K&N drop ins are the best

jran76 · 05-10-2011, 10:50 AM

No doubt the Stillen makes good power on the dyno compared to the stock boxes, but is hard to simulate what the factory intakes are designed for on a dyno. They are specifically made to operate more effectively while the car is in motion, and designed to force more air in as speed increases (something a dyno cannot replicate). Even with large fans this is difficult to simulate on a dyno.

With the above said, Stillen is really the only intake that has proven to produce any noticeable gains on the VQ37VHR, so if you are going to drop your cash on an intake, go with Stillen (not a huge Stillen fan, but I will give them some credit). The 4-5 HP you end up with is not worth $500 and hacking up your car to me, but I know it is to some and you can't argue that they don't sound good.

jran76 · 05-10-2011, 11:07 AM

I also find it interesting that in the most high performance version of this engine, (used on the Nismo 380RS) they use the exact same stock air boxes. I think if an intake really performed better a) Nismo would know best, and b) they would be all over it. Also, let me remind you, Nismo makes similar intakes for these engines, and they are no where to be found on the most expensive high performance variant of this motor.....

EDIT: Actually, after looking into this again, it looks like they switched to a cone style intake in a CF "suction" box, but in the stock locations on the 380RS-C, along with a Motec, and new plenum....

wstar · 05-10-2011, 11:19 AM

Quote:

Originally Posted by jran76

No doubt the Stillen makes good power on the dyno compared to the stock boxes, but is hard to simulate what the factory intakes are designed for on a dyno. They are specifically made to operate more effectively while the car is in motion, and designed to force more air in as speed increases (something a dyno cannot replicate). Even with large fans this is difficult to simulate on a dyno.

There's something to be said for that for sure (the general point that the dyno models street/highway airflow poorly). Keep in mind the limits of that effect though. No amount of increased airflow pre-filter (even a 100mph fan right in front of the bumper) is going to cause any sort of forced induction effect.

Bad airflow could result in a lack of available air/pressure at the filters (i.e. maybe your intake placement is so bad that the engine can't draw in the air volume it wants to, because of a low pressure area near the filters at speed). Most intake designs aren't so tragically poorly tested as to suffer from this problem though.

Mostly intake changes are only going to affect a car significantly in one of four basic ways (most of which can be seen on the dyno, to some greater or lesser degree, or can be seen by monitoring intake air temps while driving):

1) Changing the CFMs allowed to flow through the filters. Assuming the intakes/filters are restricting intake flow to a lower CFM than what the engine would otherwise pull, getting rid of some of that restriction will help at high air flow volumes (high rpm).

2) Changing the temperature of the intake air (IAT) (colder is better, and the more you're picking up external air instead of engine bay air, the colder it gets).

3) Changing the available air volume in the intake tubes (between the filter and the intake plenum proper). I don't claim to fully understand the effect of this. it would seem this would improve response to the throttle plates opening up, since you have more available post-filter air to immediately suck in via engine vacuum. On the other hand, if it effectively acts as an extension of plenum volume (does it?) it would actually reduce your throttle response by a bit.

4) Airflow smoothness. Ideally you want laminar flow, no crazy turbulence to hold up the engine's draw of air. Changing the intake configuration could have large positive or negative effects here.

We know, for example, that it's obvious an intake like the Stillen Gen3 wins over the stock setup on items 1 and 2 (CFM and temps). Even if you put K&N drop-ins on your stock airboxes the G3 still wins on CFM, just look at the filter area and it's obvious.

There are ways to get the stock airboxes to beat the G3 on IAT (e.g. intake ducts cut into the top of the bumper that route directly to the stock holes through the radiator core support), but they look a lot more rain-problem-prone than the default G3 setup. For that sort of thing, I'd rather run an L-shaped duct up to the G3s (e.g. Modshack's custom ductwork) which would tend not to push water up into the intake and again lower IAT further.

As far as airflow smoothness goes, the G3 seems to be designed well. Post-MAF tubes that replace the factory crinkly-tubes probably help with that as well.

I think the only real question where people might have doubts after trawling through all the available evidence and design factors is: what exactly are the effects of the greatly-increased intake tube air volume the G3's have between the filters and the throttle bodies? Whatever your take on that issues is though, I don't believe it would be affected by rolling airflow to the bumper. FWIW my G3 setup has great throttle response in neutral. I don't remember detecting any increased throttle lag from that install.

OKC Z · 05-10-2011, 11:39 AM

Aaaamen!! Good sermon.

jran76 · 05-10-2011, 11:53 AM

Just a couple comments because I am too lazy to respond to all of it (and I agree with most of what you are saying)....

