MOTORDYNE ART Pipes - Review

MaDMaXX · 03-13-2012, 07:24 PM

I believe the sound is a bit louder when you get on it.

happytheman · 03-13-2012, 08:28 PM

Quote:

Originally Posted by harp00n

Has anybody tried ART pipes on the stock exhaust?

I plan to change my car to G37x '09 sedan and it has stock exhaust, so I wonder how would it sound with the ART pipes (I believe stock exhaust is almost the same on G37 and 370z)?

Yes. I read someone's comments a couple of weeks ago and he said it was just a little louder than stock, yet where he heard it most was on downshifts where the sport transmission blips the throttle to rpm match. I'll see if I can find that post for you.

happytheman · 03-13-2012, 09:08 PM

Here's one post, but it's not the one I was looking for:

Quote:

Originally Posted by Srenity

Good morning Z community! I finished the install of the ART pipes last night. I have not started the car yet due to giving the RVT time to cure overnight. I hope to drive it a bit today and give her a wash. I will report back. Right now I am on the stock exhuast as I am waiting for the modules to come out for the Motordyne E370 exhaust.

MaDMaXX · 03-13-2012, 09:41 PM

Link to that thread?

happytheman · 03-14-2012, 12:15 AM

Here you go:

What did you do with your Z today II

ZeN · 03-15-2012, 12:37 PM

Guys..how does this Art Pipe V3 pair with AAM shorty, will it gained back those torque or it will be worse since there's not much backpressure. Would love to hear this combo + rep for those owner that chip in. I had a custom shorty with everything else stock, would love to put this art pipe if i could gain back my TQ

Motordyne · 03-15-2012, 01:38 PM

The shorties shouldn't really affect your power/torque much up or down.

The ART pipes however will make a lot more power than the stock cats.

Alpha Ice · 05-10-2012, 09:42 PM

Quote:

Originally Posted by Armonster

Yeah, I am not getting the rasp-type hiss that aadosx is describing. My hissing sounds like a huge volume of air flowing around a sharp corner or something, and never happens unless I am heavy on the gas pedal. I think it continues up to redline, but the engine and exhaust are so loud by that point that I don't notice the hiss as much. It's quite loud, though.

The only other thing I sometimes hear while not accelerating is a burbling sound between shifts at high rpms. I kinda like that sound, though.

I'm from the Myg37 forum, but I recently purchased the ART Test Pipes and am having some hissing sound that sounds very similar to this or pinging sound. I have the Gemini exhaust, and I'm not sure if it is the exhaust or anything is the reason....but I thought I would throw it out there for others to ask. I have a 2010 G37S 6MT Sedan. Any help would be greatly appreciated it!

Staples · 05-10-2012, 09:56 PM

Quote:

Originally Posted by Alpha Ice

I'm from the Myg37 forum, but I recently purchased the ART Test Pipes and am having some hissing sound that sounds very similar to this or pinging sound. I have the Gemini exhaust, and I'm not sure if it is the exhaust or anything is the reason....but I thought I would throw it out there for others to ask. I have a 2010 G37S 6MT Sedan. Any help would be greatly appreciated it!

The Invidia Gemini will do that with just the catback, but will be more pronounced with high flow cats or test pipes (no matter which brand). It's just the nature of the exhaust.

Armonster · 05-11-2012, 10:16 AM

Quote:

Originally Posted by Alpha Ice

I'm from the Myg37 forum, but I recently purchased the ART Test Pipes and am having some hissing sound that sounds very similar to this or pinging sound. I have the Gemini exhaust, and I'm not sure if it is the exhaust or anything is the reason....but I thought I would throw it out there for others to ask. I have a 2010 G37S 6MT Sedan. Any help would be greatly appreciated it!

For what it's worth, my hissing sound was mostly gone after a couple thousand miles. If you have the old style gaskets you may want to replace those before you get an exhaust leak, though.

CorbinDallas · 05-11-2012, 10:35 AM

Quote:

Originally Posted by Armonster

For what it's worth, my hissing sound was mostly gone after a couple thousand miles. If you have the old style gaskets you may want to replace those before you get an exhaust leak, though.

Did you end up using some type of gasket where the ART pipe meets the headers, or did you use permatext copper?

