumper from waaaaaaaay back in this thread resurfaces. I had stashed it away when I thought I was going to get rid of the Z.
Had to trim a most of the middle piece away which was made easy with an air powered cutoff wheel. Be sure to wear a good mask and eye protection when cutting!
https://i.imgur.com/d4z5SEPl.jpg

:tup:

Fiberglass dust ain't good for you. :rofl2:

:iagree: :iagree:

I started taping the hood for the tracspec vent install. Its about 6* right now and I cant clean the hood off to lay the rest of tape because everything freezes instantly when sprayed on the hood :icon17:

Thinking of using black mesh as that would blend in well.

You going to put the screen under the hood vents?

You NEED heat in that garage!

I was thinking about it. :tup:

I NEED a money tree like you and Bob have! :icon17:

I have a guy lined up to give me a quote on insulate, drywall and tape/mud this spring.

Insulate and drywall is easy. Tape/float sucks ****.

You got that right. I've done my fair share in this lifetime, Im over it.

Dug this thing out from the shadows. Might take a look at removing the oem spoiler this weekend. Ebay nismo spoiler replica.
https://i.imgur.com/Ik2rZDsm.jpg

Money tree died when I retired. :shakes head: Living off of the investments. :tup:

:iagree::iagree::iagree:

Thermometer out in garage says it is 3*F right now. Temps are suppose to fall this weekend thru mid next week. :icon14:

:wtf2:

:iagree:

Time to put some sox on :tiphat:

I'm going to lite a fire and it I'll burn straight thru the week

A couple things showed up at the house. :tup: *Dont mind the nitrous bottle heater...it is in for sale section though :)
https://i.imgur.com/INsXT8gl.jpg

Rotors are suppose to be delivered today, hopefully UPS doesnt just SAY they attempted delivery when I was home the whole time. :stirthepot:

https://i.imgur.com/dUjLzywl.jpg

Got some whoa to go with the go now. :driving:

I suppose stopping is a good thing too.

Rotors wont be here until Monday according to UPS. :mad:

That blows!

:iagree: Suppose to be decent weather this weekend after freezing our nuts off this past week.

Grabbed a couple mounts for the Hotchkis sway bar.
https://i.imgur.com/oIguWAml.jpg