Turbulent air is more of an issue at the MAF sensors, or pre-MAF, and I will agree that in general turbulent air is a bad thing (it just has less of an affect once being sucked in under vacuum). The biggest issue (and one that some aftermarket intakes suffer from) is the affect of turbulent air has on readings by the MAF sensor. I do think Stillen's design helps keep turbulent air to a minimum pre-MAF, and one of the primary reasons it performs better than most other aftermarket intakes.

From all the testing I have seen (by 2-3 extremely reputable companies), there is nothing to indicate the stock boxes are in any way restrictive, or cannot provide enough air to the engine. I think the Stillen brings in slightly cooler and more air on the dyno, and that is the big advantage. At speed, I don't think the amount of air the factory boxes can flow is an issue. They are also bringing in a lot of the cooler air the Stillen is going to pull in once the car is in motion.

Also, one last comment on the throttle plates/bodies, according to Mike Kojima (who did a lot of research on the VQ37VHR early on):
"The unique VVEL system completely controls the intake valves opening and closing events.... The command authority of the VVEL system is great enough so controlling valve opening is the primary means of throttling the VQ37VHR’s output, instead of traditional throttle plates.The VQ37VHR does retain twin drive by wire throttles but they mostly stay wide open, the only time they close is on overrun to help provide engine braking and if the engines ECU detects low vacuum in the brake booster reservoir."

Reference (full article): Edit.... The link is blocked, I guess because it is from another site (god forbid should we share relevant information). If anyone really cares about it, I am sure you can search for Mike Kojima's site and find the article I quoted.

jran76 · 05-10-2011, 12:04 PM

One more thing.... I know there are lot of people on here that love their Stillen intakes, and I think that is great. You are very passionate about them, and I know I am not going to change your mind. There is nothing wrong with the Stillen intake. It is a lot better than any other aftermarket intake I have seen or researched. My only point is that the stock air boxes are not a problem compared to some of the other restrictions.

Z eliminator · 05-10-2011, 12:47 PM

My G3 stillen made 20 rwhp over the stock intake. It was my first mod.
baseline stock car 264.. with stillen 284.rwhp SAE.
Mine is a 7 AT. sports
have the dyno charts to back it up.

Z

jran76 · 05-10-2011, 01:00 PM

Quote:

Originally Posted by Z eliminator

My G3 stillen made 20 rwhp over the stock intake. It was my first mod.
baseline stock car 264.. with stillen 284.rwhp SAE.
Mine is a 7 AT. sports
have the dyno charts to back it up.

Z

What did it do to your trap speed? Did you do any before/after races?

Quartermaine · 05-10-2011, 03:09 PM

Quote:

Originally Posted by Z eliminator

My G3 stillen made 20 rwhp over the stock intake. It was my first mod.
baseline stock car 264.. with stillen 284.rwhp SAE.
Mine is a 7 AT. sports
have the dyno charts to back it up.

Z

Can you post the chart? If not, can you let me know what kind of hp and torque it made in the mid range rpm over base?

It is amazing what these CAI can do for Z's engine. On my old 1998 prelude (H22A4), CAI, headers, and exhaust only netted 10hp. What a difference.

Joka4411 · 05-10-2011, 03:14 PM

I am not really in to a lot of the tech stuff about the air intake system, But I do know that my car performs better with the stock intakes, Also thanks for all the positive feed back.

wstar · 05-10-2011, 06:49 PM

Quote:

Originally Posted by jran76

One more thing.... I know there are lot of people on here that love their Stillen intakes, and I think that is great. You are very passionate about them, and I know I am not going to change your mind.

Please don't put me in this camp though. I run the G3 intakes, and I like them, but I'm loyal to no vendor. If I find evidence a mod isn't working out right, it comes off in a heartbeat, although I do try to avoid bashing the vendor about it. I had epic problems with a Stillen exhaust system back in 2009 and I was never satisfied with their customer support on that issue. I ended up eating the cost of the exhaust and throwing it out at a metal recycling place.

wstar · 05-10-2011, 06:53 PM

Quote:

Originally Posted by jran76

The command authority of the VVEL system is great enough so controlling valve opening is the primary means of throttling the VQ37VHR’s output, instead of traditional throttle plates.The VQ37VHR does retain twin drive by wire throttles but they mostly stay wide open, the only time they close is on overrun to help provide engine braking and if the engines ECU detects low vacuum in the brake booster reservoir."