Armonster · 05-11-2012, 11:54 AM

I used the copper stuff and it has been fine since then. The older style was a physical gasket that failed pretty quickly, but have since been discontinued.

indyn · 05-11-2012, 12:02 PM

Quote:

Originally Posted by Armonster

I used the copper stuff and it has been fine since then. The older style was a physical gasket that failed pretty quickly, but have since been discontinued.

how many miles with copper stuff?

Coon-azz · 05-11-2012, 12:23 PM

Quote:

Originally Posted by Boost_lee

thanks for the review, Im highly considering these in the future!

As am I.

Alpha Ice · 05-11-2012, 01:43 PM

Quote:

Originally Posted by Staples

The Invidia Gemini will do that with just the catback, but will be more pronounced with high flow cats or test pipes (no matter which brand). It's just the nature of the exhaust.

I had Berk HFC and my Gemini and I loved the sound. I wanted something deeper and throatier under exhaust, but still compliant with sound cruising. Mine don't have the dampening tabs but DID come with the RTV sealant. I'm assuming mine are the first generation ones though and like many of the people here said over the last 5 months they will come around nicely after 1,500 miles

We are conveniently heading to ZDayz on Tuesday, so that will take no time at all. I loved the sound of cats, but these do have some added power on the butt dyno....it just makes me not wanna WOT cuz of the sound. Next week when I add 3,000 miles to my car I'll post back. Sad to go from 8,600 miles to 12,000 miles over the next couple weeks

03-14-2012, 12:15 AM	#1145 (permalink)
happytheman A True Z Fanatic Join Date: Apr 2010 Location: Florida Posts: 10,737 Drives: MB 6M Tour/Sport Z34 Rep Power: 1822	Here you go: What did you do with your Z today II __________________ --Brantly-- *PowderCoating by Mike/Stillen/PWJDM/Shine Auto/NST* GTR/Michelin /Fast Intentions/Evo-R/Mobil 1/Motul/Z1 https://facebook.com/CentralFloridaZClub

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Review: Motordyne M370 Manifold w/ Comparisons	Staples	Intake/Exhaust	66	06-21-2014 01:35 PM
Motordyne test pipes?	Dan Z Man	Intake/Exhaust	37	12-15-2010 09:12 PM
Motordyne Intake Manifold on the way!!	GZ3	Intake/Exhaust	67	09-16-2010 12:49 AM
another FI 18" CF CBE review w/ test pipes	mrdino77	Intake/Exhaust	9	05-27-2010 12:13 PM

03-13-2012, 07:24 PM	#1141 (permalink)
MaDMaXX Enthusiast Member Join Date: Jan 2012 Location: Oregon from England Posts: 292 Drives: 350z Rep Power: 13	I believe the sound is a bit louder when you get on it.

03-13-2012, 09:41 PM	#1144 (permalink)
MaDMaXX Enthusiast Member Join Date: Jan 2012 Location: Oregon from England Posts: 292 Drives: 350z Rep Power: 13	Link to that thread?

03-15-2012, 12:37 PM	#1146 (permalink)
ZeN Base Member Join Date: Apr 2011 Location: Malaysia Posts: 115 Drives: 09 PW 7AT 370z Rep Power: 14	Guys..how does this Art Pipe V3 pair with AAM shorty, will it gained back those torque or it will be worse since there's not much backpressure. Would love to hear this combo + rep for those owner that chip in. I had a custom shorty with everything else stock, would love to put this art pipe if i could gain back my TQ

03-15-2012, 01:38 PM	#1147 (permalink)
Motordyne Enthusiast Member Join Date: Nov 2008 Location: Los Angeles Posts: 384 Drives: Z Rep Power: 16	The shorties shouldn't really affect your power/torque much up or down. The ART pipes however will make a lot more power than the stock cats.

05-11-2012, 11:54 AM	#1152 (permalink)
Armonster Enthusiast Member Join Date: Mar 2011 Location: Atlanta, GA Posts: 270 Drives: 2010 370z t/sp/6mt Rep Power: 14	I used the copper stuff and it has been fine since then. The older style was a physical gasket that failed pretty quickly, but have since been discontinued.