On this point: I remember hearing about this in the past, but I don't think stock ECU actually operates in this manner. I've never run my car with the intakes off to visually verify, but when monitoring throttle position sensors (which means the actual throttle plates on our car, not the accel pedal) via Torque or Cipher, it seems they do progressively open just like the throttle plates of any other car. I imagine Osiris or similar should be able to tune them wide open under accel, but I'm not sure.

flashburn · 05-10-2011, 07:03 PM

Quote:

Originally Posted by wstar

Please don't put me in this camp though. I run the G3 intakes, and I like them, but I'm loyal to no vendor. If I find evidence a mod isn't working out right, it comes off in a heartbeat, although I do try to avoid bashing the vendor about it. I had epic problems with a Stillen exhaust system back in 2009 and I was never satisfied with their customer support on that issue. I ended up eating the cost of the exhaust and throwing it out at a metal recycling place.

Yeah, same here. I don't really like this dude saying basically "you guys are only acting like you got gains because you are loyal to Stillen and you spent a lot of money". The gains are PROVEN, end of story. You "feeling" like stock is better, is just that, a feeling, with no proof what-so-ever to back it up. If there was hard proof that the stock intakes were better than the G3's, I'd rip them off in a heart beat, and I bet that many others here feel the same way.

jran76 · 05-10-2011, 08:06 PM

Quote:

Originally Posted by flashburn

Yeah, same here. I don't really like this dude saying basically "you guys are only acting like you got gains because you are loyal to Stillen and you spent a lot of money". The gains are PROVEN, end of story. You "feeling" like stock is better, is just that, a feeling, with no proof what-so-ever to back it up. If there was hard proof that the stock intakes were better than the G3's, I'd rip them off in a heart beat, and I bet that many others here feel the same way.

You guys are funny. No one accused you of anything. I never said there was anything wrong with the Stillen (it just happened to be what was being discussed). They make some power on a dyno... no doubt. My point is (again), you cannot accurately measure the performance of the stock air box on a dyno. There is evidence of this. I can't link the research and articles because they are on other sites (I tried and it was blocked). If you search you will find the information. Take two deep breaths, chill, and read what I wrote in my first post again.... Please. Thanks.

jran76 · 05-10-2011, 08:12 PM

Quote:

Originally Posted by wstar

On this point: I remember hearing about this in the past, but I don't think stock ECU actually operates in this manner. I've never run my car with the intakes off to visually verify, but when monitoring throttle position sensors (which means the actual throttle plates on our car, not the accel pedal) via Torque or Cipher, it seems they do progressively open just like the throttle plates of any other car. I imagine Osiris or similar should be able to tune them wide open under accel, but I'm not sure.

My car is tuned, and I can tell you it makes little to no difference how far the throttle bodies are opened in regards to throttle response. It is one reason throttle response is not really "tunable" until some cracks the VVEL. You can't really run the car without the intakes connected because the MAF sensors won't get a signal at that point.

05-10-2011, 10:50 AM	#16 (permalink)
jran76 Base Member Join Date: Nov 2009 Location: Plano, TX Posts: 74 Drives: 09 G37S Sedan 6MT Rep Power: 15	No doubt the Stillen makes good power on the dyno compared to the stock boxes, but is hard to simulate what the factory intakes are designed for on a dyno. They are specifically made to operate more effectively while the car is in motion, and designed to force more air in as speed increases (something a dyno cannot replicate). Even with large fans this is difficult to simulate on a dyno. With the above said, Stillen is really the only intake that has proven to produce any noticeable gains on the VQ37VHR, so if you are going to drop your cash on an intake, go with Stillen (not a huge Stillen fan, but I will give them some credit). The 4-5 HP you end up with is not worth $500 and hacking up your car to me, but I know it is to some and you can't argue that they don't sound good. __________________ 2009 G37S Sedan-6MT: Advan / Volk / Tein / SPC / Invidia / Cobb / K&N

05-10-2011, 11:07 AM	#17 (permalink)
jran76 Base Member Join Date: Nov 2009 Location: Plano, TX Posts: 74 Drives: 09 G37S Sedan 6MT Rep Power: 15	I also find it interesting that in the most high performance version of this engine, (used on the Nismo 380RS) they use the exact same stock air boxes. I think if an intake really performed better a) Nismo would know best, and b) they would be all over it. Also, let me remind you, Nismo makes similar intakes for these engines, and they are no where to be found on the most expensive high performance variant of this motor..... EDIT: Actually, after looking into this again, it looks like they switched to a cone style intake in a CF "suction" box, but in the stock locations on the 380RS-C, along with a Motec, and new plenum.... __________________ 2009 G37S Sedan-6MT: Advan / Volk / Tein / SPC / Invidia / Cobb / K&N Last edited by jran76; 05-10-2011 at 11:19 AM.

05-10-2011, 11:53 AM	#20 (permalink)
jran76 Base Member Join Date: Nov 2009 Location: Plano, TX Posts: 74 Drives: 09 G37S Sedan 6MT Rep Power: 15	Just a couple comments because I am too lazy to respond to all of it (and I agree with most of what you are saying).... Turbulent air is more of an issue at the MAF sensors, or pre-MAF, and I will agree that in general turbulent air is a bad thing (it just has less of an affect once being sucked in under vacuum). The biggest issue (and one that some aftermarket intakes suffer from) is the affect of turbulent air has on readings by the MAF sensor. I do think Stillen's design helps keep turbulent air to a minimum pre-MAF, and one of the primary reasons it performs better than most other aftermarket intakes. From all the testing I have seen (by 2-3 extremely reputable companies), there is nothing to indicate the stock boxes are in any way restrictive, or cannot provide enough air to the engine. I think the Stillen brings in slightly cooler and more air on the dyno, and that is the big advantage. At speed, I don't think the amount of air the factory boxes can flow is an issue. They are also bringing in a lot of the cooler air the Stillen is going to pull in once the car is in motion. Also, one last comment on the throttle plates/bodies, according to Mike Kojima (who did a lot of research on the VQ37VHR early on): "The unique VVEL system completely controls the intake valves opening and closing events.... The command authority of the VVEL system is great enough so controlling valve opening is the primary means of throttling the VQ37VHR’s output, instead of traditional throttle plates.The VQ37VHR does retain twin drive by wire throttles but they mostly stay wide open, the only time they close is on overrun to help provide engine braking and if the engines ECU detects low vacuum in the brake booster reservoir." Reference (full article): Edit.... The link is blocked, I guess because it is from another site (god forbid should we share relevant information). If anyone really cares about it, I am sure you can search for Mike Kojima's site and find the article I quoted. __________________ 2009 G37S Sedan-6MT: Advan / Volk / Tein / SPC / Invidia / Cobb / K&N Last edited by jran76; 05-10-2011 at 11:57 AM.

05-10-2011, 12:04 PM	#21 (permalink)
jran76 Base Member Join Date: Nov 2009 Location: Plano, TX Posts: 74 Drives: 09 G37S Sedan 6MT Rep Power: 15	One more thing.... I know there are lot of people on here that love their Stillen intakes, and I think that is great. You are very passionate about them, and I know I am not going to change your mind. There is nothing wrong with the Stillen intake. It is a lot better than any other aftermarket intake I have seen or researched. My only point is that the stock air boxes are not a problem compared to some of the other restrictions. __________________ 2009 G37S Sedan-6MT: Advan / Volk / Tein / SPC / Invidia / Cobb / K&N

05-10-2011, 12:47 PM	#22 (permalink)
Z eliminator A True Z Fanatic Join Date: Jul 2009 Location: Ontario Canada Posts: 1,659 Drives: 370 Z 7AT Sports Rep Power: 18	My G3 stillen made 20 rwhp over the stock intake. It was my first mod. baseline stock car 264.. with stillen 284.rwhp SAE. Mine is a 7 AT. sports have the dyno charts to back it up. Z __________________ 12.343 @114.14 . 4.5 stroker motor is now being built. Dec 1 2015.

05-10-2011, 11:39 AM	#19 (permalink)
OKC Z Base Member Join Date: Feb 2011 Location: OKC Posts: 205 Drives: '09 370z-$old 9/1/12 Rep Power: 14	Aaaamen!! Good sermon.

05-10-2011, 03:14 PM	#25 (permalink)
Joka4411 Base Member Join Date: May 2010 Location: Baltimore Md Posts: 131 Drives: 40th anniver 370Z Rep Power: 15	I am not really in to a lot of the tech stuff about the air intake system, But I do know that my car performs better with the stock intakes, Also thanks for all the positive feed back. __________________ 2010 40th Anniversary Z Owner

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HKS drop ins	Rays	Intake/Exhaust	26	08-25-2010 09:28 AM
get a drop box!	saqib55	The Lounge (Off Topic)	4	07-03-2010 08:15 PM
anybody use k&n drop-ins for they're z?	O'DoyleRules	Intake/Exhaust	3	12-14-2009 09:41 AM
K&N Drop-ins?	blinkme323	Intake/Exhaust	28	11-15-2009 07:34 PM
K&N drop in vs HKS drop in	ddvette9	Intake/Exhaust	2	11-01-2009 12:30 PM